Husqvarna 395 XP W Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna 395 XP W manuals!
Problems with Husqvarna 395 XP W?
Ask a Question
Free Husqvarna 395 XP W manuals!
Problems with Husqvarna 395 XP W?
Ask a Question
Popular Husqvarna 395 XP W Manual Pages
Owners Manual - Page 2
... injury.
You should automatically set the stop switch to the start position. WARNING! English Please read the operator's manual carefully and make starting the machine. Regular cleaning is to operate the chain saw holding it with one hand only. Visual check. Refuelling.
Decompression valve: The valve is required.
Never let the guide bar tip come in...
Owners Manual - Page 4
... equipment 11 ASSEMBLY Fitting the bar and chain 17 FUEL HANDLING Fuel 18 Fueling 19 Fuel safety 19 STARTING AND STOPPING Starting and stopping 20 WORKING TECHNIQUES Before use 22 General working instructions 22 How to avoid kickback 28 MAINTENANCE Carburetor adjustment 30 Checking, maintaining and servicing chain saw safety equipment 31 Muffler 33...
Owners Manual - Page 5
... or sell this operator′s manual as for production of your nearest servicing dealer. For customer assistance, contact us at our website: www.usa.husqvarna.com
English - 5 Congratulations on a tradition that it is working today. In 1956, the first motor driven lawn mowers appeared, followed by chain saws in the world of the...
Owners Manual - Page 6
...?
24
Husqvarna XXXX
XXXX XXXXXXX
Husqvarna AB Huskvarna, SWEDEN
22 6 5
4
12 3
12 21
11
20 19 18 17 16 15 14 13
28 7 8 27 9
10
25 23
26
What is what on the chain saw?
1 Cylinder cover 2 Front handle 3 Front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws carburetor 8 Choke control/Start throttle...
Owners Manual - Page 7
... non- authorized accessories or replacement
parts.
See instructions under the headings Fuel Handling and Starting and Stopping.
• Do not use any accessories other than those recommended in a
! loaded stop switch and can result in the chapter Technical data. Carry out the checks, maintenance and service instructions described in this manual carefully.
• Check that...
Owners Manual - Page 12
...the spacing of replacement bar and chain combinations we recommend, and follow the filing
instructions. Chain A chain is to make sure that describe the bar and chain
To maintain the...
English No saw
chain increases the risk of kickback.
• Maintain the correct depth gauge setting! If the chain is slack it is determined by Husqvarna. See instructions under the
heading...
Owners Manual - Page 14
... correct depth gauge setting for your particular chain. Use the flat the same time. The depth gauge setting is worn out and should be replaced. See instructions under the heading ...setting
WARNING! This recommendation assumes that you adjust the depth gauge setting every third time you cannot pull it becomes. Tensioning the chain
General advice on our chain saws varies from model...
Owners Manual - Page 18
...Chain oil
• We recommend the use oil intended for all engines. Always ensure there is recommended.
This results in a clean container intended for fuel.
• Always start...as set out...HUSQVARNA two-stroke engine oil, which can occur. The machine is equipped with catalytic converters means that only unleaded gasoline can drastically affect the ratio of fuel (see instructions...
Owners Manual - Page 24
..., i.e.
When you replace the bar and chain use full throttle when cutting!
• Reduce the speed to idle after cutting.
4 Is there a risk of kickback?
9 Follow the instructions on sharpening and maintaining...support. Cutting with the top edge of the
bar, i.e. Basic cutting technique
WARNING! The chain tries to push the chain saw back towards the tree and the front edge of the chain...
Owners Manual - Page 25
... most cases you can avoid these problems by piece.
1
2
3
If it will touch the ground when you finish the cut pieces from the bottom. The log is a high risk that you are likely to cut and free the chain saw free. Cutting
WARNING!
There is supported at both ends. There is possible...
Owners Manual - Page 30
... from you and so that air is admitted, which is essential to the starting instructions and let it has
been properly adjusted or repaired. Correct adjustment is controlled with movement limiters on the carburetor adjuster screws. dealer, if the idle speed setting cannot be finely adjusted. Adjusting the carburetor while a dirty air fi...
Owners Manual - Page 31
....
Do not use the chain saw safety equipment
Note! If your servicing
! Correctly adjusted carburetor
When the carburetor is set too lean it has
been properly adjusted or repaired. Contact your machine fails any wood dust, resin and dirt from the chain brake and clutch drum. speed.
If it may cause starting difficulties and...
Owners Manual - Page 35
...spark plug should be replaced with different types of engine power • Unnecessary wear to engine parts • Excessive fuel...conditions, weather, season, etc. Always use for advice.
A HUSQVARNA chain saw can be cleaned more thoroughly by brushing or shaking it...out the starter cord and place the starter in operating problems and starting difficulties. Clean the filter by ...
Owners Manual - Page 40
...have extraordinary cutting needs and experience
and specialized training for this model we recommend the following cutting equipment. Saw chain filing and file gauges
40 - in ...H47
H42
H48
H45
H50
WARNING!
TECHNICAL DATA
Recommended original and replacement bar and chain combinations
The Husqvarna 395XP is in the ANSI category of severe kickback that could result in...
Owners Manual - Page 41
... TO GET WARRANTY SERVICE
Warranty services or repairs shall be provided at no abuse, neglect or improper maintenance of a warranted part still under warranty. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement part used in your failure to ensure the performance of receipts or for replacement as a problem exists. MANUFACTURER...
Husqvarna 395 XP W Reviews
We have not received any reviews for Husqvarna yet.