Hard Drive Specifications
Page 6
.../unload 32 6.5 Mechanical specifications 34 6.5.1 Physical dimensions and weight 34 6.5.2 Mounting hole locations 34 6.5.3 Connector and jumper description 35 6.5.4 Mounting orientation 35 6.5.5 Load/unload mechanism 36 6.6 Vibration and shock 37 6.6.1 Operating vibration 37...Write DMA 60 7.9.8 Host Terminating Write DMA 61 7.10 Drive address setting 62 7.11 Drive default address setting 62 7.12 Addressing of HDD registers 63 Part 2. Interface specification 65 8.0 General 67 8.1 Introduction 67 8.2 Terminology 67 Travelstar 48GH, 30GN & 15GN hard disk drive specifications iv
.../unload 32 6.5 Mechanical specifications 34 6.5.1 Physical dimensions and weight 34 6.5.2 Mounting hole locations 34 6.5.3 Connector and jumper description 35 6.5.4 Mounting orientation 35 6.5.5 Load/unload mechanism 36 6.6 Vibration and shock 37 6.6.1 Operating vibration 37...Write DMA 60 7.9.8 Host Terminating Write DMA 61 7.10 Drive address setting 62 7.11 Drive default address setting 62 7.12 Addressing of HDD registers 63 Part 2. Interface specification 65 8.0 General 67 8.1 Introduction 67 8.2 Terminology 67 Travelstar 48GH, 30GN & 15GN hard disk drive specifications iv
Hard Drive Specifications
Page 49
... jumper description A jumper is 3.0±0.3 mm for bottom and 3.5±0.5 mm for horizontal mounting. Performance and error rate will stay within specification limits if the drive is operated in all axes (6 directions) and will stay within the specified error rates when tilted ±5 degrees from which it was formatted. Travelstar 48GH, 30GN & 15GN hard disk drive...
... jumper description A jumper is 3.0±0.3 mm for bottom and 3.5±0.5 mm for horizontal mounting. Performance and error rate will stay within specification limits if the drive is operated in all axes (6 directions) and will stay within the specified error rates when tilted ±5 degrees from which it was formatted. Travelstar 48GH, 30GN & 15GN hard disk drive...
Hard Drive Specifications
Page 56
...serial number, place of information technology equipment, AS/NZS 3548:1995 Class B." The presence of IBM products ! RFI Suppression German National Requirements ! The location on the drive is to every drive: ! and FRU No. ! Travelstar 48GH, 30GN & 15GN hard disk drive specifications 42 6.8 Identification labels The following worldwide electromagnetic compatibility (EMC) requirements: ! A bar ... appears on the top of the HDA containing the statement "Made by the user. ! RFI Japan VCCI, Requirements of labels containing jumper information depending on user request.
...serial number, place of information technology equipment, AS/NZS 3548:1995 Class B." The presence of IBM products ! RFI Suppression German National Requirements ! The location on the drive is to every drive: ! and FRU No. ! Travelstar 48GH, 30GN & 15GN hard disk drive specifications 42 6.8 Identification labels The following worldwide electromagnetic compatibility (EMC) requirements: ! A bar ... appears on the top of the HDA containing the statement "Made by the user. ! RFI Japan VCCI, Requirements of labels containing jumper information depending on user request.
Hard Drive Specifications
Page 63
...jumper on the same AT interface cable to provide status. If CSEL is open or is able to avoid master-master or slave-slave configurations. KEY Pin position 20 has no longer busy and is at a low level, the HDD works as a Slave. Closing the respective position of a valid Execute Drive... seconds to one HDD should clear BSY before asserting PDIAG-, as PDIAG- DMARQ This signal is ready to transfer data to 00h. Travelstar 48GH, 30GN & 15GN hard disk drive specifications 49 The signal level of DIOR- One is the "+5 V Logic" input pin and the second is a flow control signal...
...jumper on the same AT interface cable to provide status. If CSEL is open or is able to avoid master-master or slave-slave configurations. KEY Pin position 20 has no longer busy and is at a low level, the HDD works as a Slave. Closing the respective position of a valid Execute Drive... seconds to one HDD should clear BSY before asserting PDIAG-, as PDIAG- DMARQ This signal is ready to transfer data to 00h. Travelstar 48GH, 30GN & 15GN hard disk drive specifications 49 The signal level of DIOR- One is the "+5 V Logic" input pin and the second is a flow control signal...
Hard Drive Specifications
Page 76
Travelstar 48GH, 30GN & 15GN hard disk drive specifications 62 In the case when pin 28 is ground, or low, the drive is Device 0 (Master). Drive address setting 7.11 Drive default address setting The default setting of jumper at shipment is a Master. Using Cable Selection, the drive address depends on the condition of pin 28 of the jumper is grounded the...
Travelstar 48GH, 30GN & 15GN hard disk drive specifications 62 In the case when pin 28 is ground, or low, the drive is Device 0 (Master). Drive address setting 7.11 Drive default address setting The default setting of jumper at shipment is a Master. Using Cable Selection, the drive address depends on the condition of pin 28 of the jumper is grounded the...
Hard Drive Specifications
Page 145
... 1(=x) 1=Security Enabled 0(=x) 1=Security Supported Figure 86. above ViH 0=Device detected CBLID- Identify device information (6 of 7) Travelstar 48GH, 30GN & 15GN hard disk drive specifications 131 Word Content 93 XXXXH 94-127 0000H 128 0XXXH Description Hardware reset results 15-13 Device detected result 15(=0) Reserved... bits to 0 12(=0) Reserved 11(=X) 1=Device 1 passed diagnostic 10-9(=X) how Device 1 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 8(=1) Always 7-0 Device 0 hardware...
... 1(=x) 1=Security Enabled 0(=x) 1=Security Supported Figure 86. above ViH 0=Device detected CBLID- Identify device information (6 of 7) Travelstar 48GH, 30GN & 15GN hard disk drive specifications 131 Word Content 93 XXXXH 94-127 0000H 128 0XXXH Description Hardware reset results 15-13 Device detected result 15(=0) Reserved... bits to 0 12(=0) Reserved 11(=X) 1=Device 1 passed diagnostic 10-9(=X) how Device 1 determined the device number: 00=Reserved 01=a jumper was used 10=the CSEL signal was used 11=some other method was used or the method is unknown 8(=1) Always 7-0 Device 0 hardware...