Instruction Manual
Page 2
... are created in the internal circuit and w o does not indicate a transceiver malfunction: 52.76497 MHz, 443.03535 MHz Icom, Icom Inc. This manual contains important safety and operating instructions for optimum use. NOTE Recommended for the IC-7000. FOREWORD We understand that you have a choice of many different radios in Japan, the United States, the United...
... are created in the internal circuit and w o does not indicate a transceiver malfunction: 52.76497 MHz, 443.03535 MHz Icom, Icom Inc. This manual contains important safety and operating instructions for optimum use. NOTE Recommended for the IC-7000. FOREWORD We understand that you have a choice of many different radios in Japan, the United States, the United...
Instruction Manual
Page 30
...AC outlet ( ) Non-European versions : 100-120/200-240 V European version : 230 V Transceiver Coaxial cable (supplied with the IC-7000, before operation. 21 To an antenna RF OUTPUT RF INPUT ALC SEND 50 Ω coaxial cable HSEND (Orange) Transceiver GND Relay ... the range 0 V to the linear amplifier instruction manual. Non-matched ALC and RF power settings could cause a fire or damage the linear amplifier. The IC-7000 SEND line (ACC connector pin 3) is compatible with the IC-PW1/EURO) ANT1 Ground CONNECTING A NON-ICOM LINEAR AMPLIFIER R WARNING!: Set the transceiver...
...AC outlet ( ) Non-European versions : 100-120/200-240 V European version : 230 V Transceiver Coaxial cable (supplied with the IC-7000, before operation. 21 To an antenna RF OUTPUT RF INPUT ALC SEND 50 Ω coaxial cable HSEND (Orange) Transceiver GND Relay ... the range 0 V to the linear amplifier instruction manual. Non-matched ALC and RF power settings could cause a fire or damage the linear amplifier. The IC-7000 SEND line (ACC connector pin 3) is compatible with the IC-PW1/EURO) ANT1 Ground CONNECTING A NON-ICOM LINEAR AMPLIFIER R WARNING!: Set the transceiver...
Instruction Manual
Page 124
... ft long (3.5 MHz and above). • See page 20 for connection. • See the AH-4 instruction manual for each frequency. NEVER operate the AH-4 when it is required for AH-4 installation and antenna connection details. ... from : S-1, S-2 or S-3 Either Y or Z ■ Optional AH-4 automatic antenna tuner operation The AH-4 matches the IC-7000 to re-tune the antenna before transmitting when you change the frequency-even slightly. Note that frequency. r To bypass the AH-4 manually, push [TUNER/ CALL]. RDANGER!: HIGH VOLTAGE! e " " i n d i c a t o r s t ay s O N w...
... ft long (3.5 MHz and above). • See page 20 for connection. • See the AH-4 instruction manual for each frequency. NEVER operate the AH-4 when it is required for AH-4 installation and antenna connection details. ... from : S-1, S-2 or S-3 Either Y or Z ■ Optional AH-4 automatic antenna tuner operation The AH-4 matches the IC-7000 to re-tune the antenna before transmitting when you change the frequency-even slightly. Note that frequency. r To bypass the AH-4 manually, push [TUNER/ CALL]. RDANGER!: HIGH VOLTAGE! e " " i n d i c a t o r s t ay s O N w...
Instruction Manual
Page 142
...- MPW ANF Memo pad write is pro- High or low can be selected. "P.AMP/ATT" (Preamplifier/attenuator), "NB" (Noise blanker), "NR" (Noise reduction), "MNF" (Manual notch filter), "ANF" (Auto notch filter), "TS" (Tuning step), "SPL" (Split operation), "A/B" (VCO A/B selection), "MCL" (Memory clear), "BNK" (Bank selection...) LOW Low speed (2.5 tuning steps/second) 33 Quick RIT/∂TX Clear This item selects the RIT/∂TX frequency clearing instruction for the [F-3 CLR] key. When this function is activated, the received signal will remain the same even when the operating mode...
...- MPW ANF Memo pad write is pro- High or low can be selected. "P.AMP/ATT" (Preamplifier/attenuator), "NB" (Noise blanker), "NR" (Noise reduction), "MNF" (Manual notch filter), "ANF" (Auto notch filter), "TS" (Tuning step), "SPL" (Split operation), "A/B" (VCO A/B selection), "MCL" (Memory clear), "BNK" (Bank selection...) LOW Low speed (2.5 tuning steps/second) 33 Quick RIT/∂TX Clear This item selects the RIT/∂TX frequency clearing instruction for the [F-3 CLR] key. When this function is activated, the received signal will remain the same even when the operating mode...
Service Manual
Page 2
...generator or a sweep generator. 7. Quantity required 5030002820 LCD LTA025A161A IC-7000 8810009610 Screw FH M2.6 × 6 ZK IC-7000 Front unit 5 pieces Top cover10 pieces Addresses are subject to change... NOT apply an RF signal of test equipment thoroughly before disassembling the transceiver. 2. Icom, Icom Inc. DO NOT expose the transceiver to the antenna connector. VER.NO. #02... name and informations 3. READ the instructions of more than 20 dBm (100 mW) to rain, snow or any liquids. INTRODUCTION This service manual describes the latest service information for...
...generator or a sweep generator. 7. Quantity required 5030002820 LCD LTA025A161A IC-7000 8810009610 Screw FH M2.6 × 6 ZK IC-7000 Front unit 5 pieces Top cover10 pieces Addresses are subject to change... NOT apply an RF signal of test equipment thoroughly before disassembling the transceiver. 2. Icom, Icom Inc. DO NOT expose the transceiver to the antenna connector. VER.NO. #02... name and informations 3. READ the instructions of more than 20 dBm (100 mW) to rain, snow or any liquids. INTRODUCTION This service manual describes the latest service information for...