HP Model 744rt - VME Workstation Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
This item is in your list!
View All Support Options Below
Free HP Model 744rt manuals!
Problems with HP Model 744rt?
Ask a Question
Free HP Model 744rt manuals!
Problems with HP Model 744rt?
Ask a Question
Popular HP Model 744rt Manual Pages
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 1
A4980-90601 Edition E0698
Printed in U.S.A. Installing the A4980A EISA-to-PCI Backplane Upgrade
This upgrade is to be performed only by HP qualified service personnel. HP Part No.
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 2
No part of the Rights in the United States ...Clause at DFARS 252.227.7013. Hewlett-Packard shall not be photocopied, reproduced or translated to restrictions as set forth in subdivision (c) (1) (ii) of this material. NOTICE The information contained in this document is... of this document may be liable for errors contained herein or for the use or reliability of Hewlett-Packard Company.
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 3
... a rack, remove it contains the following items: • PCI backplane • GSC-to-PCI interface board
Tools Required
You'll need the following items to install the PCI Module: • #1 Pozidriv screwdriver (with extension) • T10 and T-15 Torx screwdrivers • Static-free work area. To avoid electrical shock, make sure...
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 4
... electrostatic shock. Attach the static-grounding wrist strap by following precautions during the installation procedure.
• Stand on the package that any accumulated electrostatic charge discharges from your body to prevent damage from occurring, observe the following the instructions on a static-free mat
• Wear a static-grounding wrist strap to ensure that...
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 5
Installation
1 Remove the system top cover (see Figure 1). Installation
Screws
Screws
Figure 1
Removing the Top Cover
Screws 5
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 6
Installation 2 Remove the front bezel (see Figure 2). Figure 2
Removing the Front Bezel
6
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 7
Installation
3 Remove the two screws from the rear of the system, and slide the mid-tray toward the front, and then up, out of the system (see Figure 3). Figure 3
Removing the Mid-Tray
7
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 8
Figure 4
Removing the EISA Backplane Assembly
8 Installation
4 Remove any installed EISA cards. 5 Remove the EISA backplane/interface assembly (see Figure 4).
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 9
Figure 5
Assembling the PCI Backplane Components
9 Installation 6 Assemble the PCI backplane/interface assembly (see Figure 5).
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 10
Figure 6 NOTE:
Installing the PCI Backplane Assembly The PCI backplane only supports option cards with +5 volt bus signalling.
10 Installation 7 Install the PCI backplane assembly into the chassis (see Figure 6).
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 11
Installation
Figure 7
Installing a PCI Card
8 Replace the mid-tray into the system, and secure it with the two screws. 9 Replace the front bezel and the bezel screws. 10 Install PCI cards and secure them with the screws used for the EISA cards
(see Figure 7). 11 Replace the top cover and cover screws
11
Installing the A4980A EISA-to-PCI Backplane Upgrade - Page 12
... use the SAM utility to configure the HP-UX kernel for PCI support. 16 When SAM has started, choose the Kernel Configuration -> menu. 17 From the Kernel Configuration menu, choose Drivers 18 From the Drivers menu, select GSCtoPCI Driver. 19 Go to the Actions menu and select Add Driver to Kernel. 20 Now go to the...
HP Model 744rt Reviews
Do you have an experience with the HP Model 744rt that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!