JET Tools J-7060 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools J-7060 manuals!
Problems with JET Tools J-7060?
Ask a Question
Free JET Tools J-7060 manuals!
Problems with JET Tools J-7060?
Ask a Question
Popular JET Tools J-7060 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
20-inch x 20-inch Semi-Automatic Band Saw
Model J-7060
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
1
Part No. M-414476 Revision B 06/2014 Copyright © 2014 JET
User Manual - Page 2
... of one of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects. JET® branded products are made specifically for commercial or industrial purposes default to the JET brand.
2 Heavy-Duty Air Tools; Pro-Duty Air Tools 2 Year - Woodworking Machinery Limited Lifetime - Manual Hoists; Manual Hoist Accessories; What...
User Manual - Page 4
... the machine. Specifications
Model Stock Number
Cutting Capacity At ...tool rooms, and fabrication and welding shops. The rapid acting, patented, 3jaw vise provides simple, fast, and accurate set-ups for both straight and miter cuts. The exclusive 6-point contact blade guide assemblies give the machine greater accuracy and longer blade life.
General Specifications
The JET J-7060...
User Manual - Page 5
... and Parts Manual when changing accessory tools or parts. - Don't force a tool or attach- Always follow instructions in following all of eye wear which comply with side shields (See ANSI Z87.1) - However, any machine used and
serviced properly. - Machinery General Safety Warnings
1. Use of these simple rules for best footing.
3. Failure to maintain proper working...
User Manual - Page 6
... Instructions ...specifications could
shall be started and you are recom-
4.
General Electrical Cautions
19. Know the tool you should allow the saw to
result in order to deliver ample voltage to the workpiece.
All doors shall be stopped and electrical supply must be closed, all panels replaced, and
servicing...guides...support mechanism is not in accordance with the
specifications...
User Manual - Page 7
... JET 12-inch by 20-inch Cut Off Band Saw, Model J-7060.
The hydraulic pump provides the hydraulic pressure required to Figure 1 and 2 for cut-off saw features
Control Panel
Blade Guide Supports
Blade Wheel Cover Blade Speed Control
Operating Instructions
Controls
The operating controls for the saw are provided in a convenient location. This manual also includes parts...
User Manual - Page 8
... following : 1. The feed rate graduations available on the right end of controls include the following controls: 1. Blade guide support adjustment: used to the on the barrel of 25 meters per minute, the indicator would be set a speed rate of the
adjustment mechanism. The saw head, press the Saw Head Up pushbutton. The indicator...
User Manual - Page 9
...provide the operator with very specific instructions regarding the best blade (and coolant...tool steel, or titanium, you with a means to -cut ,
increase the feed rate slightly and allow the saw head is , either blue or straw-colored from JET.
See Setting...service. The further the valve is cutting at which is easily damaged if a careful break-in the vise. Blade Break-in of specific...
User Manual - Page 11
...as required to cut some of the cut . The blade guides are required to place the stop post against the work piece. Mix one part of water). Adjust the feed rate so the hydraulic cylinder ...coolants on the top,
rear of the saw head. The stop L-bracket. ing, refer to the Trouble- If the
performance of the saw begins to deteriorate, the first item that can draw into the workpiece ...
User Manual - Page 14
...of stock diameter. Refer to the coolant supplier's
instructions for a test cut from the coolant tank. ...every six months. 3.
Blade guide bearing: the bearings are ...Limit Switches
sealed-periodic lubrication is low, service reservoir (refer to
the type of ...switch stop .
2. To set the upper limit switch, loosen...screw is kept free of the support bracket).
6. After cleaning, coat...
User Manual - Page 15
... of saw . 7. Install reservoir fill cap. 6. Install the left blade guide support. Set the arm at low ...OFF ALL ELECTRICAL POWER TO THE MACHINE.
1. Servicing Hydraulic Oil
WARNING: SHUT OFF ALL ELECTRICAL ...Replacing the Drive Motor
1. Disconnect the motor from the idler and drive wheels. Loosen the blade enough to pivot downward.
7. Check the guide bearings and the carbide guides...
User Manual - Page 16
... blade (see Changing Blades). Inspection: Examine drive edge and shoulder of Carbide
tion, Replace if faulty. 6. Install the key in the keyway in the
1. Install the blade (see Changing Blades).
2. Replacement of the wheel for damage. The blade guide supports allow you to set to just clear the workpiece to be cut -off saw blade (see figure...
User Manual - Page 18
... to be doing . Therefore, the only setup operations required before releasing the saw for the stock, and the infeed and outfeed supports. If you are installing the motor power cord into a
receptacle, make... for service. Remove the saw from the
power source, or that were used to secure the saw to a
junction box, connect the wires in Figures 21 and 22.)
WARNING: JET RECOMMENDS ...
User Manual - Page 22
Also provided are parts listings that show the replacement parts for the Model J-7060 12-Inch x 20-Inch Semi-Automatic Horizontal Cut-Off Band Saw. Be sure to include the model number and serial number of your machine when ordering replacement parts to the item number in the parts listing. Order replacement parts from:
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph...
User Manual - Page 27
...Guide, Right
1
174 J-5512274 Seat, Support Bracket
1
218 5512312 Screw
1
253 J-5512350 Cover, Blade Wheel (Right) 1
175 5512156 Washer, Lock (M8)
3
219 5512192 Bolt, Hex Cap (M12X35)
2
254 5512222 Screw, Pan Head (M6X15)
4
176 5512275 Belt (1922V321)
1
220 J-5512314 Screw, Set...
Qty No. Model J-7060 Semi-Automatic Cut-Off Band Saw
Ref Part
Ref Part
Ref Part
No. Saw Head...
JET Tools J-7060 Reviews
Do you have an experience with the JET Tools J-7060 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!