Invacare FRC3 Support and Manuals
Get Help and Manuals for this Invacare item
View All Support Options Below
Free Invacare FRC3 manuals!
Problems with Invacare FRC3?
Ask a Question
Free Invacare FRC3 manuals!
Problems with Invacare FRC3?
Ask a Question
Popular Invacare FRC3 Manual Pages
Assembly Instructions - Page 1
Assembly Instructions Invacare® Top End® Force™-3 Handcycle
1181408 REV A
Be sure to record your serial number and read the owners manual.
Assembly Instructions - Page 2
... receive:
Box includes: Before disposing of hardware including 2 rear wheel axles, 2 split half clamps, 4 bolts, 4 washers, 4 locknuts, 2 footrest straps, 2 axle caps and the assembly instructions
1181408 REV A seat cushion » 2 - footrest assemblies » 1 - drafting bumper » 1 - flag » 1 - back cushion » 1 - wrap around frame with seat upholstery and back...
Assembly Instructions - Page 4
Step 1: Set up
Remove all contents from box and use the box as a mat for assembling.
Double check the box to be sure all parts are removed.
Take the cardboard off of the frame and leave the plastic on the frame to avoid scratches.
1181408 REV A
Assembly Instructions - Page 6
Step 3: Securing the Backrest
Loosen the pivot clamp and then insert backrest support tube into the pivot clamp that is welded to the camber bar.
Use a 5mm Allen wrench to tighten securely.
Note: It will be easier to attach the cushion if the backrest is tightened in the most reclined position.
1181408 REV A
Assembly Instructions - Page 7
Step 4: Installing Drafting Bumper
Loosen the drafting bumper receiver clamps using a 5mm Allen wrench.
Insert drafting bumper into receiver clamps.
Use 5mm Allen wrench to tighten the receiver clamps.
1181408 REV A
Assembly Instructions - Page 8
Step 5: Installing the Cushions
• Bend seat cushion in the future.
• Remove the loop fastener strip from the back cushion (it has a yellow film covering the ...
Assembly Instructions - Page 9
... a 4mm Allen wrench to remove the headtube caps. 2. Raise the front half of the bike off of the ground by using 5mm Allen wrench and set aside for attaching the fork:
1.
Assembly Instructions - Page 11
... assembly until there is no movement. Notes
To make sure the crank assembly is tight and straight and does not pivot. There should be installed (one .
Also, make sure there is straight. Then tighten the half clamps down again.
Align the fork into the straight position and then...
Assembly Instructions - Page 12
Step 7: Installing the Footrests Engage parking brake. Remove the box from under the handcycle. Loosen both bolts on the footrest clamp on each side using 4mm Allen wrench. Insert the footrest into the clamps. Tighten securely using 4mm Allen wrench and 10mm wrench.
1181408 REV A
Assembly Instructions - Page 14
Step 9: Installing the Safety Flag
Insert the two posts of the flag together and then insert into the flag holder on the back of the bike.
1181408 REV A
Assembly Instructions - Page 16
Before Riding Your New Handcycle (CONT.) Engage your hand brake, and make sure the disc brake caliper engages. Check your parking brake again, and make sure not only that it engages but also that the pads
are lined up on the metal part of the wheel rim. Pump up your tires to 100 PSI.
1181408 REV A
Assembly Instructions - Page 17
... serial number and please refer to Invacare Corporation unless otherwise noted. All trademarks are identified by or licensed to our Force Series Owner's manual online (topendwheelchair.com) for instructions on proper fitting, operation and safety of your new Invacare Top End Force-3 handcycle.
If you have any questions, please call Invacare...
Invacare FRC3 Reviews
We have not received any reviews for Invacare yet.