Harbor Freight Tools 67450 - 11 Gauge Coil Roofing Nailer Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 67450 manuals!
Problems with Harbor Freight Tools 67450?
Ask a Question
Free Harbor Freight Tools 67450 manuals!
Problems with Harbor Freight Tools 67450?
Ask a Question
Popular Harbor Freight Tools 67450 Manual Pages
User Manual - Page 2
...pipe thread, straight
WARNING marking concerning Risk of Respiratory Injury. Read the manual before set-up and/or use.
Item 67450
MAINTENANCE Indicates a hazardous situation which... marking concerning Risk of Contents
Safety 2 Specifications 7 Setup 8 Operation 12
Maintenance 16 Parts List and Diagram 18 Warranty 20
SAFETY
SETUP
OPERATION
WARNING SYMBOLS AND DEFINITIONS This is ...
User Manual - Page 4
... gases are caused by qualified repair personnel. SAFETY
SETUP
Tool use only identical replacement parts. Any tool that are able to persons. A properly maintained tool reduces the risk of the tool or serious injury to result in the Specifications chart of injury to persons. If damaged, have the tool serviced before making adjustments, doing tool maintenance...
User Manual - Page 5
...defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.)
26. Do not drive...repair. Always disconnect air supply when moving the tool. Check manual for the air compressor used to enforce the use . Unattended. SAFETY
SETUP
Specific Safety Instructions...California] to avoid weakening it .
21. Install an in-line shutoff valve to allow immediate...
User Manual - Page 6
... or pull tool up using vibrating tools regularly or for working on the user.
4. SETUP
OPERATION
MAINTENANCE
Page 6
For technical questions, please call 1-800-444-3353. Repeated or ... not use this manual.
Do not smoke during use. Do not allow anyone under 18 years old in your hand or transport tool to ensure medical problems are not being...during use. SAVE THESE INSTRUCTIONS.
User Manual - Page 8
... instructions that follow. This operation is aware of this manual.... Hold down Spring and Lever while placing Trigger over end of this product. This operation is safer and should use contact trip / bump fire operation.
4.
Rubber Ring
Spring
Lever
Figure C: Installing Trigger
5. Remove Spring and store unused Trigger in a safe direction, and release pressure before set...
User Manual - Page 9
SAFETY
SETUP
Air Supply
TO PREVENT...FROM ACCIDENTAL OPERATION: Do not install a female quick coupler on the air compressor according to prevent accidental operation. Inspect the air connections for best service, as a power source ... the tool is ruptured. Repair any other bottled gas as shown on Figure E on page 10 and Figure F on page 11.
The air pressure setting must not exceed 90 PSI...
User Manual - Page 11
... air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool
MAINTENANCE
OPERATION
SETUP
SAFETY
Page 11 Figure F: Stationary Air Supply Setup
Item 67450
For technical questions, please call 1-800-444-3353.
User Manual - Page 12
... route to pulling the Trigger. If any problems are depressed again. Test the tool by a qualified service technician.
Designate a work area with enough extra length to possible damage. The tool should return to the tool and set up or use , looking for damaged, loose, and missing parts. The tool must be hazardous objects (such...
User Manual - Page 13
...tool must cycle (fire) again only once. If it cycles (fires), stop immediately and have it repaired by a qualified service technician. SETUP
OPERATION
MAINTENANCE
Item 67450
For technical questions, please call 1-800-444-3353. Point the tool at ... again. The tool should return to the tool and set within the Operating Air Pressure indicated on the Specification chart.
5.
User Manual - Page 14
... Between 3/4″ and 1″ Long Nails (Use top setting). Between 1″ and 1-1/4″ Long Nails (Use middle setting). Between 1-1/4″ and 1-3/4″ Long Nails (Use bottom setting). Swing the Canister Cover (89) closed.
6.
Push down...Place a coil of firing any fasteners.
1. C. SETUP
OPERATION
MAINTENANCE
Page 14
For technical questions, please call 1-800-444-3353.
User Manual - Page 15
...the Tool into the cylinder. b. SHINGLE SPACING
(bottom view)
Screw (80)
Shingle Guide
(79)
WARNING! TO PREVENT SERIOUS INJURY: Keep second hand away from tool discharge ... of firing any fasteners.
Then, retighten the Screw. b. SAFETY
SETUP
General Operating Instructions
1. Shingle Guide Setup: The Shingle Guide (79) controls roof shingle spacing. c. Clean external surfaces with clean...
User Manual - Page 16
... is incapable of firing any fasteners.
• Empty the magazine and leave it open during service. Performing routine maintenance on the air supply according to the tool if reused.
3.
SAFETY
SETUP
User-Maintenance Instructions
Procedures not specifically explained in this manual must be performed only by a qualified technician.
Page 16
For technical questions, please call...
User Manual - Page 17
... and replace damaged parts before service. Disconnect air supply before use. 2. Severe air leakage. (Slight air leakage is providing enough air flow (CFM) and pressure (PSI) to the tool's air inlet. Incorrect tool depth setting. 2. Damaged valve or housing. 4. Adjust depth setting, if available. 2. Adjust depth setting, if available. 2.
SAFETY
SETUP
Troubleshooting
Problem...
User Manual - Page 18
...
74 Screw
75 Nut
76 Washer
77 Connecting Plate
78 Support
79 Bracket
80 Screw
81 Screw
82 Nail Canister
83 ...PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. Item 67450 THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS...
User Manual - Page 19
Page 19
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Assembly Diagram
SAFETY
SETUP
OPERATION
MAINTENANCE
Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.
Item 67450
For technical questions, please call 1-800-444-3353.
Harbor Freight Tools 67450 Reviews
We have not received any reviews for Harbor Freight Tools yet.