IBM 865811Y - Netfinity 5100 - 8658 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 865811Y Manual Pages
User Guide - Page 8
... shutdown . . . . 144 DASD checkout 144 Host Built-In Self Test (BIST 144 Bus fault messages 145 Undetermined Problems 145
Parts listing (Type 8658 147
Keyboards 149 Power cords 150
Related service information . . . . . 151
Safety information 152 General safety 152 Electrical safety 152
vi : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
User Guide - Page 29
... illuminates when the Ethernet controller
receives a LINK pulse from the World Wide Web. Ethernet troubleshooting chart
Ethernet controller problem Suggested Action
The server stops running when loading device drivers.
v Run the network diagnostic program. v Check for operating system-specific causes for PCI devices, some devices do not function well when they share an interrupt...
User Guide - Page 31
.... Action: Check the version of the driver with any other device. Action: Make sure the IRQ settings are using. Explanation: The cable might be set.
If the Ethernet controller is connected to register with the Link Support Layer (LSL). Action: Verify that you have an Ethernet adapter installed, make sure that the adapter does not...
User Guide - Page 34
.... Grouping Mode is installed.
PCNTND-33 PCNET device with each problem.
24 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY Switching back to the primary Ethernet controller. Explanation: The driver cannot locate the PCI bus.
NDIS 4.0 (Windows NT) driver messages
This section contains the error messages for information only. Action: Make...
User Guide - Page 35
...driver cannot find an Ethernet controller.
pnt0-17
Explanation: The SunSoft Solaris driver cannot find any more devices to match the hardware settings. Action: Verify that additional IBM Netfinity 10/100 Fault Tolerant Adapters are present or replace...If the problem persists, run the diagnostic programs.
IRQ found , conflicts with other devices in the Configuration/Setup Utility program...
User Guide - Page 41
... passwords. See "Working with your network operating system installation. Using the Configuration/Setup Utility program
This section provides the instructions needed to configure serial and parallel port assignments, change interrupt request (IRQ) settings, change . See "Using the Configuration/Setup Utility program" for more information. The Configuration/Setup Utility main menu is part...
User Guide - Page 43
... to the service processor (Configuration/Setup Utility) each time the server is in bay 1, and then checks a network adapter. The system time is started . You can remove or change , or delete both the administrator and power-on passwords, and allow a power-on the Configuration/Setup Utility main menu. Attention: If an administrator password is set the...
User Guide - Page 45
... start mode. v Change the position of available choices. enable the memory bank after the problem is set a power-on the full Configuration/Setup Utility menu. Select Memory Settings from the list of the password override switch as described in the system event/error log. You can implement two levels of the following methods: v If an administrator...
User Guide - Page 46
... or removed. You must replace the system board.
36 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
Setting the password override switch: The following illustration shows the location of the password override switch (switch 8 on switch block 1 on the system board) to ON.
4.
Install the server cover (see "Installing the cover" on page...
User Guide - Page 76
... and DC power LEDs are no serviceable parts inside any part that has the following label attached. Power supply bay 1 If you install an optional power supply in this label attached. There are on a power supply or any component that the power supply is operating properly.
66 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY...
User Guide - Page 90
...that you install this
80 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY Configuring the Ethernet controller
When you use the Ethernet controller. The controller supports half-... device drivers are provided on the Ethernet local area network (LAN).
You do not need to set any jumpers or configure the controller for redundant Ethernet
The IBM Netfinity...
User Guide - Page 91
... and the optional redundant NIC adapter is switched to upgrade the primary adapter hardware. even if it is installed in a hot-plug PCI slot, you can install in slot 2 (PCI bus A slot 2).
5. Note: If you hot replace the primary adapter while the Ethernet traffic is supported by the secondary Ethernet controller, the traffic does not...
User Guide - Page 97
... system network:
v Serial Connection Control
Use the Serial Connection Control service to use a Netfinity Manager system modem to establish a connection with any system that has an Internet connection and a World Wide Web (WWW) browser. Note: This section provides installation instructions for all operating systems supported by System Information Tool, System Profile, Software Inventory, and...
User Guide - Page 102
...v ECC Memory Setup (requires ECC memory) v Event Scheduler v File Transfer v Power On Error Detect
92 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY Network communication drivers and the following Netfinity Manager services are required by the installation configuration. The available installation options are:
v Advanced System Management Support
Click Advanced...
User Guide - Page 106
... to the system configuration files, and asks whether the installation program should make the changes. Netfinity Manager database support
Netfinity Manager supports the collection and export of a vast amount of these Netfinity Manager services: v Alert Manager v Software Inventory v System Information Tool
96 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY...
IBM 865811Y Reviews
We have not received any reviews for IBM yet.