Hunter 20431 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 20431 manuals!
Problems with Hunter 20431?
Ask a Question
Free Hunter 20431 manuals!
Problems with Hunter 20431?
Ask a Question
Popular Hunter 20431 Manual Pages
Installation Guide - Page 1
... or support brace that both the inner and outer holes in accordance with national and local electrical codes and ANSI/NFPA 70. Preparing the Fan Site
8' Minimum Ceiling Height
7' Minimum to Floor
30" From Wall or Nearest Obstruction
Step 1 Choose the Fan Site
Proper ceiling fan location and attachment to your fan manual and begin with 2 • Installing the Ceiling Plate...
Owner's Manual - Page 1
Date Purchased
Where Purchased
Type 2 Models
Owner's Guide and Installation Manual
English
Form# 42631-01 20081013 ©2008 Hunter Fan Co.
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Catalog No. Model Name
Model No.
Owner's Manual - Page 2
... with the best ceiling fan available anywhere in accordance with wiring, use a qualified electrician. • To reduce the risk of the building according to the outlet box and associated wall switch location. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the
support structure of...
Owner's Manual - Page 3
...or Angled mounting. Support Brace
Ceiling Outlet Box
For ceilings higher than 8 feet high
CAUTION: To reduce the risk of personal injury, attach the fan directly to these instructions, and use only Hunter speed controls.
For quiet and optimum performance of your Hunter fan in this manual include instructions for ceilings less than 8 feet, you maximum installation flexibility and...
Owner's Manual - Page 4
... call Hunter Technical Support Department at 888-830-1326. 1 • Getting Ready
To install a ceiling fan, be sure you are installing more than one fan, keep the fan blades and blade irons (if applicable) in sets, as they were shipped.
4 42631-01 • 10/13/08 • Hunter Fan Company
Proper ceiling fan location and attachment to the fan parts. Check for installing the fan...
Owner's Manual - Page 5
... installing your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as a tag, to the service panel.
2-1.
Note: The isolators should be flush against the ceiling. 2-6.
Check to the outlet box and associated wall switch location. Ceiling Plate
3" Wood Screw
Steps 2-3 - 2-6
5 42631-01 • 10/13/08 • Hunter Fan Company...
Owner's Manual - Page 6
...one side of the pin in these installation instructions.
3-1. this coating; Skip to hang the fan. the coating prevents the downrod from the fan through the canopy and canopy trim ring...8226; 10/13/08 • Hunter Fan Company
Do not remove this is replaced with the
low profile washer. 3-4. Note: When the pipe and ball assembly is fully installed, 2-3 threads on the threads....
Owner's Manual - Page 7
... accordance with national and local electrical codes and ANSI/NFPA 70. Before attempting installation, make sure the power is still off. 4-2. Connect the bare or green ground wire (grounded) from the ceiling to the green ground wire (grounded) from the ceiling plate and the green ground wire from the fan. 4-5. Spread the wires apart, with...
Owner's Manual - Page 8
... the ceiling plate tabs.
5-4.
Swing the fan up with the mounting holes on the ceiling plate. Holding the canopy up to align the canopy screw holes with the screw holes aligned, partially install two canopy... 5-3 Canopy Canopy Trim Ring
Canopy Screw
8 42631-01 • 10/13/08 • Hunter Fan Company Rotate the hanger ball so the tab in the canopy is recommended you need to the ...
Owner's Manual - Page 9
...
Use with grommet
Blade Assembly Screws
Steps 6-1 - 6-2
Use without grommet
Blade Mounting
Screw
Step 6-4
9 42631-01 • 10/13/08 • Hunter Fan Company Insert the second blade mounting screw, then securely tighten both mounting screws. This is normal.
6-3. Your fan may appear slightly loose after screws are installed in the motor to the...
Owner's Manual - Page 10
... the lower switch housing to the product.
7-5. To attach the upper switch housing, partially install two #6-32 x
3/8" housing assembly screws into the housing. Align the side screw holes ...; 10/13/08 • Hunter Fan Company Tighten all three assembly screws could cause improper operation and damage to the upper switch housing with this fan model. 7-1. Turn the housing counterclockwise...
Owner's Manual - Page 11
..., this ceiling fan contains a device that limit or the marked limit on this product may vary. 7-6. Exceeding that restricts the light kit to the light fixture. Raise the shade to a maximum of lights may result in fire hazard or improper operation.
11 42631-01 • 10/13/08 • Hunter Fan Company
Install B10 candelabra...
Owner's Manual - Page 12
...settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent scratching. 8 • Operating and Cleaning Your Ceiling Fan
8-1. Ceiling fans...with a direct breeze. Restart fan. Reversing Switch
12 42631-01 • 10/13/08 • Hunter Fan Company The fan pull chain controls power to the fan.
8-2. If this happens,...
Owner's Manual - Page 13
... type of light bulbs installed match the specifications on . 6. Check the plug connection in the switch housing. 4. Pull the pull chain to see if the blade is engaged. 5. Problem: Noisy operation. 1. Turn power off, support fan very carefully, and check that the switch is cracked. Check to the wiring the fan section. 3.
Hunter Fan Company 2500 Frisco Avenue...
Parts Guide - Page 1
... bulb / Bulb Globe/Shade
Model # Asm. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Dwg. #
20430A 94294-01
20431A 94294-02
20434A 94294-03
20436A 94294-04
20438 94294-06
Finish
Qnty 1
Antique Brass Brushed Nickel Bright Brass
Part # 96759-05
Part # 96759-09
Part # 96759-01
White
Part # 96759-03
New Bronze
Part # 96759-30
1
93598-01...
Hunter 20431 Reviews
We have not received any reviews for Hunter yet.