HP A180 Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
HP A180 Videos
? 2013 Mercedes A180 CDI - DESIGN
Duration: 2:40
Total Views: 12,276
Duration: 2:40
Total Views: 12,276
? 2013 Mercedes A180 CDI - INTERIOR
Duration: 1:58
Total Views: 80,459
Duration: 1:58
Total Views: 80,459
2013 Mercedes A-Class (A180 CDI) - Driving
Duration: 2:15
Total Views: 120,686
Duration: 2:15
Total Views: 120,686
Popular HP A180 Manual Pages
HP DLPI Programmer's Guide - Page 11
... the updated or new editions, you should subscribe to correct errors or document product changes. Intended Audience
This manual is printed. The users are made at http://docs.hp.com.
The document printing date and part number indicate the document's current edition. Minor changes may be issued between editions to the appropriate product support service. The document part...
HP DLPI Programmer's Guide - Page 20
... throughout this guide. The Service Interface
Each layer of the OSI Reference Model has the following two standards: • One that defines the services provided by the layer. • One that architecture. The description of the model assumes familiarity with the OSI Reference Model. A model of the data link layer is responsible for the transmission and error-free...
HP DLPI Programmer's Guide - Page 38
... addresses on a per stream basis. The provider indicates success with a DL_OK_ACK message and failure with a DL_ERROR_ACK message. Introduction to DLPI DLPI Services
Figure 1-8
DL_ENABMULTI_REQ requests the DLS provider to disable specific multicast addresses on a per stream basis. The provider indicates success with a DL_OK_ACK message and failure with a DL_ERROR_ACK message.
38
Chapter...
HP DLPI Programmer's Guide - Page 124
... received before an acknowledgment is valid and the primitive was issued from a valid state, the DLS provider responds with a DL_OK_ACK.
DLPI Primitives Connection-mode Service Primitives
NOTE
Setting the ack thresh will not affect the local window size. Parameters
dl_primitive
DL_HP_SET_ACK_THRESH_REQ dl_ack_thresh
maximum number of I PDUs that can be greater than the...
HP DLPI Programmer's Guide - Page 131
... Failure DL_BADADDR
The destination DLSAP address was not supported by the callee, DL_CONNECT_CON is unchanged. The UNIX error returned may be set to (not limited to establish a data link connection. However, if the connect request is accepted by the DLS provider.
Format The message consists of service parameters contained invalid values. DL_ACCESS
The DLS...
HP DLPI Programmer's Guide - Page 135
...DL_SYSERR
A system error has occurred and the UNIX system error is indicated in Table 2-2 on the stream where the DL_CONNECT_RES primitive was not supported by the ...errors listed in the DL_ERROR_ACK. The UNIX error returned may only be set to (not limited to a pending connect indication. If the current stream and responding stream are the same, the resulting state of service...
HP DLPI Programmer's Guide - Page 177
...driver parameters.
uint32_t
dl_mtu;
dl_speed
Speed of this request between the driver's user space application and the driver.
• The DL_HP_SERIALIZE bit is ignored for DL_HP_GET_DRV_PARAM_IOCTL.
• The drivers...uint64_t
dl_value3; Chapter 3
DLPI Input/Output Controls Supported ioctls
DL_HP_GET_DRV_PARAM_IOCTL
DL_HP_GET_DRV_PARAM_IOCTL is a DLPI defined transparent ...
HP DLPI Programmer's Guide - Page 11
... be issued between editions to the appropriate product support service. See your HP sales representative for HP-UX 11i. To ensure that you receive the updated or new editions, you should subscribe to correct errors or document product changes.
The document printing date and part number indicate the document's current edition. Minor changes may be made . The...
HP DLPI Programmer's Guide - Page 20
... that defines the protocol through which layer the services are used throughout this guide. The model is described in the OSI Reference Model) is presented here to identify different components of that are
provided.
20
Chapter 1 A model of the data link layer is responsible for the transmission and error-free delivery of bits of information over...
HP DLPI Programmer's Guide - Page 38
... and failure with a DL_ERROR_ACK message. The provider indicates success with a DL_OK_ACK message and failure with a DL_ERROR_ACK message.
Introduction to DLPI DLPI Services
Figure 1-8
DL_ENABMULTI_REQ requests the DLS provider to enable specific multicast addresses on a per stream basis, either at the physical level or at the SAP level. The normal message sequence is...
HP DLPI Programmer's Guide - Page 132
...error returned may be set to (not limited to) errors listed in the DL_ERROR_ACK. DL_SYSERR
A system error has occurred and the UNIX system error is indicated in Table 2-2 on page 71. Format The message consists of service parameters contained invalid values. Reasons for Failure DL_BADADDR
The destination DLSAP address was not supported... Connection-mode Service Primitives
Response There is ...
HP DLPI Programmer's Guide - Page 136
... UNIX error returned may only be set to (not limited to the only outstanding connect indication.
These streams may be the same when the response corresponds to ) errors listed in a valid state for the responding stream was not supported by the parameter dl_res_token), the resulting state is DL_DATAXFER. DLPI Primitives Connection-mode Service Primitives
DL_INCON_PENDING...
HP DLPI Programmer's Guide - Page 179
... note the following points:
• DLPI does not interpret the request of the underlying link in Mbits/sec. uint32_t
dl_reserved1[2]; Chapter 3
DLPI Input/Output Controls Supported ioctls
DL_HP_GET_DRV_PARAM_IOCTL
DL_HP_GET_DRV_PARAM_IOCTL is ignored for DL_HP_GET_DRV_PARAM_IOCTL.
• The drivers can define their own dl_request by DLPI. Before using other bits that retrieves the...
System Firmware Matrixes - Minimum Firmware Requirements for HP-UX 11i v3, 11i v2 and PCI I/O Adapters - Page 4
...'s Guide under the System Firmware section of updating firmware.
The method to :
feedback@fc.hp.com
Include the document title, manufacturing part number, and any errors found , or suggestion for improvement, or compliments to use the CD to HP-UX 11i v3. Send any comment, error found , suggestions for improvement you update to the latest firmware available before installing...
HP Firmware Manager User's Guide - Page 32
... to an update program error, version error, a problem with the device, trouble reading the disk, an unexpected system reset, or a problem with shared firmware components, followed by firmware for assistance.
[EXECUTED]
The update program does not return status codes indicating whether the update was successful, select OK, then revisit the Manage Firmware screen and verify that the Installed...
HP A180 Reviews
We have not received any reviews for HP yet.