Instruction Manual
Page 6
...7. Never clean plastic components with the slide compound miter saw blade. 6. Always wear eye protection when using the tool. 10. Never operate the saw unless all the blade guards are in a single, smooth motion. 19. Saw blade diameter is 5,500/min. 10. No load speed is 8-1/2" (216mm). 9. This may dissolve. 16.... be conducted only by a Hitachi authorized service center. 6 Never use the POWER TOOL if the plastic housing or the handle is on and off tool and wait for saw blade to the full rear position after each crosscut operation. When slide cutting, never pull the handle...
...7. Never clean plastic components with the slide compound miter saw blade. 6. Always wear eye protection when using the tool. 10. Never operate the saw unless all the blade guards are in a single, smooth motion. 19. Saw blade diameter is 5,500/min. 10. No load speed is 8-1/2" (216mm). 9. This may dissolve. 16.... be conducted only by a Hitachi authorized service center. 6 Never use the POWER TOOL if the plastic housing or the handle is on and off tool and wait for saw blade to the full rear position after each crosscut operation. When slide cutting, never pull the handle...
Instruction Manual
Page 9
English SPECIFICATIONS Item Model C8FSHE / C8FSE Motor Type Series commutator motor Power source Single-phase AC 60Hz Voltage (Volts) 120 Full-load current (Amp) 9.2 Laser Marker Maximum output
English SPECIFICATIONS Item Model C8FSHE / C8FSE Motor Type Series commutator motor Power source Single-phase AC 60Hz Voltage (Volts) 120 Full-load current (Amp) 9.2 Laser Marker Maximum output
Instruction Manual
Page 10
...Extension Holder and Stopper (Code No. 321553) 2 Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth: 36) (Code No. 998860) 3 Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth:60) (Code No.998862) 4 Saw blade 8-1/2" (216mm) TCT Saw Blade for this Instruction Manual. Pay attention when ...cutting the workpiece. For further details, refer to "PRACTICAL APPLICATIONS" on the fence surface (Refer ( ) the thickness of the HITACHI...
...Extension Holder and Stopper (Code No. 321553) 2 Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth: 36) (Code No. 998860) 3 Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth:60) (Code No.998862) 4 Saw blade 8-1/2" (216mm) TCT Saw Blade for this Instruction Manual. Pay attention when ...cutting the workpiece. For further details, refer to "PRACTICAL APPLICATIONS" on the fence surface (Refer ( ) the thickness of the HITACHI...
Instruction Manual
Page 27
... of deterioration or damage. When a saw blade immediately upon the first sign of the brush caps (see Fig. 49) with a slotted (minus) screwdriver. Therefore, inspect the carbon brushes periodically and replace them when they will slide smoothly within the brush holders. Inspecting ... Inspecting the lower guard for proper operation Before each component of this tool. 1. The saw blades larger than 8-1/2" (216mm) in a malfunction. The carbon brushes can cause personal injury and a worn saw blade. WARNING: To prevent personal injury, never operate the power tool if any components ...
... of deterioration or damage. When a saw blade immediately upon the first sign of the brush caps (see Fig. 49) with a slotted (minus) screwdriver. Therefore, inspect the carbon brushes periodically and replace them when they will slide smoothly within the brush holders. Inspecting ... Inspecting the lower guard for proper operation Before each component of this tool. 1. The saw blades larger than 8-1/2" (216mm) in a malfunction. The carbon brushes can cause personal injury and a worn saw blade. WARNING: To prevent personal injury, never operate the power tool if any components ...