Kenwood DX-7 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood DX-7 manuals!
Problems with Kenwood DX-7?
Ask a Question
Free Kenwood DX-7 manuals!
Problems with Kenwood DX-7?
Ask a Question
Popular Kenwood DX-7 Manual Pages
User Manual - Page 1
... serial number, found bottom of the unit in the space provided below. Model DX-7 Serial number
©PRINTED IN JAPAN 860·0410·08 CK,M,U,UE,E,THTI 911121110987654321 m
DIGITAL AUDIO TAPE RECORDER
DX-7
INSTRUCTION MANUAL
KENWOOD CORPORATION
For your dealer for information or service on the warranty card, and in the spaces designated on this product.
User Manual - Page 2
...setting of AC adaptor
Important! ANYONE WISHING TO COpy COMMERCIALLY AVAILABLE TAPES OR DISCS SHOULD CONTACT THE MECHANICAL COPYRIGHT PROTECTION SOCIETY LIMITED OR THE PERFORMING RIGHTS SOCIETY LIMITED.
2 DX... make sure that you retain the original carton and packing materials for the proper setting of shipping damage. Before connecting the power cord to the following direction. WARNING:...
User Manual - Page 3
DX-7 3 Precautions ... headphones for long periods may form inside the unit.)
• Using headphones
• DAT players have such a low noise level that there is condensation inside the unit, preventing ...Be careful not to fall asleep while listening to protect your ears from operating normally.
Set the sound volume to an appropriate level to music using or storing it in the following...
User Manual - Page 6
Controls, connectors and indicators
®
® ®@® @®
@ @@
f-
,
'VEl"S - PLAY/RE EAT ST lEJECT
:tR, ,-:1!- ,- I'- , -10',IRm ,,-,I.0,'-, ,
(r>/
User Manual - Page 8
When disconnecting the AC adaptor as well, be sure to set the [POWER] switch to OFF before connecting. Power source
• How to use the unit with... rear panel, then connect the power plug to a household AC power outlet.
• Always set the [POWER] switch to OFF before turning the car's ignition key OFF.
8 DX-7 Also, be sure to first turn the [POWER] switch OFF. (Not doing so may ...
User Manual - Page 12
... to the "R" (right channel) input jack and the white plug to the "L" (left channell input jack.
• Sound volume adjustment: Set the main unit's [VOLUME] control to the amplifier's external input jacks (AUX jacks, TAPE PLAY jacks, etc.). When connecting to the supplied...connections.
• Using the supplied analog connection cord, connect the 3-pin miniplug to this unit's [ I J :
12 DX-7
User Manual - Page 14
... unit ignores any of the remote controller's buttons is ignored.
• When you set the remote controller's [REC HOLD] switch to the " . Key Hold function
Setting this function prevents incorrect operation of the remote controller's [REC] button is ignored.
14 DX-7 " position (so that the white indicator appears). operation of any button operation...
User Manual - Page 15
... again.
Operation is loaded, the tune number for that tune will be displayed from the unit and set the [POWER] switch to play such a tape, "NO PLAY" appears on the display. •... displayed. Tune number display
~
11.-'
r
u-CoJ
Totaf elapsed time display
• To stop mode.
DX-7 15 Tune numbers will not be played. To playback a OAT cassette (Basic operation)
First load a ...
User Manual - Page 18
When starting recording from another DAT deck using a tape recorded with either the main unit or the remote controller.
Digital recording
First load a tape into the unit (see page 14). ""LILI
~..., the same subcodes are recorded on the new tape. Operation is automatically recorded at the start recording.
LIr l I ST·ID mi1ll1.1•1 -,
I
ULI :J
18 DX-7
User Manual - Page 19
...REPEAT] button. If this occurs, lower the recording level slightly.
=, "
'ST.ID [jjg] ..
'_"
Un'nU_'
DX-7 19 When starting recording from a microphone.
1[1[/:: ~II I~
~~I~dB~I~-~5~O~24~'~2~3~O"'V"'ER~
MIC (ATT] OdB 20dB LINE
l'... (BP-A7), First load a tape into the unit (see page 14), Operation is too high, set the "MIG (ATT)' , switch to "20 dB".
• Press the [PLAY/REPEAT] button ...
User Manual - Page 20
... the [DIGITAL I/O] jack. • Do not attach the separately sold AID converter unit.
20 DX-7 Stopping/pausing recording
• Operation is recorded for nine seconds, the unit enters stop mode.1
• Erasing a recording
• To erase a tape, set the unit to record mode with either the main unit or the remote controller...
User Manual - Page 21
DX-7 21 If condensation forms inside the unit, recording or playback will not start when the set time arrives.
• When carrying out analog recording (page 191, adjust the recording level before connecting the timer.
• When not using a timer, do not set the [POWER]
switch to "TIMER".
• When using a timer, make sure...
User Manual - Page 23
... recorded contents. Also, the tune number for this signal is continued from the end of the source being recorded, ST-IOs may not be recorded manually during playback or fast-forwarding. When recording starts and sound is detected after recording was stopped or paused.
• Depending on the tapes. OX-7 23...
User Manual - Page 24
...than 99 tune numbers.
• If no STID is recorded at least 9 seconds between tunes, you can manually write ST-IDs in the appropriate locations while recording is being carried out.
• After writing a ST-..., press the
(REGl button again. sary ST-IDs, renumber the tunes. (See page 25.)
24 DX-7 REW
FF
• The unit enters ST-ID record-standby mode and the following procedure to add ...
User Manual - Page 28
For this reason specifications may
be changed without notice.
28 DX-7 Below measurable limit (EIAJ)
Digital I
Signal-to ...Terminal for digital recording I /O terminal Coaxial: 3.5 mm diameter 4-pin minijack
Analog output terminal........ Specifications
Tape recording system DAT rotating head system
Tape speed 8.15 mm/sec
Sampling frequency 48 kHz/44.1 kHz/32 kHz...
Kenwood DX-7 Reviews
We have not received any reviews for Kenwood yet.