Specifications
Page 1
H Global Storage Technologies 7K200 SATA OEM Specification Hard Disk Drive Specification Hitachi Travelstar 7K200 2.5 inch SATA hard disk drive Models: Revision 1.0 HTS722020K9A300 HTS722016K9A300 HTS722012K9A300 HTS722010K9A300 HTS722080K9A300 HTS722020K9SA00 HTS722016K9SA00 HTS722012K9SA00 HTS722010K9SA00 HTS722080K9SA00 10 May 2007 1/173
H Global Storage Technologies 7K200 SATA OEM Specification Hard Disk Drive Specification Hitachi Travelstar 7K200 2.5 inch SATA hard disk drive Models: Revision 1.0 HTS722020K9A300 HTS722016K9A300 HTS722012K9A300 HTS722010K9A300 HTS722080K9A300 HTS722020K9SA00 HTS722016K9SA00 HTS722012K9SA00 HTS722010K9SA00 HTS722080K9SA00 10 May 2007 1/173
Specifications
Page 10
... 1 Introduction This document describes the specifications of the HITACHI Travelstar 7K200, a 2.5-inch hard disk drive with Serial ATA interface: Drive name Travelstar 7K200-200 Model Number HTS722020K9A300 HTS722020K9SA00 MAX Data transfer rate (Gbps) 3.0 1.5 Capacity (GB) 200 Height (mm) Rotation speed (rpm) 9.5 7200 Travelstar 7K200-160 HTS722016K9A300 HTS722016K9SA00 3.0 160 9.5 7200 1.5 Travelstar 7K200-120 HTS722012K9A300 HTS722012K9SA00 3.0 120 9.5 7200 1.5 Travelstar 7K200-100 HTS722010K9A300 HTS722010K9SA00 3.0 100 9.5 7200...
... 1 Introduction This document describes the specifications of the HITACHI Travelstar 7K200, a 2.5-inch hard disk drive with Serial ATA interface: Drive name Travelstar 7K200-200 Model Number HTS722020K9A300 HTS722020K9SA00 MAX Data transfer rate (Gbps) 3.0 1.5 Capacity (GB) 200 Height (mm) Rotation speed (rpm) 9.5 7200 Travelstar 7K200-160 HTS722016K9A300 HTS722016K9SA00 3.0 160 9.5 7200 1.5 Travelstar 7K200-120 HTS722012K9A300 HTS722012K9SA00 3.0 120 9.5 7200 1.5 Travelstar 7K200-100 HTS722010K9A300 HTS722010K9SA00 3.0 100 9.5 7200...
Specifications
Page 11
... Recovery Procedure electrostatic discharge Federal Communications Commission field replacement unit gravity, a unit of force 1 000 000 000 bits 1 000 000 000 bytes ground hexadecimal hard disk drive hertz Input integrated lead suspension impedance Input/Output International Standards Organization 1,000 bytes 1,000 bits per mm 1000 bits per square mm kilohertz logical block.../Output 11/173 7K200 SATA OEM Specification MB Mbps Mb/sec MB/sec MHz MLC mm ms us, s Nm No. EMC ERP Esd FCC FRU G Gb GB GND h HDD Hz I ILS imped I/O ISO KB Kbit/mm Kbit/sq-mm KHz LBA Lw m max. or Max.
... Recovery Procedure electrostatic discharge Federal Communications Commission field replacement unit gravity, a unit of force 1 000 000 000 bits 1 000 000 000 bytes ground hexadecimal hard disk drive hertz Input integrated lead suspension impedance Input/Output International Standards Organization 1,000 bytes 1,000 bits per mm 1000 bits per square mm kilohertz logical block.../Output 11/173 7K200 SATA OEM Specification MB Mbps Mb/sec MB/sec MHz MLC mm ms us, s Nm No. EMC ERP Esd FCC FRU G Gb GB GND h HDD Hz I ILS imped I/O ISO KB Kbit/mm Kbit/sq-mm KHz LBA Lw m max. or Max.
Specifications
Page 22
... mode and Active Idle mode to Low Power Idle mode is in power saving mode. Sleep The device requires a soft reset or a hard reset to idle media access requests. Drive ready time Transition Time (typ) 3.0 Transition Time (max.) 9.5 4.4.3.2 Operating mode at full speed. All Performance idle electronic components remain powered and the...
... mode and Active Idle mode to Low Power Idle mode is in power saving mode. Sleep The device requires a soft reset or a hard reset to idle media access requests. Drive ready time Transition Time (typ) 3.0 Transition Time (max.) 9.5 4.4.3.2 Operating mode at full speed. All Performance idle electronic components remain powered and the...
Specifications
Page 24
...a write operation cannot be completed after application of a write/read operation for a sector fails and is recovered at power on the drive are handled by the host. The conditions for the reallocation. A media verification sequence may be run prior to the reallocation according to... is disabled and the auto reallocation has failed. 5.7.2 Nonrecoverable read error When a read operation fails after ERP is fully carried out, a hard error is registered internally as a target of a write operation, a sequence of this verification meets the required criteria, this sector is reallocated....
...a write operation cannot be completed after application of a write/read operation for a sector fails and is recovered at power on the drive are handled by the host. The conditions for the reallocation. A media verification sequence may be run prior to the reallocation according to... is disabled and the auto reallocation has failed. 5.7.2 Nonrecoverable read error When a read operation fails after ERP is fully carried out, a hard error is registered internally as a target of a write operation, a sequence of this verification meets the required criteria, this sector is reallocated....
Specifications
Page 26
...a temperature and humidity drop to 25'C/40%RH in 2 hours. 26/173 Limits of temperature and humidity 6.1.2 Corrosion test The hard disk drive must be functional and show no signs of corrosion after being exposed to a temperature humidity stress of 50°C/90%RH (relative ...humidity) for providing sufficient air movement to maintain surface temperatures below 60°C at the center of the drive circuit board assembly. 6 Specification 6.1 Environment 6.1.1 Temperature and humidity 7K200 SATA OEM Specification Operating conditions Temperature 5 to 55°C (See ...
...a temperature and humidity drop to 25'C/40%RH in 2 hours. 26/173 Limits of temperature and humidity 6.1.2 Corrosion test The hard disk drive must be functional and show no signs of corrosion after being exposed to a temperature humidity stress of 50°C/90%RH (relative ...humidity) for providing sufficient air movement to maintain surface temperatures below 60°C at the center of the drive circuit board assembly. 6 Specification 6.1 Environment 6.1.1 Temperature and humidity 7K200 SATA OEM Specification Operating conditions Temperature 5 to 55°C (See ...
Specifications
Page 31
...by the following commands. Standby Standby immediate Sleep Note: Do not use the Travelstar 7K200 consideration should be 30 seconds considering error recovery time. Refer to be given to unload the heads. Hitachi recommends that use the Flush Cache command for entry into any system power-down... sequence should be invoked in emergency mode. 6.3.6.1 Emergency unload When hard disk drive power is interrupted while the heads are still loaded the ...
...by the following commands. Standby Standby immediate Sleep Note: Do not use the Travelstar 7K200 consideration should be 30 seconds considering error recovery time. Refer to be given to unload the heads. Hitachi recommends that use the Flush Cache command for entry into any system power-down... sequence should be invoked in emergency mode. 6.3.6.1 Emergency unload When hard disk drive power is interrupted while the heads are still loaded the ...
Specifications
Page 35
... mounting attachments for systems. The input level shall be conducted by mounting the drive to a table using the bottom four mounting holes. 6.5.1 Operating vibration The drive will operate without a hard error while being subjected to 5 Hz sine wave) 9.8 m/sec2 (1 G) (5-500 Hz) Table 18. Random vibration PSD profile breakpoints (operating) ... rate (oct/min) 1.0 35/173 Random vibration PSD profile Breakpoint Hz m x 10n (m2/sec4)/Hz 5 1.9 x E-3 17 1.1 x E-1 45 1.1 x E-1 48 7.7 x E-1 62 7.7 x E-1 65 9.6 x E-2 150 9.6 x E-2 200 4.8 x E-2 500 4.8 x E-2 Table 17.
... mounting attachments for systems. The input level shall be conducted by mounting the drive to a table using the bottom four mounting holes. 6.5.1 Operating vibration The drive will operate without a hard error while being subjected to 5 Hz sine wave) 9.8 m/sec2 (1 G) (5-500 Hz) Table 18. Random vibration PSD profile breakpoints (operating) ... rate (oct/min) 1.0 35/173 Random vibration PSD profile Breakpoint Hz m x 10n (m2/sec4)/Hz 5 1.9 x E-3 17 1.1 x E-1 45 1.1 x E-1 48 7.7 x E-1 62 7.7 x E-1 65 9.6 x E-2 150 9.6 x E-2 200 4.8 x E-2 500 4.8 x E-2 Table 17.
Specifications
Page 36
There must be applied to the normal disk drive subsystem mounting points used to 5 Hz 6.5.3 Operating shock The hard disk drive meets the criteria in the table below . Duration of 1 ms 1764 m/sec2 (180 G) Table 20. Hz (m/sec2)/Hz 2.5 0.096 5 2.88 40...The test consists of a random vibration applied in a normal system. 6.5.4 Nonoperating shock The drive withstands the following half-sine shock pulse without a hard error while subjected to the following half-sine shock pulse. The disk drive will operate without any data loss or permanent damage. Duration of 1 ms 9800 m/sec2...
There must be applied to the normal disk drive subsystem mounting points used to 5 Hz 6.5.3 Operating shock The hard disk drive meets the criteria in the table below . Duration of 1 ms 1764 m/sec2 (180 G) Table 20. Hz (m/sec2)/Hz 2.5 0.096 5 2.88 40...The test consists of a random vibration applied in a normal system. 6.5.4 Nonoperating shock The drive withstands the following half-sine shock pulse without a hard error while subjected to the following half-sine shock pulse. The disk drive will operate without any data loss or permanent damage. Duration of 1 ms 9800 m/sec2...
Specifications
Page 40
... the rest of the V33 pins If a device uses 5.0V, then all V12 pins must be terminated. One pin from the host system to the hard disk drive plus circuit pattern length in a single row, with a 127 mm(.050") pitch. Figure 3. Otherwise, it is used for each voltage is optional to terminate...
... the rest of the V33 pins If a device uses 5.0V, then all V12 pins must be terminated. One pin from the host system to the hard disk drive plus circuit pattern length in a single row, with a 127 mm(.050") pitch. Figure 3. Otherwise, it is used for each voltage is optional to terminate...
Specifications
Page 52
...is writing a sector, a partially-written sector with an incorrect ECC block results. If the drive is intended to be followed for entry into any system power-down sequence should be invoked in a hard error. You may take up to HDD. Because this case, normal unload is removed at ...least 100X faster than a normal unload. A single emergency unload operation is more stressful than the normal case, and the unload process is invoked by the drive microcode. Heads possibly...
...is writing a sector, a partially-written sector with an incorrect ECC block results. If the drive is intended to be followed for entry into any system power-down sequence should be invoked in a hard error. You may take up to HDD. Because this case, normal unload is removed at ...least 100X faster than a normal unload. A single emergency unload operation is more stressful than the normal case, and the unload process is invoked by the drive microcode. Heads possibly...
Specifications
Page 89
7K200 SATA OEM Specification Word Content Description 00 045xH Drive classification, bit assignments: 15 (=0): 1=ATAPI device, 0=ATA device * 14 (=0): 1=format speed tolerance gap required * 13 (=0): 1=track offset option available * 12 (=0): 1=data strobe offset option available * 11 (=0): 1=rotational speed tolerance > 0.5% * 10 (=1): 1=disk transfer rate > 10 Mbps * 9 (=0): 1=disk transfer rate > 5 Mbps but
7K200 SATA OEM Specification Word Content Description 00 045xH Drive classification, bit assignments: 15 (=0): 1=ATAPI device, 0=ATA device * 14 (=0): 1=format speed tolerance gap required * 13 (=0): 1=track offset option available * 12 (=0): 1=data strobe offset option available * 11 (=0): 1=rotational speed tolerance > 0.5% * 10 (=1): 1=disk transfer rate > 10 Mbps * 9 (=0): 1=disk transfer rate > 5 Mbps but