Honeywell T8002 Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell T8002 manuals!
Problems with Honeywell T8002?
Ask a Question
Free Honeywell T8002 manuals!
Problems with Honeywell T8002?
Ask a Question
Most Recent Honeywell T8002 Questions
No Cool Air After Power Outage
I had a power outage yesterday - 2 outages for about 30 seconds each. Since then, the fan on the AC ...
I had a power outage yesterday - 2 outages for about 30 seconds each. Since then, the fan on the AC ...
(Posted by scarlettellers 9 years ago)
Popular Honeywell T8002 Manual Pages
Owner's Manual - Page 2
... of heating or air conditioning. When you follow the simple programming instructions in this manual, your thermostat automatically controls the temperature in event of comfort and energy savings with reliable, precise temperature control. Features
• Program up to four time periods with temperature settings to the world of power failure.
• Indefinite temperature hold...
Owner's Manual - Page 3
... ...6 Programming Thermostat ...7
Setting Current Time and Day ...8 Setting Weekday Program ...9 Setting Weekend Program ...10 Setting Temporary Temperature Hold 13 Setting Indefinite Temperature Hold 13 Operating Thermostat ...13 Setting SYSTEM and FAN Switches 13
Replace the Batteries (T8002 Only 14 Backlighting (Select Models 14 Minimum Off-Timing ...15 Troubleshooting ...16 Customer...
Owner's Manual - Page 4
.... BATTERY DOOR
SYSTEM SWITCH
M14673
4
69-1431-1
Key Locations and Descriptions
INCREASE ▲ KEY
• PROGRAM TIME AND TEMPERATURE. • SET TEMPORARY...SET TEMPORARY TEMPERATURE HOLD.
INCREASE ▲ KEY • PROGRAM TIME AND TEMPERATURE. • SET TEMPORARY TEMPERATURE HOLD. T8000, T8001
PM
T8011, T8024
TUE
MODELS
Hold
Select
PM TUE
Hold
Select
T8002 MODEL...
Owner's Manual - Page 6
The temperatures cannot be set any higher than 99°F (37°C) or any lower than 40°F (4°C).
6
69-1431-1 Program Schedule
Weekday
Start Time
Heating Temperature
Cooling Temperature
...
Owner's Manual - Page 8
... programming mode.
M18534
To use the preprogrammed time and temperature (see Table 1), press Hold to set current day. M12591A
8
69-1431-1 To set day of week, press Select again. Sharp instruments like pens and pencil points can set for an energy-saving temperature while you can damage the keyboard. Press ▲ or ▼...
Owner's Manual - Page 10
...Press Select. Press Select. Press Select. Press ▲ or ▼ to set
Sleep
SET
time. M18569
b. erature. Press ▲ or ▼ to set Return SET temperature.
6. Press Select. Press ▲ or ▼ to set
Sleep
SET
temp- Press ▲ or ▼ to set
Wake
SET
time. erature.
M12633C
M12631C
10
69-1431-1 b. Sleep
M12629B
a.
Wake a. Press...
Owner's Manual - Page 13
... off.
Slide the SYSTEM switch in the lower left corner of the thermostat to select the desired fan setting. Ht. (heat pump models only): The thermostat cycles emergency heat relay (E) and cycles auxiliary heat (W2), as needed, to control thermostat operation.
Operating Thermostat
Setting SYSTEM and FAN Switches
Use the SYSTEM and FAN switches to maintain setpoint...
Owner's Manual - Page 14
... the current time and day. Your program does not require resetting; The message flashes for approximately ten seconds. Important: Even if you insert the batteries within approximately 30 seconds of battey power.
14
69-1431-1
Replacing the Batteries (T8002 Models Only)
The T8002 Thermostat requires three AA alkaline batteries to prevent leakage and/or the heating/cooling system from...
Owner's Manual - Page 15
... or cooling on again for at least five minutes after it turns off. The minimum off-timer operates in cooling on the T8000 and T8001, T8002, T8024 (multistage model) and in effect.
15
69-1431-1 Power interruption and power restoration also trigger the minimum off -timer is changed . If the compressor turns off...
Owner's Manual - Page 16
... thermostat is in the Off
position-set the heating higher or the cooling lower).
continued
16
69-1431-1 Temperature settings do not change (example: cannot set to the On position. • Check if the batteries are good and installed correctly
(T8002 only).
• Check that the temperature setpoints are: between 40 to 99°F (4 to 37°C).
Troubleshooting...
Owner's Manual - Page 17
... breaker is tripped-reset the circuit breaker.
• Check if the fuse is blown-replace the fuse. • Check if the switch at the equipment is in the Off
position-set to Heat. • If the temperature setting is higher than the current room
temperature and the flame is displaying, the thermostat is operating correctly...
Owner's Manual - Page 18
... thermostat is operating correctly.
Action
• Check if the circuit breaker is tripped-reset the circuit breaker.
• Check if the fuse is blown-replace the fuse. • Check if the switch at the equipment is in the Off
position-set to On position. • Wait five minutes for assistance. continued
18
69-1431-1 Troubleshooting...
Owner's Manual - Page 19
Troubleshooting (Continued).
System on indicator
or is lit, but no warm or cool air is in effect.
Action...is coming from the registers. Customer Assistance
If you have any questions concerning the operation of your thermostat, please visit us at www.honeywell.com or call the thermostat information helpline at 1-800-468-1502.
19
69-1431-1 Symptom System on indicator
or is complete....
Owner's Manual - Page 20
... warranty shall not apply if it is defective or malfunctions, Honeywell shall repair or replace it (at any time during the warranty period, the product is shown by Honeywell that the defect or malfunction was in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase...
Owner's Manual - Page 21
This warranty gives you specific legal rights, and you may not apply to you. Some states do not allow ...OF THIS WARRANTY. In Canada, write Retail Products ON15, Honeywell Limited/ Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
21
69-1431-1 Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above limitation may have...
Honeywell T8002 Reviews
We have not received any reviews for Honeywell yet.