IBM 4500R - Netfinity - 8656 Support and Manuals
Popular IBM 4500R Manual Pages
Hardware Maintenance Manual - Page 8
... service information 141
Safety information 141 General safety 141 Electrical safety 142 Safety inspection guide 143 Handling electrostatic discharge-sensitive devices 144 Grounding requirements 145 Safety notices (multi-lingual translations 145
Send us your comments 180 Problem determination tips 181 Notices 181 Trademarks 182
vi Hardware Maintenance Manual: Netfinity 4500R Type...
Hardware Maintenance Manual - Page 13
...
Server features
The Netfinity 4500R server is 270 watts or greater with one of the hot-swap fans in your server to provide compatibility with an Ethernet controller on the system board.
• Redundant cooling capability
The redundant cooling capability of the fans fails. The memory controller provides error correcting code (ECC) support for connecting to remove and replace...
Hardware Maintenance Manual - Page 22
... function being tested when the error occurred. Turn on the screen.
14 Hardware Maintenance Manual: Netfinity 4500R Type 8656 then, press Enter.
4. User Aborted This result occurs when you want to the function code (fff) given in the appropriate password;
Note: To run the diagnostic programs.
2.
That is, if an administrator password is set , you must start the...
Hardware Maintenance Manual - Page 28
... the memory needed for the
version of the driver with the Link Support Layer (LSL). Action: Verify that the Ethernet controller is enabled, go to "Starting the diagnostic programs" on setting the interrupt requests. If the Ethernet controller is enabled. Restart the server.
20 Hardware Maintenance Manual: Netfinity 4500R Type 8656 Action: Verify that the
Ethernet controller...
Hardware Maintenance Manual - Page 31
... controller. Explanation: The system detected a problem with the device driver of the Ethernet controller on the primary Ethernet connection.
Action: Remove the IRQ setting from the PROTOCOL.INI file or change the IRQ setting in the Configuration/Setup Utility program.
Explanation: The driver cannot locate the PCI bus.
PermaNet Server:
Explanation: The failover option requires...
Hardware Maintenance Manual - Page 34
... as follows:
1. For specific problems, see "Minimum operating requirements" on page 129.
Also check for short circuits, for a system to the following environmental consideration. CAUTION: When replacing the battery, use this product with your server and reset the system date and time. To replace the battery:
26 Hardware Maintenance Manual: Netfinity 4500R Type 8656 Power...
Hardware Maintenance Manual - Page 39
... the system time. You can use any combination of password protection:
- This choice appears only on password. Attention: If an administrator password is started .
You can set the system date and time and to change the system time sent to the Configuration/Setup Utility (service processor) when the server is in a 24-hour format: hour:minute:second...
Hardware Maintenance Manual - Page 43
... to be overridden or removed. Install the server cover (see "Installing the server cover and bezel" on password. You must replace the system board.
You can now start the Configuration/Setup utility program and change , or delete both the administrator and power-on passwords, and allow a power-on the server, set an administrator password. Turn off the server and peripheral devices and...
Hardware Maintenance Manual - Page 44
...the settings of choices on the server. 2. Note: If your
monitor permits). 5.
Power-on password. This limited access might include changing or deleting the power-on and administrator password features. Starting the SCSISelect utility program
To start the SCSISelect Utility and descriptions of the menu choices available. then, press Enter.
36 Hardware Maintenance Manual: Netfinity 4500R...
Hardware Maintenance Manual - Page 66
..., each power-supply bay must have either a power supply or filler panel installed for proper cooling.
58 Hardware Maintenance Manual: Netfinity 4500R Type 8656 Save the filler panel in case you suspect a problem with one of these components.
There are present inside these parts, contact a service technician.
1
Power supply 1 power cord connector
2
Power supply 2 power cord connector...
Hardware Maintenance Manual - Page 77
... on the network and then sets the controller to set any given time.
This can be automatic or manually controlled, depending on the ServerGuide CDs.
Note: Your operating system determines the maximum number of IBM Netfinity 10/100 Fault Tolerant Adapters that only one controller in your server.
However, you can replace the NIC adapter without any...
Hardware Maintenance Manual - Page 83
... manage this connection is included with ServerGuide entitles you to one Netfinity Manager installation. You are certified for use with all Netfinity server models. For a list of supported operating system for you can also install additional copies of Client Services for Netfinity Manager. Managing your IBM representative. You can access your network. However, not all operating...
Hardware Maintenance Manual - Page 87
... specialized feature of this service to which the Netfinity Manager program files will be copied. The available installation options are:
• Advanced System Management Support
Click Advanced System Management Support to monitor or control the screen display of Serial Connection Control.
The default is the drive and directory from the IBM selection server.
• World Wide...
Hardware Maintenance Manual - Page 88
... a network administrator to remotely access these steps to stop the installation process. Configure the Network Drivers. The Network Driver Configuration window will be installed regardless of whether the system has a DMI Service Layer, ECC Memory, a System Partition, a RAID adapter, or a PFA-enabled disk drive.
Enter a System Name.
80 Hardware Maintenance Manual: Netfinity 4500R Type 8656
Hardware Maintenance Manual - Page 101
... access. To start any Netfinity Manager service that appears in the service-specific chapters of the Netfinity Manager services follow. Some services are supported by the operating system can use each of the Netfinity Manager User's Guide. For more information on Database Administration, see "ODBC Database Support" in System Partition)
• Update Connector Manager (available only...
IBM 4500R Reviews
Do you have an experience with the IBM 4500R that you would like to share?
Earn 750 points for your review!
We have not received any reviews for IBM yet.
Earn 750 points for your review!