Instruction Manual
Page 1
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTION MANUAL HF/VHF/UHF ALL MODE TRANSCEIVER i7100 This device complies with Part 15 of the FCC Rules.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTION MANUAL HF/VHF/UHF ALL MODE TRANSCEIVER i7100 This device complies with Part 15 of the FCC Rules.
Instruction Manual
Page 2
...modifications to this device, not expressly approved by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and re- MM" means section number. The IC-7100 hf/vhf/uhf all mode transceiver is encouraged to try to correct the interference by Icom... and, if not installed and used in accordance with the limits for purchasing this fine Icom product. Recommended for your IC-7100. Icom, Icom Inc. CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. Personal ...
...modifications to this device, not expressly approved by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and re- MM" means section number. The IC-7100 hf/vhf/uhf all mode transceiver is encouraged to try to correct the interference by Icom... and, if not installed and used in accordance with the limits for purchasing this fine Icom product. Recommended for your IC-7100. Icom, Icom Inc. CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. Personal ...
Instruction Manual
Page 20
... SET > Connectors > ACC/USB Output Select 1-16 The transceiver outputs a low signal to +0.8 V Maximum 20 mA put pin. NC *3 If the modification is used for the optional AT-180. --- 10 FSKK Controls RTTY keying "High" level: "Low" level: Output current: More than 2.4 V Less than... Output level: control position. 4.7 k˘ 100 to check its switching action before operation. [Example] ACC socket eHSEND or Switching diode To a non-Icom linear amplifier uVSEND i13.8 V Relay *2 V SEND is used for the optional AT-180. --- Output voltage: Output current: 8 V ± 0.3...
... SET > Connectors > ACC/USB Output Select 1-16 The transceiver outputs a low signal to +0.8 V Maximum 20 mA put pin. NC *3 If the modification is used for the optional AT-180. --- 10 FSKK Controls RTTY keying "High" level: "Low" level: Output current: More than 2.4 V Less than... Output level: control position. 4.7 k˘ 100 to check its switching action before operation. [Example] ACC socket eHSEND or Switching diode To a non-Icom linear amplifier uVSEND i13.8 V Relay *2 V SEND is used for the optional AT-180. --- Output voltage: Output current: 8 V ± 0.3...
Advanced Instructions
Page 23
... flow: 2.0 V to 20.0 V -0.5 V to check its switching action before operation. [Example] ACC socket eHSEND or Switching diode To a non-Icom linear amplifier uVSEND i13.8 V Relay *2 V SEND is used for the 144 MHz and 430 MHz bands, and HSEND is performed, (BAND*3) band ... 0 V More than 3.3 k˘ Color refers to An external equipment Input voltage (High): 2.0 V to 8 V ALC ALC voltage input. NC *3 If the modification is used for the optional AT-180. --- Output voltage: Output current: 8 V ± 0.3 V Less than 0.1 V Maximum 200 mA external equipment. BDT Data line...
... flow: 2.0 V to 20.0 V -0.5 V to check its switching action before operation. [Example] ACC socket eHSEND or Switching diode To a non-Icom linear amplifier uVSEND i13.8 V Relay *2 V SEND is used for the 144 MHz and 430 MHz bands, and HSEND is performed, (BAND*3) band ... 0 V More than 3.3 k˘ Color refers to An external equipment Input voltage (High): 2.0 V to 8 V ALC ALC voltage input. NC *3 If the modification is used for the optional AT-180. --- Output voltage: Output current: 8 V ± 0.3 V Less than 0.1 V Maximum 200 mA external equipment. BDT Data line...
Advanced Instructions
Page 303
... V wwGND 76 3 1 54 2 ACeC eH2 SEND rrNC (Rear panel view) ttALC yyNC uu13.8 V DESCRIPTION SPECIFICATIONS Regulated 8 V output when the Band Voltage Same as ACC pin e. modification is ON Same as ACC pin y.
... V wwGND 76 3 1 54 2 ACeC eH2 SEND rrNC (Rear panel view) ttALC yyNC uu13.8 V DESCRIPTION SPECIFICATIONS Regulated 8 V output when the Band Voltage Same as ACC pin e. modification is ON Same as ACC pin y.
Advanced Instructions
Page 344
... file 19-9 Touch screen calibration function 19-10 Dial tuning tension adjustment 19-10 Protection function 19-10 External keypad connections 19-11 Band voltage modification 19-11 Troubleshooting 19-12 DDTransceiver power 19-12 DDTransmit and receive 19-12 DDDisplay 19-13 DDScanning 19-13 DDWhile operating D-STAR 19-14...
... file 19-9 Touch screen calibration function 19-10 Dial tuning tension adjustment 19-10 Protection function 19-10 External keypad connections 19-11 Band voltage modification 19-11 Troubleshooting 19-12 DDTransceiver power 19-12 DDTransmit and receive 19-12 DDDisplay 19-13 DDScanning 19-13 DDWhile operating D-STAR 19-14...