Instruction Manual
Page 18
...PC using a USB cable. u USB (Universal Serial Bus) CONNECTOR (B type) [USB] (B) Connect a USB cable to the PC. trical shocks, TVI, BCI and other problems. w ANTENNA CONNECTOR 1 [ANT1] e ANTENNA CONNECTOR 2 [ANT2] (pgs. 17, 112) Accept a 50 ø antenna with a PL-259 plug connec- Rear panel view...t EXTERNAL SPEAKER JACK [EXT-SP] (p. 18) Connects an external speaker (4-8 ø), if desired. About the USB driver: Icom HP (http://www.icom.co.jp/world/support/ index.html) gives the USB driver and the installation guide download service. The following items are required: PC ...
...PC using a USB cable. u USB (Universal Serial Bus) CONNECTOR (B type) [USB] (B) Connect a USB cable to the PC. trical shocks, TVI, BCI and other problems. w ANTENNA CONNECTOR 1 [ANT1] e ANTENNA CONNECTOR 2 [ANT2] (pgs. 17, 112) Accept a 50 ø antenna with a PL-259 plug connec- Rear panel view...t EXTERNAL SPEAKER JACK [EXT-SP] (p. 18) Connects an external speaker (4-8 ø), if desired. About the USB driver: Icom HP (http://www.icom.co.jp/world/support/ index.html) gives the USB driver and the installation guide download service. The following items are required: PC ...
Instruction Manual
Page 24
... GROUND (p. 16) Use the heaviest gauge wire or strap available and make the connection as short as possible. Grounding prevents electrical shocks, TVI and other problems. STRAIGHT KEY 17
... GROUND (p. 16) Use the heaviest gauge wire or strap available and make the connection as short as possible. Grounding prevents electrical shocks, TVI and other problems. STRAIGHT KEY 17
Instruction Manual
Page 151
...attenuator is • Reset the frequency using set too far counter- • Set the [MIC GAIN] control to a suitable posi- If you correct problems which are not equipment malfunctions. function • Set the antenna switch in transmit. • R otate the [AF] control clockwise to obtain a ...position to open the squelch. • P ush [TRANSMIT] to receive or check the p. 36 SEND line of this chart, contact your nearest Icom Dealer or Service Center. band. the function OFF. 88 Transmit signal is unclear or • T he antenna for 1 sec. Sensitivity is too...
...attenuator is • Reset the frequency using set too far counter- • Set the [MIC GAIN] control to a suitable posi- If you correct problems which are not equipment malfunctions. function • Set the antenna switch in transmit. • R otate the [AF] control clockwise to obtain a ...position to open the squelch. • P ush [TRANSMIT] to receive or check the p. 36 SEND line of this chart, contact your nearest Icom Dealer or Service Center. band. the function OFF. 88 Transmit signal is unclear or • T he antenna for 1 sec. Sensitivity is too...
Instruction Manual
Page 152
...• The dial lock function is activated. 7600 screen with "bound," "rotation" or "twist" condition. to p. 82 turn the function OFF. • P ush [EXIT/SET] several times to suit your preference. D Format USB-Memory PROBLEM POSSIBLE CAUSE SOLUTION REF. select the FAT format.... The display indicates the IC- • The screen saver function is activated. select the FAT32 format. ■ Main dial brake adjustment ...
...• The dial lock function is activated. 7600 screen with "bound," "rotation" or "twist" condition. to p. 82 turn the function OFF. • P ush [EXIT/SET] several times to suit your preference. D Format USB-Memory PROBLEM POSSIBLE CAUSE SOLUTION REF. select the FAT format.... The display indicates the IC- • The screen saver function is activated. select the FAT32 format. ■ Main dial brake adjustment ...
Instruction Manual
Page 156
... mode settings after resetting, if desired. w W hile pushing and holding [F-INP ENT] and [MW], push [POWER] to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. Otherwise, a fire, injury or damage the transceiver may occur. ■ Resetting the... cable fuse replacement. CAUTION: Turn the power OFF and disconnect the DC power cable from the DC power cable is installed in advance. The IC-7600 has two fuse types as below installed for transceiver protection. • DC power cable fuses ATC 30 A • Circuitry fuse ATC 5 ...
... mode settings after resetting, if desired. w W hile pushing and holding [F-INP ENT] and [MW], push [POWER] to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. Otherwise, a fire, injury or damage the transceiver may occur. ■ Resetting the... cable fuse replacement. CAUTION: Turn the power OFF and disconnect the DC power cable from the DC power cable is installed in advance. The IC-7600 has two fuse types as below installed for transceiver protection. • DC power cable fuses ATC 30 A • Circuitry fuse ATC 5 ...