Hayward HPC-4 Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward HPC-4 manuals!
Problems with Hayward HPC-4?
Ask a Question
Free Hayward HPC-4 manuals!
Problems with Hayward HPC-4?
Ask a Question
Popular Hayward HPC-4 Manual Pages
Model: ALL MODELS Installation - Page 2
... all AC power during installation.
•
! To... for US models (two for Canadian models) is located...INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS
When using this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 3 meters of 100 degrees Fahrenheit may be connected to the grounding means provided in the electric supply service...
Model: ALL MODELS Installation - Page 4
... on each installation step are included with HPC-4-RC, HPC-4-ACT-RC)
AQL-DIM
Light Dimmer Relay
GVA-24
Valve Actuator
V&A-xx
Valve & Actuator (xx=1P (1.5" pos. Plumbing (page 4) General Pool Equipment
5. Electrical Wiring (page 6) Main service Grounding and bonding Circuit breakers ECOMMAND 4 control power 1 seal), (Included with HPC-4-ACT,
HPC-4-ACT-RC)
Installation Steps
Details...
Model: ALL MODELS Installation - Page 5
... is exposed to be installed on a flat surface with insulation and white paint.
The AQL2-SS-RF is a waterproof portable remote control that is designed to the same sunlight as a heat sink (disperses heat from the pool/spa (or more, if local codes require). 1. Mounting the Equipment
ECOMMAND 4 Control Center
The ECOMMAND 4 is contained in doubt...
Model: ALL MODELS Installation - Page 11
... must be off to the VSC), the ECOMMAND 4 will be connected to most heaters also include specific wiring instructions for general purpose use (solar, water feature, in-floor cleaner, etc.). When the filter pump output is compatible with 24V control circuits. Hayward Variable Speed Filter Pump: Proper installation of low voltage dry contacts that contains a valve...
Model: ALL MODELS Installation - Page 15
... should be used to control a solar heating system, the solar sensor is required, contact the Goldline service dept.
Temperature Sensors The ECOMMAND 4 utilizes 10K ohm thermistor type sensors. The sensors are included.
for information on setting the pump address.
cable.
Hayward Variable Speed Filter Pump: Refer to the diagram below for installation information.
Model: ALL MODELS Installation - Page 17
...Goldline Aqua Rite or Hayward Swimpure chlorinator), the ECOMMAND 4 will automatically chlorinate both the pool and spa according to fix the configuration. If disabled (default), all displays relating to operate. Configuration information is entered at the keypad and "tells" the ECOMMAND 4 what equipment is installed in the system (see Settings Menu in the Operation manual).
Model: ALL MODELS Installation - Page 19
... . Filter Off Valve Change This menu appears only if Pool/Spa setup is set to the pump. Std".
When the filter pump output is off ...ECOMMAND 4 will switch the pool/spa valves to control the low speed motor winding on the pump. For the Hayward Tristar variable speed pump: The Filter relay is used as the lower limit in the Installation manual for specific information regarding the control...
Model: ALL MODELS Installation - Page 27
... through the heater. • The heater temperature setting is properly grounded and bonded. 4. The ECOMMAND 4 is set to the heater manual and also "Heater Control" (page 8). • Heater is turned on ("Kill Switch" is in order for the heater to fire. Program Automatic Operation
Refer to NEC and local codes. 3. If the "Heater" LED is enabled...
Model: ALL MODELS Installation - Page 28
... will turn outputs off at the main display (only). Push the SERVICE button once more detailed instructions on /off and then allow you to the Operation Manual. Heater control outputs and solar control outputs are prevented from turning on . Service Mode Service mode disables all outputs off manually at the end of the "Filter" button). • The heater...
Model: ALL MODELS Installation - Page 31
... service.
Problems resulting from improper installation including installation on authorized service centers please contact the Hayward/Goldline Technical Service Support...code will be free of defects in the owners manual(s).
5. NO WHOLESALER, AGENT, DEALER, CONTRACTOR OR OTHER PERSON IS AUTHORIZED TO GIVE ANY WARRANTY ON BEHALF OF GOLDLINE. To obtain warranty service or repair...
Model: ALL MODELS Operation - Page 2
...service... installed ...models) is provided on this unit to connect a minimum 8 AWG (8.4 mm2) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 3 meters of 100 degrees Fahrenheit may be followed, including the following:
• READ AND FOLLOW ALL INSTRUCTIONS
•
! IMPORTANT SAFETY INSTRUCTIONS...
Model: ALL MODELS Operation - Page 9
... logic that are in troubleshooting, if problems occur. The "Diagnostic Menu" is less than the desired temperature setting.
The ECOMMAND 4 will automatically switch to previous/next menu item
The spa solar setting will only appear if the system has been setup for "spa only" or "pool and spa" operation and the solar control is enabled. The heater...
Model: ALL MODELS Operation - Page 19
... temperature settings. If...setting AND the solar sensor is on , it will continue to next menu item or previous/next configuration menu
Solar If the solar control...setting (see Settings Menu).
If solar is operated by a pump, then one of the AUX relays must be setup...set up to turn on . The desired temperature is operated by a valve, then the Valve3 output must be installed...
Model: ALL MODELS Operation - Page 28
...setting must be set greater than one reason, in the ECOMMAND..., require replacement. For ... Hayward/Goldline Technical Service ...error messages are: • PCB Error • Low Salt/Amps/Minerals • High Salt/Amps/Minerals • Test Salt Level (Test Minerals) Refer to the Aqua Rite or Swimpure manual to previous/next menu item
Salt level of the sensor. If the problem is used
Set...
Model: ALL MODELS Operation - Page 31
... STATE. For more information on authorized service centers please contact the Hayward/Goldline Technical Service Support Center ( 61 Whitecap Road, North Kingstown RI, 02852) or visit the Goldline web site, www.goldlinecontrols.com. Material supplied or workmanship performed by others in the owners manual(s).
5. Problems resulting from failure to install, operate or maintain the product(s) in...
Hayward HPC-4 Reviews
We have not received any reviews for Hayward yet.