Hitachi HTS542516K9SA00 Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi HTS542516K9SA00 manuals!
Problems with Hitachi HTS542516K9SA00?
Ask a Question
Free Hitachi HTS542516K9SA00 manuals!
Problems with Hitachi HTS542516K9SA00?
Ask a Question
Most Recent Hitachi HTS542516K9SA00 Questions
Windows Startup Failure
Hi, my Toshiba Satillite laptop does not load up to the user account area, before it does get to the...
Hi, my Toshiba Satillite laptop does not load up to the user account area, before it does get to the...
(Posted by zeshaanashraf 9 years ago)
Hitachi HTS542516K9SA00 Videos
Hitachi repair board swap 0A54296 HTS542512K9SA00 HTS542516K9SA00 HTS542580K9SA00
Duration: 4:26
Total Views: 31
Duration: 4:26
Total Views: 31
Popular Hitachi HTS542516K9SA00 Manual Pages
Specifications - Page 49
... command are shown in the following table. Code 01h 02h 03h 04h 05h Table 31 Diagnostic Codes
No error Detected Formatter device error Sector buffer error Ecc circuitry error Controller microprocessor error
Description
12.2 Diagnostic and Reset considerations
The Set Max password, the Set Max security mode and the Set Max unlock counter don't retain over a Power On Reset but persist...
Specifications - Page 55
... Password
('F6'h)
12.9.1 Security mode
Following security modes are set this feature as below. The device enables all commands. If a password is not set at the device ...hard disk device even if the device is
Page 55 of a degrading or fault condition existing. 5K250 (SATA) OEM Specification the device are less than or equal to their corresponding attribute thresholds, then the device...
Specifications - Page 57
Page 57 of 171 5K250 (SATA) OEM Specification
Figure 5 Initial Setting
12.9.1.2 Operation from POR after User Password is set
When Device Lock Function is enabled, the device rejects media access command until a Security Unlock command is successfully completed.
Specifications - Page 67
... / Write FPDMA Queued commands) is supported. The following Action codes are used to the section 8 SCT Command Transport in this feature sets. Setting Initialize device parameters
Power Management Feature Set Standby Timer Security mode state Set max address Set feature
Set multiple mode Table 38 Preserved Software Setting
5K250 (SATA) OEM Specification
Contents Track length Number of head...
Specifications - Page 72
... Sector(s) 3 Read Verify Sector(s) 3 Read Verify Sector(s) Ext 3 Recalibrate 2 Security Disable Password 3 Security Erase Prepare 2 Security Erase Unit 3 Security Freeze Lock 2 Security Set Password 2 Security Unlock 3 Seek 3 Sense Condition 3 Set Features Table 40 Command set
Protocol
Command Page 72 of 171
5K250 (SATA) OEM Specification
Code (Hex)
E5 98 B1 B1 B1 B1 90 E7 EA 50 F7...
Specifications - Page 78
... is returned to disable that feature, device abort that command and return error reason code as below .
ERROR INFORMATION EXAMPLE 1: After establish a protected area with DEVICE CONFIGURATION SET command, the device shall return command aborted.
5K250 (SATA) OEM Specification
14.2.3 DEVICE CONFIGURATION IDENTIFY (subcommand C2h)
The DEVICE CONFIGURATION IDENTIFY command returns a 512...
Specifications - Page 79
.... The sum of all byte in DMA Setup FIS supported
0 1 = Native command queuing supported
9-254
Reserved
255
Integrity word
15-8
Checksum
7-0
Signature (A5h)
Table 46 Device Configuration Overlay Data structure
Note.
5K250 (SATA) OEM Specification
Word
Content
0
0002h
Data Structure revision
1
Multiword DMA modes supported
15-3 Reserved
2 1 = Multiword DMA mode 2 and below...
Specifications - Page 88
... Setting is Valid
7- 0 xxh = Current setting for HTS5425XXK9SA00 / HTS5425XXK9A300" on Page 96
Table 55 Identify device information ---
Page 88 of cylinders/heads/sectors by models for...SATA) OEM Specification
Word
Content
Description
48
4000H
Trusted Computing feature set options
15(=0) Always 0
14(=1) Always 1
13- 1(=0) Reserved
0(=0) 1=Trusted Computing feature set is supported...
Specifications - Page 90
...Table 57 Identify device information --- 5K250 (SATA) OEM Specification
Word
Content
Description
78
005EH
SATA supported features
15-7(=0) Reserved
6(=1) 1=Software setting preservation supported
5(=0) Reserved
4(=1) 1=In-order data delivery supported
3(=1)
1=Device initiated interface power management supported
2(=1) 1=DMA Setup Auto-Activate optimization supported
1(=1)
1=Non-zero...
Specifications - Page 91
...
5K250 (SATA) OEM Specification
Word
Content
Description
83
7F69H
Command set supported
15 (=0) Always
14 (=1) Always
13 (=1) 1=FLUSH CACHE EXT command supported
12 (=1) 1=FLUSH CACHE command supported
11 (=1) 1=Device Configuration Overlay command supported
10 (=1) 1=48-bit Address feature set supported
9 (=1) 1=Automatic Acoustic Management supported
8 (=1) 1=SET MAX security...
Specifications - Page 94
...
Streaming Performance Granularity
100-103
Note.2
Maximum user LBA address for 48-bit Address feature set
Note.1 The '*' mark in 'Content' field indicates the use of 171 Page 94 of those parameters that are vendor specific. 5K250 (SATA) OEM Specification
Word
Content
Description
89
xxxxH
Time required for security erase unit completion
Time= value...
Specifications - Page 126
... Code
19-255
(valid if Word 0 bit 0 = 1) Reserved
Table 99 Security Set Password Information
Identifier
Zero indicates that the device should check the supplied password against the master password stored internally. 5K250 (SATA) OEM Specification
14.30 Security Set Password (F1h)
Command Block Output Registers
Register
76543210
Data
-------- LBA Low
-------- Device
-------- Error...
Specifications - Page 132
...DMA setup FIS DMA setup FIS auto-activate optimization Device-initiated interface power state transitions Guaranteed in 5 seconds after write command completion when write cache is 03h (=Set ...Saving mode is set to 10h or 90h, the value set to the Sector Count register specifies the specific Serial ATA feature to the Identify Device Information(129word) by Identify Device command. The ...
Specifications - Page 133
... The Device Feature
Destination code for that LBA/CYL are ignored. This command implement SET Max security extension commands as a default value. But regardless of 171 This command sets this command 01h SET MAX SET PASSWORD
Page 133 of Feature register value, the case this command is immediately preceded by a Read Native Max Address command, it is supported...
Specifications - Page 147
... describes the S.M.A.R.T. Bit
Definition
0
Pre-power mode attribute saving capability
If bit = 1, the device will save its Attribute Values prior to going into a power saving mode and supports the S.M.A.R.T.
ENABLE/DISABLE ATTRIBUTE AUTOSAVE command. 15
14.39.2.5
5K250 (SATA) OEM Specification The self-test routine in progress
Total Time in this field.
14.39...
Hitachi HTS542516K9SA00 Reviews
We have not received any reviews for Hitachi yet.