Instruction Manual
Page 9
....131" (3.3 mm) . 090" (2.3 mm) .111" (2.8 mm) Dimensions of nails Nails are collated and coiled, as shown in the Table below can be driven with this Nailer. Max. .245" (6.2 mm) .266" (6.8 mm) NV50A1 Min. STANDARD ACCESSORIES 1 Model 1 Eye protector ...Hitachi nails to malfunction and resulting injuries. Max. .236" (6 mm) .283" (7.2 mm) NV65AC Min. ACCESSORIES .083" (2.1 mm) .083" (2.1 mm) Wire-collated coil nails WARNING ⅷ Accessories other than those shown below can lead to assure nail quality and driving ease. English SPECIFICATIONS Model NV83A2 NV65AC...
....131" (3.3 mm) . 090" (2.3 mm) .111" (2.8 mm) Dimensions of nails Nails are collated and coiled, as shown in the Table below can be driven with this Nailer. Max. .245" (6.2 mm) .266" (6.8 mm) NV50A1 Min. STANDARD ACCESSORIES 1 Model 1 Eye protector ...Hitachi nails to malfunction and resulting injuries. Max. .236" (6 mm) .283" (7.2 mm) NV65AC Min. ACCESSORIES .083" (2.1 mm) .083" (2.1 mm) Wire-collated coil nails WARNING ⅷ Accessories other than those shown below can lead to assure nail quality and driving ease. English SPECIFICATIONS Model NV83A2 NV65AC...
Instruction Manual
Page 11
... Nailer. 5. Air hose Air hose must remove all nails from the Nailer when disconnected. Air consumption table psi Operating pressure (bar) (kgf/cm2) 80 (5.5) (5.6) Air consumption ft3/cycle (ltr/cycle) NV83A2 .062 (1.8) NV65AC...plug at the air inlet. The lowered air pressure will cause the Nailer to ANSI Z87.1 specifications. 3. If abnormal operation occurs, stop using the check list below.... the air inlet. Keep the Nailer in a warm area until beginning the work , test the Nailer by using the Nailer and contact a Hitachi authorized service center immediately. - 11...
... Nailer. 5. Air hose Air hose must remove all nails from the Nailer when disconnected. Air consumption table psi Operating pressure (bar) (kgf/cm2) 80 (5.5) (5.6) Air consumption ft3/cycle (ltr/cycle) NV83A2 .062 (1.8) NV65AC...plug at the air inlet. The lowered air pressure will cause the Nailer to ANSI Z87.1 specifications. 3. If abnormal operation occurs, stop using the check list below.... the air inlet. Keep the Nailer in a warm area until beginning the work , test the Nailer by using the Nailer and contact a Hitachi authorized service center immediately. - 11...
Instruction Manual
Page 14
... nail holder to align the mark with finger. Insert the first nail into the magazine. NAILER OPERATION Read section titled "SAFETY" (pages 4 - 7). Driving Hole Guide Slot FirstNail ...of the nail holder according to ANSI Z87.1 specifications. Otherwise, the nail guide will not feed smoothly if the ...holder is forcibly closed . (7) Lock the knob completery. Fit the nail heads in the magazine, adjust the plate. Nail - 14 - English (1) ...correctly, the nail holder may be damaged. (3) Place the nail coil into the magazine opening. Press the knob down and swing the nail...
... nail holder to align the mark with finger. Insert the first nail into the magazine. NAILER OPERATION Read section titled "SAFETY" (pages 4 - 7). Driving Hole Guide Slot FirstNail ...of the nail holder according to ANSI Z87.1 specifications. Otherwise, the nail guide will not feed smoothly if the ...holder is forcibly closed . (7) Lock the knob completery. Fit the nail heads in the magazine, adjust the plate. Nail - 14 - English (1) ...correctly, the nail holder may be damaged. (3) Place the nail coil into the magazine opening. Press the knob down and swing the nail...
Instruction Manual
Page 18
... (See page 19) - 18 - C: No. SERVICE AND REPAIRS WARNING ⅷ Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer. ⅷ Use only parts supplied or recommended by an Hitachi Authorized Service Center. NOTE: Specifications are constantly being improved and modified to incorporate the latest technological advancements. Service parts list A: Item...
... (See page 19) - 18 - C: No. SERVICE AND REPAIRS WARNING ⅷ Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer. ⅷ Use only parts supplied or recommended by an Hitachi Authorized Service Center. NOTE: Specifications are constantly being improved and modified to incorporate the latest technological advancements. Service parts list A: Item...