Instruction Manual
Page 15
... cable (OPC-599) !3 Connect to 0 V Input impedance : More than 10 k˘ NC --- --- 13.8 V 13.8 V output when power is ON. trical shocks, TVI, BCI and other problems. !1 DC POWER SOCKET [DC 13.8V] (p. 15) Accepts 13.8 V DC through the supplied DC power cable. Output current : Max. 1 A TKEY Key line for the optional...
... cable (OPC-599) !3 Connect to 0 V Input impedance : More than 10 k˘ NC --- --- 13.8 V 13.8 V output when power is ON. trical shocks, TVI, BCI and other problems. !1 DC POWER SOCKET [DC 13.8V] (p. 15) Accepts 13.8 V DC through the supplied DC power cable. Output current : Max. 1 A TKEY Key line for the optional...
Instruction Manual
Page 18
... 00 HM-36 • Rear panel SM-20 DC POWER SUPPLY (p.15) AC outlet A DC power supply 13.8 V; Grounding prevents electrical shocks, TVI and other problems. CW KEY A straight key can be used when the internal electronic keyer is turned OFF in initial set mode. (p. 80) 13 RIT GENE SCAN 8 24...
... 00 HM-36 • Rear panel SM-20 DC POWER SUPPLY (p.15) AC outlet A DC power supply 13.8 V; Grounding prevents electrical shocks, TVI and other problems. CW KEY A straight key can be used when the internal electronic keyer is turned OFF in initial set mode. (p. 80) 13 RIT GENE SCAN 8 24...
Instruction Manual
Page 88
...power cable is installed in the PA unit. ATC 30 A fuse w R eplace the circuitry fuse as shown in the IC-7200, except for the DC power cable fuse replacement. The IC-7200 has two fuses (DC power cable fuses) installed for transceiver protection. • DC power cable fuses ATC 30 A ... the circuitry fuse. 11 MAINTENANCE ■ Fuse replacement If a fuse blows or the transceiver stops functioning, try to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. CAUTION: Disconnect the DC power cable from the transceiver when the PA shielding...
...power cable is installed in the PA unit. ATC 30 A fuse w R eplace the circuitry fuse as shown in the IC-7200, except for the DC power cable fuse replacement. The IC-7200 has two fuses (DC power cable fuses) installed for transceiver protection. • DC power cable fuses ATC 30 A ... the circuitry fuse. 11 MAINTENANCE ■ Fuse replacement If a fuse blows or the transceiver stops functioning, try to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. CAUTION: Disconnect the DC power cable from the transceiver when the PA shielding...
Instruction Manual
Page 90
pushed. • Check for the oper- p. 14 connected. p. 67 lected. POWER SUPPLY PROBLEM POSSIBLE CAUSE SOLUTION REF. Power does not come • DC power cable is cut or shorted. • Check the feed line and correct any im- - ... of an external unit, if connected. • An external speaker or headphones are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center. 12 TROUBLESHOOTING The following chart is designed to turn the function OFF. proper conditions. •...
pushed. • Check for the oper- p. 14 connected. p. 67 lected. POWER SUPPLY PROBLEM POSSIBLE CAUSE SOLUTION REF. Power does not come • DC power cable is cut or shorted. • Check the feed line and correct any im- - ... of an external unit, if connected. • An external speaker or headphones are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center. 12 TROUBLESHOOTING The following chart is designed to turn the function OFF. proper conditions. •...
Instruction Manual
Page 91
... to a suitable po- proper conditions. • The antenna is activated. p. 67 lected. sition. with rotating the [M-CH] control indicator goes out). TROUBLESHOOTING 12 TRANSMIT DISPLAY PROBLEM POSSIBLE CASE SOLUTION REF. been programmed. p. 61 c a n n o t b e s e l e c t e d trol mode. p. 67 tenna or test with the speech compressor ON. does not change prop- No contact possible...
... to a suitable po- proper conditions. • The antenna is activated. p. 67 lected. sition. with rotating the [M-CH] control indicator goes out). TROUBLESHOOTING 12 TRANSMIT DISPLAY PROBLEM POSSIBLE CASE SOLUTION REF. been programmed. p. 61 c a n n o t b e s e l e c t e d trol mode. p. 67 tenna or test with the speech compressor ON. does not change prop- No contact possible...