Installation Guide
Page 1
...tapping screws (provided) in the control's cabinet, it to the raised tabs at the back of "0". CE For CE installations ADEMCO N6361 EMI suppression bead is supervised so that accompanies the module to the inside of the module's housing permit it need not be...its lower position. See the control's installation and setup guide for wire routing instructions. 1. N8924V1 5/01 Rev. B 4219 Wired Zone Expander Module INSTALLATION AND SETUP GUIDE GENERAL INFORMATION This module adds up to mount the 4219 before proceeding. 2. Refer to the Installation and Setup Guide for that is ...
...tapping screws (provided) in the control's cabinet, it to the raised tabs at the back of "0". CE For CE installations ADEMCO N6361 EMI suppression bead is supervised so that accompanies the module to the inside of the module's housing permit it need not be...its lower position. See the control's installation and setup guide for wire routing instructions. 1. N8924V1 5/01 Rev. B 4219 Wired Zone Expander Module INSTALLATION AND SETUP GUIDE GENERAL INFORMATION This module adds up to mount the 4219 before proceeding. 2. Refer to the Installation and Setup Guide for that is ...
Installation Guide
Page 2
... TERMINATE EACH PROGRAMMED ZONE WITH 1000 OHM END-OF-LINE RESISTOR (EACH ZONE'S MAX. ON - CONSULT CONTROL'S INSTRUCTIONS FOR ADDRESS USE. ON - ON - LOOP RESISTANCE: 300 OHMS + EOL) 4219-SOC-V0 © 12 3 4 5 OFF ON © © © © SWITCH NUMBER 4219 ADDRESS SETTINGS ("-"means... ON ON ON ON ON ON ON ON DIP SWITCH: (WHITE AREAS DENOTE SWITCH HANDLES) POSITIONS 2-5: DETERMINE ZONE EXPANDER'S ADDRESS. REED (TAMPER) SWITCH TAMPER JUMPER POSITION 4219 IN CABINET (NOT TAMPER) 4219 REMOTE (TAMPER PROTECTED) 4-PIN CONSOLE PLUG CONNECTIONS SAME AS TB2 TB1 1 2 3 4 5 6 7 ...
... TERMINATE EACH PROGRAMMED ZONE WITH 1000 OHM END-OF-LINE RESISTOR (EACH ZONE'S MAX. ON - CONSULT CONTROL'S INSTRUCTIONS FOR ADDRESS USE. ON - ON - LOOP RESISTANCE: 300 OHMS + EOL) 4219-SOC-V0 © 12 3 4 5 OFF ON © © © © SWITCH NUMBER 4219 ADDRESS SETTINGS ("-"means... ON ON ON ON ON ON ON ON DIP SWITCH: (WHITE AREAS DENOTE SWITCH HANDLES) POSITIONS 2-5: DETERMINE ZONE EXPANDER'S ADDRESS. REED (TAMPER) SWITCH TAMPER JUMPER POSITION 4219 IN CABINET (NOT TAMPER) 4219 REMOTE (TAMPER PROTECTED) 4-PIN CONSOLE PLUG CONNECTIONS SAME AS TB2 TB1 1 2 3 4 5 6 7 ...
Installation Guide
Page 3
...free from defects in materials and workmanship under normal use and service for 24 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which is proved not in compliance with its option, free of charge for 12... Seller's specifications or proves defective in materials or workmanship under normal use and service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791. that the product(s) it is the only warranty made by burglary, robbery, fire...
...free from defects in materials and workmanship under normal use and service for 24 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which is proved not in compliance with its option, free of charge for 12... Seller's specifications or proves defective in materials or workmanship under normal use and service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791. that the product(s) it is the only warranty made by burglary, robbery, fire...
Installation Guide
Page 4
...; Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from the U.S. www.honeywell.com/security The FCC requires the following statement for use. If necessary, the user should consult the dealer or an experienced radio/...television technician for Class B computing device in accordance with the manufacture's instructions, may find the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving...
...; Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from the U.S. www.honeywell.com/security The FCC requires the following statement for use. If necessary, the user should consult the dealer or an experienced radio/...television technician for Class B computing device in accordance with the manufacture's instructions, may find the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving...