Owners Manual
Page 2
...; Never add fuel to be stored for the cause. PREPARATION • Thoroughly inspect the area where the equipment is in safe working condition. • Check shear pins, engine mounting bolts, and other safety protective devices in place. • Keep children and pets away. • Do not overload the machine capacity by manufacturer...
...; Never add fuel to be stored for the cause. PREPARATION • Thoroughly inspect the area where the equipment is in safe working condition. • Check shear pins, engine mounting bolts, and other safety protective devices in place. • Keep children and pets away. • Do not overload the machine capacity by manufacturer...
Owners Manual
Page 4
... Bolt 3/8-16 UNC x 1 Grade 5 (1) Center Locknut 3/8-16 UNC (1) Flat Washer 13/32 x 1 x 11 Gauge (1) Handle Lock Lever (1) Hairpin Clip (1) Pivot Bolt 3/8-16 UNC Grade 5 Extra Shear Pins & Clips 4 ASSEMBLY Your new tiller has been assembled at the factory with exception of pliers (1) 9/16" wrench FRONT LEFT RIGHT OPERATOR'S POSITION (See Fig. 1) When...
... Bolt 3/8-16 UNC x 1 Grade 5 (1) Center Locknut 3/8-16 UNC (1) Flat Washer 13/32 x 1 x 11 Gauge (1) Handle Lock Lever (1) Hairpin Clip (1) Pivot Bolt 3/8-16 UNC Grade 5 Extra Shear Pins & Clips 4 ASSEMBLY Your new tiller has been assembled at the factory with exception of pliers (1) 9/16" wrench FRONT LEFT RIGHT OPERATOR'S POSITION (See Fig. 1) When...
Owners Manual
Page 17
NEW TINE WORN TINE tine_19 Fig. 26 SHARP EDGES TINE TINE Fig. 27 3-1/2" MAX HAIRPIN CLIP SHARP EDGES HAIRPIN CLIP SHARP EDGES SHEAR PIN Fig. 28 17 tine_20 A tine this worn needs to be replaced. • To maintain the superb tilling performance of this machine the tines should be ...
NEW TINE WORN TINE tine_19 Fig. 26 SHARP EDGES TINE TINE Fig. 27 3-1/2" MAX HAIRPIN CLIP SHARP EDGES HAIRPIN CLIP SHARP EDGES SHEAR PIN Fig. 28 17 tine_20 A tine this worn needs to be replaced. • To maintain the superb tilling performance of this machine the tines should be ...
Owners Manual
Page 20
...Ground too wet. 1. Engage drive control. 2. Carburetor out of adjustment. 13. Set depth stake for more favorable soil conditions. Shear pin(s) broken. 1. Hard to shift gears. Briefly engage tine control and release or rock tiller forward and backward until are not engaged... plug wire. 10. Contact an authorized service center department. 1. Adjust carburetor to start CAUSE 1. Inspect/adjust V-belt. 3. Replace shear pin(s). Throttle control not set in between counter rotating till position and forward rotating till position. 2. Clean engine air screen. 3. Soil ...
...Ground too wet. 1. Engage drive control. 2. Carburetor out of adjustment. 13. Set depth stake for more favorable soil conditions. Shear pin(s) broken. 1. Hard to shift gears. Briefly engage tine control and release or rock tiller forward and backward until are not engaged... plug wire. 10. Contact an authorized service center department. 1. Adjust carburetor to start CAUSE 1. Inspect/adjust V-belt. 3. Replace shear pin(s). Throttle control not set in between counter rotating till position and forward rotating till position. 2. Clean engine air screen. 3. Soil ...
Parts Manual
Page 7
REPAIR PARTS TILLER - - DESCRIPTION 8 874 61 06-16 Bolt, Hex 3/8-24 x 1 16 532 16 34-99 Tine, Spade 17 532 16 35-00 Tine, Cleaning NOTE: All component dimensions given in U.S. NO. DESCRIPTION 2 532 13 26-73 Pin, Shear 4 532 00 31-46 Clip, Hairpin 5 532 18 88-45 Hub Assembly 6 873 61 06-00 Nut, Hex 3/8-24 7 810 04 06-00 Washer, Lock 3/8 KEY PART NO. NO. MODEL NUMBER DRT900 (96093001802), PRODUCT NUMBER 960 93 00-18 TINE ASSEMBLY KEY PART NO. inches. 1 inch = 25.4 mm 7
REPAIR PARTS TILLER - - DESCRIPTION 8 874 61 06-16 Bolt, Hex 3/8-24 x 1 16 532 16 34-99 Tine, Spade 17 532 16 35-00 Tine, Cleaning NOTE: All component dimensions given in U.S. NO. DESCRIPTION 2 532 13 26-73 Pin, Shear 4 532 00 31-46 Clip, Hairpin 5 532 18 88-45 Hub Assembly 6 873 61 06-00 Nut, Hex 3/8-24 7 810 04 06-00 Washer, Lock 3/8 KEY PART NO. NO. MODEL NUMBER DRT900 (96093001802), PRODUCT NUMBER 960 93 00-18 TINE ASSEMBLY KEY PART NO. inches. 1 inch = 25.4 mm 7