Hayward EcoStar C Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward EcoStar C manuals!
Problems with Hayward EcoStar C?
Ask a Question
Free Hayward EcoStar C manuals!
Problems with Hayward EcoStar C?
Ask a Question
Popular Hayward EcoStar C Manual Pages
EcoStar® Manual - Page 18
Configuration Menu Locked
Configuration Menu press > to next item Time: Th 1:27PM
+ change or > skip
Set Day and Time Thursday 1:27p
Speed Selection rpm
MAX allowed speed 3450 (600-3450rpm)
MIN allowed speed 600 (600-3450rpm)
Set max-speed Prime Period: Auto Sense
Remote Control Mode Standalone/Hayward
Set COMM Bus Address Pool Filter to adjust, > go to enter
Use + / -
EcoStar C Digital Control Interface Manual IS3400VSPC - Page 1
... to set selected password character Move to next password character
Note: When password protection is not confirmed correctly, then the user will respond to any of time from the pool control. Password Protection Disabled
Buttons Used
+
Comments
Use to enable or disable password protection Move to EcoStar Pump Owner's Guide (IS3400VSP) for all commands being controlled by a Hayward...
Technical Guide - Page 12
... not compatible) v2.80 or higher
2
3
Figure 22
4
Note: Wire from
4 on
7
EcoStar is data connected to a Hayward/Goldline control, voltage
needs to point. Installation-Hayward/Goldline Controls
(Compatible software shown below)
1. Wire 7 on the pump to 2 on the controller, 8 on the pump to 3 on the controller and 1 on the pump to 4 to 1 on Remote
display to
the...
Technical Guide - Page 18
Press the button (fig 32) to the pump, the pump model will have default setting of 1750 RPM (50%), 7 days a week from 12:00 am - 11:45 pm.
2.
When power is changed or set as shown to unlock and enter the Configuration menu (fig
33). Timer 1 will display, then the following screens (fig 31 & 32). Fig...
Technical Guide - Page 19
Press the button to enter the Configuration Menu (fig 34).
5. Programming-Configuration
4.
Fig 34
Fig 35 Page 17 On the next screen you will tell you how to use the & buttons to adjust, and the to go to the next item (fig 35). On the next screen it will be asked to press the button to continue.
Technical Guide - Page 23
... controls including third party models) (fig 43 & 44). Use the & buttons to continue.
12. You will now see the max-speed Prime period. Press & buttons for Auto Sense (3000 RPM), or a 3 min (max set speed) prime period (fig 42).This function only works in Standalone and Relay Control modes. Press the button to continue .
Programming-Configuration...
Technical Guide - Page 26
... time clock perimeters.
If yes, press and confirm on setting password protection. If no, press the button to continue. Otherwise continue with this point you have an HCP3400VSP or HCP3400VSPVR commercial EcoStar please refer to page 39 for directions on the next screen. Programming-Configuration
If you will be the next to program. At...
Technical Guide - Page 27
... bus address needs to be changed as relays on control connected pumps. Press the button until you see the Timers Menu (fig 51). Programming-Timers
Stand alone/Hayward Stand alone:
Both times and speeds need to be set as needed. . Relay Control
Only requires that speed be set in Configuration.
1. Press the button to run the pump if the...
Technical Guide - Page 42
... on the pump, or by resetting all parameters in the Configuration menu. Models HCP3400VSP and HCP3400VSPVR
Page 40 Resume configuration on page 24
System Locked Password: 0____
Figure 80
Figure 81
Figure 82
Note: If the password has been changed it may be asked to confirm the password. When you press any key other than the Stop...
Technical Guide - Page 44
... (page 36). Clear all debris from lead to ground. Troubleshooting/Fault Codes
This guide will cover only those problems with priming problems are addressed in the owners manual. PFC Circuit Hi
Drive Error! Check incoming line voltage (page 4) and verify that the internal components of 230 VAC. Code/Fault
Indications
Drive Error! Check fan and shroud for issues. All other pump...
Technical Guide - Page 45
... (page 4) and verify that it is correct and error still occurs, replace drive. Check incoming supply voltage, if greater than 264 VAC, refer to Hayward Service Bulletin "Pump Error: Ac Volts too High" and follow instructions for blockage. Check fan and shroud for registry change , replace drive. If error still occurs, replace drive. Indicates that the heatsink on the bottom of...
Technical Guide - Page 46
... and drive. If any of these readings are connected correctly (page 10). Troubleshooting/Fault Codes
Code/Fault
Drive Error Drive failed to start the motor. If no continuity.
If error still exists remove all (0) check connection between terminal 1 with EcoStar and terminal 4 with Hayward/Goldline Control (page 10).
If pump is displayed. There should be sure motor shaft...
Technical Guide - Page 48
... Clemmons Tech Service for isolator.
It travels on the comm. If the values are correct, replace the drive. Control reads "Pool bridge comm"
This indicates interference on the comm. This is connected to a GL/Hayward control. The breaker is tripping.
Page 46 If not, replace motor. Check input wiring and breaker. Troubleshooting/Fault Codes
Code/Fault
Indications
Warning...
Technical Guide - Page 49
... are on control display.
Troubleshooting/Fault Codes
Code/Fault
Indications
EcoStar is connected and configured to operate with the settings in the control (page 20)
EcoStar reverts to Standalone mode even when properly connected to
the GL/Hayward control.
Check comm. Be sure EcoStar is configured for relay control (page 10) . No error on the EcoStar comm. EcoStar is set to...
Technical Guide - Page 50
...
Menu button is actually for relay control.
The EcoStar is causing other equipment from the control are connected in the EcoStar does not work . Remove wires and connect to the pump, the
EcoStar interface reads "Remote Stop Engaged". If problem persists, purchase (2) model XPF 20A 3-wire noise filters through X-10 website. This is connected and operating via the GL/Hayward...
Hayward EcoStar C Reviews
We have not received any reviews for Hayward yet.