JET Tools FS-1652J Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools FS-1652J manuals!
Problems with JET Tools FS-1652J?
Ask a Question
Free JET Tools FS-1652J manuals!
Problems with JET Tools FS-1652J?
Ask a Question
Popular JET Tools FS-1652J Manual Pages
User Manual - Page 1
Operating Instructions and Parts Manual
16 x 52 inch Foot Shear
Model FS-1652J
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-756202 Edition 1 10/2015
Copyright © 2015 JET
User Manual - Page 2
....
15. Keep children away.
16. Follow instructions for the best and safest performance. Do not use .
6. Before operating the foot shear, remove tie, rings, watches and other reproductive harm. Looking around the machine clean and free of these chemicals are specifically designed to perform any other part that may cause serious injury.
3. improper...
User Manual - Page 3
...SAVE THESE INSTRUCTIONS
2.0 About this manual for a JET Model FS1652T Foot Shear.
This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
... if used in this manual:
This means that if precautions are not heeded, it interferes in any way with the instructions as set forth in minor injury ...
User Manual - Page 4
...1.0 IMPORTANT SAFETY INSTRUCTIONS ...2 2.0 About this manual ...3 3.0 Table of contents...4 4.0 Specifications ...5 5.0 Setup and assembly...6
5.1 Shipping contents...6 5.2 Tools required for assembly ......8 9.0 Troubleshooting FS-1652T Foot Shear...8 10.0 Replacement Parts...8 10.1.1 Exploded View: FS-1652J Foot Shear 9 10.1.2 Parts List: FS-1652J Foot Shear ...10 11.0 Warranty and service ...12
...
User Manual - Page 5
4.0 Specifications
Model number ...FS-1652T Stock number ...756202 Capacities:
Mild steel...16 gauge Maximum ...499 kg) Shipping weight ...1220 lbs (554 kg)
The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations...
User Manual - Page 6
... table surface. Figure 2
5.2 Tools required for shipping damage. Report ...Install four hex cap bolts and washers (I 4 Flat washers, wide, M12 - Remove crating from around blade area.
5. Inspect contents for assembly
16mm and 19mm wrenches
5.3 Unpacking and cleanup
1. Failure to all assembly instructions... operation. 5.0 Setup and assembly
Read and understand all sides. Install T-nuts, flat washers...
User Manual - Page 7
... scales are complete. Loosen hex nuts and bolts (S, Figure 5). Retighten hex nut against frame. If the shear does not cut properly during operations, identify the specific problem: Place heavy sheet of paper. Distance between material and table while operating shear. 2. If adjustment is level but shear does not sit evenly, adjust as...
User Manual - Page 8
... Troubleshooting FS-...parts or reach our service...guides.
Bottom blade is bowed.
Turn or sharpen blade(s). Incorrect blade clearance, excessive Adjust blades closer.
Blade is 2-way and can be flipped once for equal blade gap.
Tighten gibs. Replace blade.
10.0 Replacement Parts
Replacement parts are provided with the foot shear, should installed ones need replacing...
User Manual - Page 10
Side Panel 1 5 FS1652J-05 L.H. 10.1.2 Parts List: FS-1652J Foot Shear
Index No Part No
Description
Size
Qty
1 FS1652J-01 Table...1 2 FS1652J-02 Cutter Bar ...1 3 FS1652J-03 Hold Down ...1 4 FS1652J-04 R.H. Side Panel 1 6 FS1652J-06 Front Extension Arm 2 7 F009545 Hex Cap Bolt M12-1.75x45 4 8 FS1652J-08 Spring ...2 9 FS1652J-09 Stud ...2 10 F004545 Cap Nut M12-1.75...
User Manual - Page 11
... Gauge 1 76 F003835 Cotter Pin 3.2x45 mm 10 77 F002636 Flat Washer 6xØ12x1.6 mm 5 78 FS1652J-78 Scale...2 79 FS1652J-79 Rivet 2x5 mm 4 LM000077 ID Label, FS-1652J (not shown 1 LM000135 Label - Non-proprietary parts, such as fasteners, can usually be found at local hardware stores, or may not be ordered from...
User Manual - Page 12
... for commercial or industrial purposes default to be asked to Get Technical Support Please contact Technical Service by JPW Industries, Inc. Consumable items 1 Year - JET Parallel clamps; Shop Tools; If one year from the date of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects.
What is Covered This...
JET Tools FS-1652J Reviews
We have not received any reviews for JET Tools yet.