Instruction Manual
Page 5
...saw for example- Keep all other body parts near the drill bit or chuck during operation. Keep all guards or safety features ...per minute 5 Hold tools by a Hitachi authorized service center. 15. NEVER place hands or other ... bolts and covers tightly in the Instruction Manual. 10. NEVER use power tools if the plastic housing...the job of conditions below you do this tool V volts --n--o direct current no load speed ---/min ...... To reduce..., bolts, and plates tightly mounted. Because the cordless driver drill operates by children, individuals unfamiliar with soapy water and ...
...saw for example- Keep all other body parts near the drill bit or chuck during operation. Keep all guards or safety features ...per minute 5 Hold tools by a Hitachi authorized service center. 15. NEVER place hands or other ... bolts and covers tightly in the Instruction Manual. 10. NEVER use power tools if the plastic housing...the job of conditions below you do this tool V volts --n--o direct current no load speed ---/min ...... To reduce..., bolts, and plates tightly mounted. Because the cordless driver drill operates by children, individuals unfamiliar with soapy water and ...
Instruction Manual
Page 10
... temperature and power source voltage. 10 BCL1015 Lithium - ion battery DC 10.8 V About 1,000 times 1.8 lbs. (0.8 kg) 2. Battery Charger (UC10SFL) Caution plate Battery installation hole Body Pilot lamp Fig. 2 Nameplate SPECIFICATIONS 1. Cordless Driver Drill (DB10DL) Motor No-load speed Capacity Drilling Screw Wood (Thickness 11/16" (18 mm)) Wood screw Driver Small screw Bit shank size Model Battery Type Voltage...
... temperature and power source voltage. 10 BCL1015 Lithium - ion battery DC 10.8 V About 1,000 times 1.8 lbs. (0.8 kg) 2. Battery Charger (UC10SFL) Caution plate Battery installation hole Body Pilot lamp Fig. 2 Nameplate SPECIFICATIONS 1. Cordless Driver Drill (DB10DL) Motor No-load speed Capacity Drilling Screw Wood (Thickness 11/16" (18 mm)) Wood screw Driver Small screw Bit shank size Model Battery Type Voltage...
Instruction Manual
Page 13
...9, ... 21" on the clutch dial, or the black dot, with the numbers "1, 5, 9 ... 21" on the type of installing bit. 3. Line Fig. 7 6. While operating the driver drill, take care not to lock the motor. ● If the motor is set. Confirm that the battery is strongest at the line between.... (1) Tightening torque Tightening torque should correspond in its original position, then the bit is used as a drill, line up the clutch dial drill mark " " with the clutch dial set between the number "21" and the drill mark " ". Adjust the clutch dial in place, and the tool can be...
...9, ... 21" on the clutch dial, or the black dot, with the numbers "1, 5, 9 ... 21" on the type of installing bit. 3. Line Fig. 7 6. While operating the driver drill, take care not to lock the motor. ● If the motor is set. Confirm that the battery is strongest at the line between.... (1) Tightening torque Tightening torque should correspond in its original position, then the bit is used as a drill, line up the clutch dial drill mark " " with the clutch dial set between the number "21" and the drill mark " ". Adjust the clutch dial in place, and the tool can be...
Instruction Manual
Page 14
... Light Trigger switch Fig. 9 THE SCOPE AND SUGGESTIONS FOR USES Table 6 Work Clutch dial position Suggestions Drilling Wood Use for immediate stopping. 8. Use after releasing the trigger switch. (Fig. 9) 10. This is being pulled. The light keeps on lighting while the trigger switch is only a noise, ...; The rotational speed of the battery, etc. Use the bit and socket matching the screw diameter. When the trigger is pulled more . If this happens, charge the battery. (Fig. 10) Battery level warning lamp Fig. 10 NOTE: ⅜ The level at which the battery level warning...
... Light Trigger switch Fig. 9 THE SCOPE AND SUGGESTIONS FOR USES Table 6 Work Clutch dial position Suggestions Drilling Wood Use for immediate stopping. 8. Use after releasing the trigger switch. (Fig. 9) 10. This is being pulled. The light keeps on lighting while the trigger switch is only a noise, ...; The rotational speed of the battery, etc. Use the bit and socket matching the screw diameter. When the trigger is pulled more . If this happens, charge the battery. (Fig. 10) Battery level warning lamp Fig. 10 NOTE: ⅜ The level at which the battery level warning...
Instruction Manual
Page 15
...the exhausted battery WARNING: Do not dispose of children. 15 At the end of the bit The bits should be changed without prior notice. 5. To assure that you use a driver bit of which point is incinerated. Accordingly, some parts may damage the plastics. 4. So replace...use . CAUTION: If you have purchased contains a rechargeable battery. The battery must be carried out by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. 7. English CAUTION: ● While operating the Cordless driver drill, take care not to incorporate the latest technological advancements.
...the exhausted battery WARNING: Do not dispose of children. 15 At the end of the bit The bits should be changed without prior notice. 5. To assure that you use a driver bit of which point is incinerated. Accordingly, some parts may damage the plastics. 4. So replace...use . CAUTION: If you have purchased contains a rechargeable battery. The battery must be carried out by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. 7. English CAUTION: ● While operating the Cordless driver drill, take care not to incorporate the latest technological advancements.
Parts List
Page 3
CODE NO. DESCRIPTION 501 992-671 + DRIVER BIT (B) NO.2 50L 502 CHARGER (MODEL UC 10SFL) 503 329-585 CASE 504 BIT SET NO. STANDARD ACCESSORIES ITEM NO. USED 1 REMARKS 1 1 INCLUD. 604, 605 1 1 2 - 08 *ALTERNATIVE PARTS - 3 - CODE NO. USED 1 REMARKS 1 1 1 FOR USA, CAN DB 10DL OPTIONAL ACCESSORIES ITEM NO. DESCRIPTION 601 992-670 + DRIVER BIT (B) NO.1 50L 602 992-672 + DRIVER BIT (B) NO.3 50L 603 321-823 DRILL CHUCK AND ADAPTER SET 604 307-543 CHUCK ADAPTER 605 987-575 CHUCK WRENCH FOR 10VLB-D, 10VLR-D NO.
CODE NO. DESCRIPTION 501 992-671 + DRIVER BIT (B) NO.2 50L 502 CHARGER (MODEL UC 10SFL) 503 329-585 CASE 504 BIT SET NO. STANDARD ACCESSORIES ITEM NO. USED 1 REMARKS 1 1 INCLUD. 604, 605 1 1 2 - 08 *ALTERNATIVE PARTS - 3 - CODE NO. USED 1 REMARKS 1 1 1 FOR USA, CAN DB 10DL OPTIONAL ACCESSORIES ITEM NO. DESCRIPTION 601 992-670 + DRIVER BIT (B) NO.1 50L 602 992-672 + DRIVER BIT (B) NO.3 50L 603 321-823 DRILL CHUCK AND ADAPTER SET 604 307-543 CHUCK ADAPTER 605 987-575 CHUCK WRENCH FOR 10VLB-D, 10VLR-D NO.
