Internal Cabling Guide for HP Smart Array Controllers
Page 12
...5302 or 5304 Controller Card with Dual Partition Cabling NOTE When cabling the HP Smart Array 5302 or 5304 controller card to the Server Expansion Unit (SEU), the PCI-X I/O and SCSI HDD Backplane architecture are identical between the rx8620 server and the Server Expansion Unit. Cabling... for the HP Integrity rx8620 Server Recabling for recabling the rx8620 server. Adding the Server Expansion Unit allows for...
...5302 or 5304 Controller Card with Dual Partition Cabling NOTE When cabling the HP Smart Array 5302 or 5304 controller card to the Server Expansion Unit (SEU), the PCI-X I/O and SCSI HDD Backplane architecture are identical between the rx8620 server and the Server Expansion Unit. Cabling... for the HP Integrity rx8620 Server Recabling for recabling the rx8620 server. Adding the Server Expansion Unit allows for...
Internal Cabling Guide for HP Smart Array Controllers
Page 27
... cover slightly away from the PCI backplane. Remove the corresponding PCI card. Carefully slide a long-shaft, medium-width, flat-headed screwdriver into the PCI backplane connector (Item 1 in PCI slot 4 for the HP Integrity rx5670 Server Installing the HP Smart Array 5302 or 5304 Controller Card... Installing the HP Smart Array 5302 or 5304 Controller Card Step 1. b. Press one on...
... cover slightly away from the PCI backplane. Remove the corresponding PCI card. Carefully slide a long-shaft, medium-width, flat-headed screwdriver into the PCI backplane connector (Item 1 in PCI slot 4 for the HP Integrity rx5670 Server Installing the HP Smart Array 5302 or 5304 Controller Card... Installing the HP Smart Array 5302 or 5304 Controller Card Step 1. b. Press one on...
Internal Cabling Guide for HP Smart Array Controllers
Page 37
...) B 2 A 1 0 Your server's internal hard disk drives can be set up for their controller and the hard disk drive backplane (described below . Cabling for the HP 9000 rp3440 Server Recabling for RAID Recabling for RAID If the HP Smart Array controller card is then routed and connected to physical drive 2 (see Figure 4-5 and Figure 4-6). •...
...) B 2 A 1 0 Your server's internal hard disk drives can be set up for their controller and the hard disk drive backplane (described below . Cabling for the HP 9000 rp3440 Server Recabling for RAID Recabling for RAID If the HP Smart Array controller card is then routed and connected to physical drive 2 (see Figure 4-5 and Figure 4-6). •...
Internal Cabling Guide for HP Smart Array Controllers
Page 39
...(see Figure 4-5), depending upon whether you want to use one or both channels of the HP Smart Array controller card: • Single channel: unplug backplane SCSI cable Channel A (bottom) connector • Dual channel: unplug backplane SCSI cable Channel A (bottom) and SCSI cable Channel B (top) connectors Step 5. ...of the SCSI cables connected to the hard drive backplane (see Figure 4-12). Disconnect the power cables and any LAN or telecommunications cables from the back of the server chassis). Cabling for the HP 9000 rp3440 Server Recabling for the 25-Pin Management Port located...
...(see Figure 4-5), depending upon whether you want to use one or both channels of the HP Smart Array controller card: • Single channel: unplug backplane SCSI cable Channel A (bottom) connector • Dual channel: unplug backplane SCSI cable Channel A (bottom) and SCSI cable Channel B (top) connectors Step 5. ...of the SCSI cables connected to the hard drive backplane (see Figure 4-12). Disconnect the power cables and any LAN or telecommunications cables from the back of the server chassis). Cabling for the HP 9000 rp3440 Server Recabling for the 25-Pin Management Port located...
Internal Cabling Guide for HP Smart Array Controllers
Page 40
... goes between PCI slots 3 and 4 and part of the following, depending on the PCI cage (see Figure 4-15). Cabling for the HP 9000 rp3440 Server Recabling for single or dual channel support: a. Disconnect and remove any unused SCSI cables from obstructing access to prevent it from System Board...cable into PORT A2 of the A7231-63024 single channel cable labeled "PORT 1" into the hard drive backplane yet. The 36 Chapter 4 Single Channel Support: Plug the end of the HP Smart Array controller card (see Figure 4-14). The cable connectors are marked for clarity. Figure 4-13...
... goes between PCI slots 3 and 4 and part of the following, depending on the PCI cage (see Figure 4-15). Cabling for the HP 9000 rp3440 Server Recabling for single or dual channel support: a. Disconnect and remove any unused SCSI cables from obstructing access to prevent it from System Board...cable into PORT A2 of the A7231-63024 single channel cable labeled "PORT 1" into the hard drive backplane yet. The 36 Chapter 4 Single Channel Support: Plug the end of the HP Smart Array controller card (see Figure 4-14). The cable connectors are marked for clarity. Figure 4-13...
Internal Cabling Guide for HP Smart Array Controllers
Page 41
... Figure 4-16). Figure 4-16 RAID Cable Routing Through the PCI Cage Board Cover Chapter 4 1 37 Cabling for the HP 9000 rp3440 Server Recabling for RAID other end of the cable into the hard drive backplane yet. You do this later. Replace the PCI cage board cover, routing the RAID cable out of the...
... Figure 4-16). Figure 4-16 RAID Cable Routing Through the PCI Cage Board Cover Chapter 4 1 37 Cabling for the HP 9000 rp3440 Server Recabling for RAID other end of the cable into the hard drive backplane yet. You do this later. Replace the PCI cage board cover, routing the RAID cable out of the...
Internal Cabling Guide for HP Smart Array Controllers
Page 42
... Cover Step 15. Connect the free end(s) of fan 3 to the hard drive backplane (see Item 1 in Figure 4-17) to the backplane. Lower the fan power bridge. Cabling for the HP 9000 rp3440 Server Configuring the Server Firmware and Software for an external RAID storage system 38 Chapter... 4 Note that help you manage your HP Smart Array controller card in an HP 9000 server (use HP Smart Array utilities) ...
... Cover Step 15. Connect the free end(s) of fan 3 to the hard drive backplane (see Item 1 in Figure 4-17) to the backplane. Lower the fan power bridge. Cabling for the HP 9000 rp3440 Server Configuring the Server Firmware and Software for an external RAID storage system 38 Chapter... 4 Note that help you manage your HP Smart Array controller card in an HP 9000 server (use HP Smart Array utilities) ...
Internal Cabling Guide for HP Smart Array Controllers
Page 47
... server from the bulkhead end of the hard drive backplane, and is then routed and connected to physical drive 2 (see Figure 5-6). Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for RAID If the HP Smart Array controller card is required when connecting the HP Smart Array controller card to the internal hard...
... server from the bulkhead end of the hard drive backplane, and is then routed and connected to physical drive 2 (see Figure 5-6). Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for RAID If the HP Smart Array controller card is required when connecting the HP Smart Array controller card to the internal hard...
Internal Cabling Guide for HP Smart Array Controllers
Page 48
... RAID support. Step 1. To use RAID with your server's internal hard disk drives, you must connect the HP Smart Array controller card to the hard drive backplane and the internal SCSI cables, you must disconnect the internal SCSI cable(s) from the system. Cabling for the... HP Integrity rx2620 and rx2600 Servers Recabling for RAID Figure 5-7 Default Cabling for Internal Hard Drives B A Figure 5-8 Physical Drive Location ...
... RAID support. Step 1. To use RAID with your server's internal hard disk drives, you must connect the HP Smart Array controller card to the hard drive backplane and the internal SCSI cables, you must disconnect the internal SCSI cable(s) from the system. Cabling for the... HP Integrity rx2620 and rx2600 Servers Recabling for RAID Figure 5-7 Default Cabling for Internal Hard Drives B A Figure 5-8 Physical Drive Location ...
Internal Cabling Guide for HP Smart Array Controllers
Page 49
... power cables and any LAN or telecommunications cables from the back of the HP Smart Array controller card: • Single channel: unplug backplane SCSI cable Channel A (bottom) connector • Dual channel: unplug backplane SCSI cable Channel A (bottom) and SCSI cable Channel B (top) ...connectors Step 5. Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for grasping ...
... power cables and any LAN or telecommunications cables from the back of the HP Smart Array controller card: • Single channel: unplug backplane SCSI cable Channel A (bottom) connector • Dual channel: unplug backplane SCSI cable Channel A (bottom) and SCSI cable Channel B (top) ...connectors Step 5. Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for grasping ...
Internal Cabling Guide for HP Smart Array Controllers
Page 51
...cable connectors are marked for clarity. NOTE Do not reinstall the PCI cage or plug the other part of the cable into the hard drive backplane yet. The cable connectors are marked for clarity. Dual Channel Support: For 5300 series cards, plug the ends of the A7231-63025 dual ...A7231-63024 dual channel cable labeled "PORT 1" and "PORT 2" into PORT 1 of the cable into the hard drive backplane yet. You do this later. Chapter 5 47 The other end of the HP Smart Array controller card. Be sure it lies flush against where the PCI board cover and cable channel fit...
...cable connectors are marked for clarity. NOTE Do not reinstall the PCI cage or plug the other part of the cable into the hard drive backplane yet. The cable connectors are marked for clarity. Dual Channel Support: For 5300 series cards, plug the ends of the A7231-63025 dual ...A7231-63024 dual channel cable labeled "PORT 1" and "PORT 2" into PORT 1 of the cable into the hard drive backplane yet. You do this later. Chapter 5 47 The other end of the HP Smart Array controller card. Be sure it lies flush against where the PCI board cover and cable channel fit...
Internal Cabling Guide for HP Smart Array Controllers
Page 52
... Cover 1 Step 14. They must be flush against the controller card, with the latter half of the cable bent in order to the hard drive backplane (see Item 1 in Figure 5-18). Note that the cable should be routed around the chassis side of the cover's cable channel (see Item 1 in ...Figure 5-19). Place the PCI cage back into the system. Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for RAID Figure 5-16 Single Channel RAID Cabling from a Controller Card Installed in the PCI Cage Figure 5-17 Dual...
... Cover 1 Step 14. They must be flush against the controller card, with the latter half of the cable bent in order to the hard drive backplane (see Item 1 in Figure 5-18). Note that the cable should be routed around the chassis side of the cover's cable channel (see Item 1 in ...Figure 5-19). Place the PCI cage back into the system. Cabling for the HP Integrity rx2620 and rx2600 Servers Recabling for RAID Figure 5-16 Single Channel RAID Cabling from a Controller Card Installed in the PCI Cage Figure 5-17 Dual...
Internal Cabling Guide for HP Smart Array Controllers
Page 53
Connect the free end(s) of the RAID cable(s) from the EFI shell) • Install and use HP Smart Array utilities and command line options from the controller card to the backplane. Lower the fan power bridge. Step 20. The cable connectors are marked. Step 17. Step 18. Configuring the Server Firmware and Software...
Connect the free end(s) of the RAID cable(s) from the EFI shell) • Install and use HP Smart Array utilities and command line options from the controller card to the backplane. Lower the fan power bridge. Step 20. The cable connectors are marked. Step 17. Step 18. Configuring the Server Firmware and Software...
Internal Cabling Guide for HP Smart Array Controllers
Page 58
... card. See Figure 6-4. See Figure 6-5. 54 Chapter 6 Step 9. See Figure 6-3. Continue routing the cable parallel to the connector on the SCSI backplane. Step 12. Install the PCI cage into the server chassis. Step 10. Attach the SCSI Channel A connector (previously removed from PCI slot 2.... PCI slot 2 connector. Figure 6-4 Cable Routing Under Power Supply Bracket Power Supply Bracket Step 14. Cabling for the HP Integrity rx1620 Server Installing the HP Smart Array 6402 Controller Card Figure 6-3 Cable Routing on Smart Array Card and PCI Cage Exit parallel to the A1...
... card. See Figure 6-4. See Figure 6-5. 54 Chapter 6 Step 9. See Figure 6-3. Continue routing the cable parallel to the connector on the SCSI backplane. Step 12. Install the PCI cage into the server chassis. Step 10. Attach the SCSI Channel A connector (previously removed from PCI slot 2.... PCI slot 2 connector. Figure 6-4 Cable Routing Under Power Supply Bracket Power Supply Bracket Step 14. Cabling for the HP Integrity rx1620 Server Installing the HP Smart Array 6402 Controller Card Figure 6-3 Cable Routing on Smart Array Card and PCI Cage Exit parallel to the A1...
Installation Guide, Seventh Edition - HP 9000 rp3410 and HP 9000 rp3440
Page 53
... Observe all ESD safety precautions before attempting this warning can result in personal injury or damage to the server. Inserting a PCI card into the PCI backplane connector. Remove the cover. (See "Removing and Replacing the Top Cover on a Rack-Mounted Server" on page 26.) Chapter 1 53 See the labels on the...
... Observe all ESD safety precautions before attempting this warning can result in personal injury or damage to the server. Inserting a PCI card into the PCI backplane connector. Remove the cover. (See "Removing and Replacing the Top Cover on a Rack-Mounted Server" on page 26.) Chapter 1 53 See the labels on the...
Installation Guide, Seventh Edition - HP 9000 rp3410 and HP 9000 rp3440
Page 67
...8226; LVD/SE SCSI port. - External connections to the SCSI HBA core I/O controller are only supported when the internal cable between the SCSI backplane and the SCSI HBA core I /O SCSI HBA. The LAN board provides the basic external I/O connectivity for external mass storage devices. WARNING ...connected separately to the server. - AC Input Power The server comes with one or two power supplies installed. Core I/O Connections Each HP 9000 rp3410 and rp3440 server core I /O interface. - The server is shipped in the off and all power sources have been disconnected from the server...
...8226; LVD/SE SCSI port. - External connections to the SCSI HBA core I/O controller are only supported when the internal cable between the SCSI backplane and the SCSI HBA core I /O SCSI HBA. The LAN board provides the basic external I/O connectivity for external mass storage devices. WARNING ...connected separately to the server. - AC Input Power The server comes with one or two power supplies installed. Core I/O Connections Each HP 9000 rp3410 and rp3440 server core I /O interface. - The server is shipped in the off and all power sources have been disconnected from the server...
Installation Guide, Seventh Edition - HP 9000 rp3410 and HP 9000 rp3440
Page 87
... during installation are usually due to rough handling. The drive may not be caused by faulty interconnections. Remove and reinstall the hard drive backplane. Replace the hard drive backplane. If you are experiencing monitor, keyboard, or mouse problems, follow these steps: Chapter 1 87 Verify that the ac power source is random. 2. Replace...
... during installation are usually due to rough handling. The drive may not be caused by faulty interconnections. Remove and reinstall the hard drive backplane. Replace the hard drive backplane. If you are experiencing monitor, keyboard, or mouse problems, follow these steps: Chapter 1 87 Verify that the ac power source is random. 2. Replace...
User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440
Page 8
...Guide 148 Removing and Replacing System Memory 149 Supported DIMM Sizes...149 rp3410 Memory Configuration...150 Memory Loading Rules...151 rp3440 Memory Configuration...151 Memory Loading Rules...151 System Firmware Requirements...151 Replacing Deallocated Memory Ranks 151 Removing System Memory...152... a PCI or Graphics Card 169 Replacing a PCI or Graphics Card 170 Removing and Replacing the PCI Backplane 171 Removing the PCI Backplane...171 Replacing the PCI Backplane...171 Removing and Replacing a Removable Media Drive 172 Removing a Removable Media Drive 172 Replacing a Removable ...
...Guide 148 Removing and Replacing System Memory 149 Supported DIMM Sizes...149 rp3410 Memory Configuration...150 Memory Loading Rules...151 rp3440 Memory Configuration...151 Memory Loading Rules...151 System Firmware Requirements...151 Replacing Deallocated Memory Ranks 151 Removing System Memory...152... a PCI or Graphics Card 169 Replacing a PCI or Graphics Card 170 Removing and Replacing the PCI Backplane 171 Removing the PCI Backplane...171 Replacing the PCI Backplane...171 Removing and Replacing a Removable Media Drive 172 Removing a Removable Media Drive 172 Replacing a Removable ...
User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440
Page 9
Removing and Replacing the Hard Disk Drive (SCSI) Backplane 189 Removing the Hard Drive Disk SCSI Backplane 189 Replacing the Hard Disk Drive SCSI Backplane 191 A Replacement Parts...193 Parts Illustrations...193 Customer Self Repair...194 Replaceable Parts List...195 B Utilities...199 Boot Console Handler...199 BCH Commands...199 BCH ...
Removing and Replacing the Hard Disk Drive (SCSI) Backplane 189 Removing the Hard Drive Disk SCSI Backplane 189 Replacing the Hard Disk Drive SCSI Backplane 191 A Replacement Parts...193 Parts Illustrations...193 Customer Self Repair...194 Replaceable Parts List...195 B Utilities...199 Boot Console Handler...199 BCH Commands...199 BCH ...
User Service Guide, Sixth Edition - HP 9000 rp3410/rp3440
Page 12
... PCI Card Cage Cover 168 6-56 Installing a PCI Slot Cover...170 6-57 Installing a PCI Card...170 6-58 Removing the PCI Backplane...171 6-59 Replacing the PCI Backplane...172 6-60 Removing the Removable Media Drive 173 6-61 Removing the iLO MP card...174 6-62 Removing the iLO MP Card Battery ...176 6-63 Removing the LED Status Panel 177 6-64 Removing the Mechanical Covers 178 6-65 Removing the Backplane System Board Mounting Screws 178 6-66 Removing the System Board Mounting Screw 179 6-67 Removing the System Board...180 6-68 Aligning the System Board ...
... PCI Card Cage Cover 168 6-56 Installing a PCI Slot Cover...170 6-57 Installing a PCI Card...170 6-58 Removing the PCI Backplane...171 6-59 Replacing the PCI Backplane...172 6-60 Removing the Removable Media Drive 173 6-61 Removing the iLO MP card...174 6-62 Removing the iLO MP Card Battery ...176 6-63 Removing the LED Status Panel 177 6-64 Removing the Mechanical Covers 178 6-65 Removing the Backplane System Board Mounting Screws 178 6-66 Removing the System Board Mounting Screw 179 6-67 Removing the System Board...180 6-68 Aligning the System Board ...