Hitachi CJ18DL - HXP Lithium-Ion Cordless Jig Saw Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi CJ18DL manuals!
Problems with Hitachi CJ18DL?
Ask a Question
Free Hitachi CJ18DL manuals!
Problems with Hitachi CJ18DL?
Ask a Question
Popular Hitachi CJ18DL Manual Pages
Instruction Manual - Page 3
... understand all of electric shock. Most accidents that has not been specifically recommended by the failure to lose control. refrigerators.
risk of the safety precautions, warnings and operating instructions in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in this power tool in the presence of fumes. the risk of a cord suitable...
Instruction Manual - Page 4
...only with the power tool or these instructions
Carrying power tools with specifically
dust extraction ...replacement parts.
f) Keep cutting tools sharp and clean. working conditions and the work to a rotating
from one type of fire when
caught in moving parts,
breakage of power tool, taking into power tools
in power tools that cannot be repaired. injury.
5) Battery tool...
Instruction Manual - Page 5
... or unauthorized personnel. 9. Do not wipe plastic parts with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
2. SPECIFIC SAFETY RULES AND SYMBOLS
1. Keep motor air vent clean. Don't leave tool until repaired. 11. Check for repairs by a Hitachi authorized service center.
14. NEVER use power tools if the plastic housing or handle is...
Instruction Manual - Page 6
... volts
qualified serviceman when service or repair is properly wired and in any
maintenance or cleaning.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER
7. An extension cord should not be used make sure:
these risks, follow these active wiring or electric cable with buried object such as those of injury, charge HITACHI
electric cable within the...
Instruction Manual - Page 7
... not the trouble but the result of the battery or battery charger can lead to read all instructions and cautionary ...damage the charger. 13. Before using the model UC18YRL or UC18YFL battery charger, be sure...power tool during work , the battery power may stop . NEVER store the battery or battery charger in use only where there is overloaded, the motor may stop . In this manual...
Instruction Manual - Page 9
... read and understood all safety instructions contained in this Instruction Manual may show details or attachments that differ from those on the tool unless you in this manual. NEVER operate, or attempt any maintenance on your own power tool. Cordless Jig Saw (CJ14DL / CJ18DL)
Lock off button
Switch
Lever LED light
Blade
Battery
Base Change knob Guide roller
⅜ Battery Terminal hole...
Instruction Manual - Page 10
...red) Battery installation hole
Fig. 2
Nameplate
SPECIFICATIONS
Model Motor No-Load Speed Capacity
Stroke
Min. Battery Charger
Model Input power source Charging ...power source voltage.
10 ion battery
DC 14.4V
DC 18V
3 Ah
1.5 Ah
5.1 lbs (2.3 kg)
5.3 lbs (2.4 kg) 4.8 lbs (2.2 kg)
2. English 2. cutting radius
Model
Battery
Type Voltage
Capacity
Weight
CJ14DL
CJ18DL
DC motor...
Instruction Manual - Page 12
...of the receptacle by pulling on the cord. Supporting the battery charger with hand, pull out ...inserted in direct sunlight. If the problem persists, call for repairs. ● Leave 5 minutes between...the charge time lamp does not light when the power cord is connected to avoid damaging cord.
5. Table... seconds. (off for rechargeable batteries are only a guide, and
may lead to fire.
● If ...
Instruction Manual - Page 14
...Set the change knob shown in Fig. 11 to "0" to the trigger.
Cutting stainless steel plates This Jig Saw can cut stainless steel plates by the pressure you apply to eliminate the orbital operation (the blade moves only up and down ). The blade..., etc., increase the
9.
The tool can be adjusted from flying off button (Fig. 9)
The jig saw is equipped with a variable speed ...
Instruction Manual - Page 15
..., if the tool is not the trouble but the result of protection function. However, this case, release the switch of tool and eliminate the causes of overloading. Using the guide (sold separately)...motor may stop the output.
NOTE: To ensure accurate cutting when using the Guide (Fig. 17), always set the orbital position to stop .
Attach the sub base to the work piece while sawing...
Instruction Manual - Page 16
... gear cover. (Fig. 21)
(3) Tighten the M5 bolt again. (Fig. 15) (4) Set the orbital position to start cutting.
16
Base
Fig. 20 -mark
Semicircular part
Fig. 21
Scale
Guide
Nail or screw Guide hole
Fig. 18
4. Pocket cutting (1) In lumber Aligning the blade direction with the [ ] mark on base and move the base fully forward...
Instruction Manual - Page 19
... that only authorized replacement parts will
A: Item No. code numbers and/
for recycling options or proper disposal.
6. Inspecting the blade
8.
Disposal of the exhausted battery
WARNING: Do not dispose of the motor.
Service parts list
Continued use bleach, chlorine, gasoline or thinner,
MODIFICATIONS: Hitachi Power Tools are dangerous.
Replace the blade with oil or...
Instruction Manual - Page 64
... 15-1, Konan 2-chome, Minato-ku, Tokyo 108-6020, Japan
Distributed by
Hitachi Koki Co., Ltd.
LTD. número 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTORIZED POWER TOOL SERVICE CENTER.
Unit B, Mississauga ON L5T 2A4
801 Code No. at 1-800-59-TOOLS (toll free), or HITACHI AUTHORIZED POWER TOOL SERVICE CENTER recarding COLLECTION. Con respecto a la RECOLECCIÓN de baterí...
Parts List - Page 2
... 328-361 MOTOR DC 18V
1 INCLUD. 19
* 20 328-739 MOTOR DC 18V
1 INCLUD. 19 FOR USA, CAN
21 321-580 LEVER SPRING
1
22 328-347 LEVER
1
23 328-348 LEVER BOLT
1
24 325-241 SEAL LOCK HEX. BOLT M3X8 1
25 325-077 SEAL LOCK HEX.
SOCKET HD. CODE NO.
1 328-362
DESCRIPTION HOUSING (A).(B) SET
NO. USED...
Parts List - Page 4
... 879-340 JIG SAW BLADES NO. 21 (5 PCS.)
1
607 879-341 JIG SAW BLADES NO. 22 (5 PCS.)
1
608 321-878 JIG SAW BLADES (LONG) 185L (3 PCS.) 1
609 321-992 SUB BASE (A) SET (STEEL)
1 INCLUD. 610
610 321-996 SPECIAL BOLT
4
611 321-593 GUIDE
1
612 325-149 GREASE (MOLUB-ALLOY NO. 777-1) 75G 1
--- 4 ---
* ALTERNATIVE PARTS
Printed in Japan 7 -- 07 (070725N) CODE NO. USED...
Hitachi CJ18DL Reviews
We have not received any reviews for Hitachi yet.