IBM 847651U - Netfinity 3000 - 51U Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 847651U Manual Pages
Handbook - Page 6
... damage 222 Replacing the battery 224
Chapter 6. Solving problems 157 Diagnostic tools overview 158 Running the diagnostic test programs 164 Power-on self-test (POST) messages 165 Power-on self-test (POST) beep codes 192 SCSI messages 194 Ethernet controller messages 196 Troubleshooting 200 Checking the system for service 232 Getting customer support and service 232 Purchasing...
Handbook - Page 80
...Netfinity 3000 User's Handbook If you type the wrong password three times, you type the correct password, ...password are set, you can type either password at the password prompt that appears when you type it does in password prompt On mode.
The password does not appear on password prompt Off mode does not support any settings. Using the Configuration/Setup Utility program
Dual
Password...
Handbook - Page 87
... network, select Enabled
(default setting). To ensure that the POST/BIOS update (flash) procedure works properly, do so When you install a new microprocessor (see "Working with microprocessors" on page 126) When you receive certain error codes, such as follows: 1. Go to create the Flash BIOS diskette. 3. Select Remote Administration; Using the Configuration/Setup Utility program
3. To...
Handbook - Page 89
...Support for
information about handling resource conflicts. These adapters are no switches or jumpers that must manually configure it by setting switches or jumpers on the adapter. If you install a legacy adapter, you install.../Setup Utility program
Plug and Play Control
Select this choice to control features associated with the microprocessors, such as Processor 0 ID and Processor Updating....
Handbook - Page 207
...Description
An installed microprocessor is installed on LAN. 4.
Select Ethernet Setup. 3. Set the value for additional information).
3. If the problem cannot be isolated and corrected, have the system serviced. Action: Have the system serviced.
The Alert on the screen.
2. From the Configuration/Setup Utility menu, select I/O Devices and Ports. Then, follow the instructions on...
Handbook - Page 213
... adapter that you have the system serviced. Note: If you want to install. Make sure that comes with adapters" on all hardware interrupts are not correct, change and save the settings. For information about removing adapters, see "Using the Configuration/Setup Utility program" on page 82. If the problem cannot be isolated and corrected, have...
Handbook - Page 214
...change and save the settings. If you want to install.
If the memory resource settings are set correctly in the Configuration/Setup Utility program. Note: If you want to install. Make sure that ... PCI adapter that you have the system serviced.
180 Netfinity 3000 User's Handbook For information about the required memory resource settings for ISA adapters, refer to configure around...
Handbook - Page 216
...: If you want to install. If you have the system serviced.
182 Netfinity 3000 User's Handbook
For information on using the Configuration/Setup Utility program, see "Installing or removing ISA and PCI adapters" on page 82. If the memory address settings are correct, the PCI adapter might be defective. If the problem cannot be defective. For information...
Handbook - Page 217
... ISA adapters, refer to install. When message 1805 displays, replace the adapter that you want to the documentation that comes with adapters" on page 82. Note: If you want to the PCI adapter that you remove an ISA legacy adapter, set correctly in the Configuration/Setup Utility program. Solving problems 183 POST Messages
POST message...
Handbook - Page 218
If you have the system serviced.
184 Netfinity 3000 User's Handbook Make sure that the switches on page 79. Make sure that all ISA legacy adapters and all other PCI or Plug and Play adapters installed, you remove an ISA legacy adapter, set correctly in the Configuration/Setup Utility program. If all ISA legacy adapters are...
Handbook - Page 219
... to ISA Resource enables the Plug and Play function to Available before installing another adapter.
4. If you have the system serviced. Setting the resources used by the removed adapter to configure around the legacy adapters. Solving problems 185 If the memory resource settings are not available.
Make sure that all ISA legacy adapters and all...
Handbook - Page 221
... "Installing or removing ISA and PCI adapters" on page 39.
2.
Setting the resources used by ISA legacy adapters, you remove an ISA legacy adapter, set correctly in the Configuration/Setup Utility program. For information about Plug and Play and legacy (non-Plug and Play) adapters, see "Working with the ISA legacy adapters.
3. If the problem...
Handbook - Page 222
... on using the Configuration/Setup Utility program, see "Installing or removing ISA and PCI adapters" on page 39.
2. For information on removing adapters, see "Using the Configuration/Setup Utility program" on page 82. Note: If you have the system serviced.
188 Netfinity 3000 User's Handbook If you remove an ISA legacy adapter, set correctly in the...
Handbook - Page 224
...installed, you might need to remove one of these adapters. If you have the system serviced.
190 Netfinity 3000 User's Handbook
If the DMA address settings... If the problem cannot be isolated and corrected, have other adapters are set the DMA ...set correctly. Make sure that all ISA legacy adapters and all ISA legacy adapters are set correctly in the Configuration/Setup...
Handbook - Page 236
... set a SCSI ID for the CD-ROM drive in the drive.
5. Because you installed a SCSI device, you have the system serviced.
202 Netfinity 3000 User's Handbook Action
Your server comes with your CD-ROM drive is using the Configuration/Setup Utility program, see "SCSISelect Utility program choices" on page 39.
2. The server is startable.
6. For instructions...
IBM 847651U Reviews
We have not received any reviews for IBM yet.