Harbor Freight Tools 61415 - 8 HP OHV Horizontal Shaft Gas Engine EPA Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
This item is in your list!
View All Support Options Below
Free Harbor Freight Tools 61415 manuals!
Problems with Harbor Freight Tools 61415?
Ask a Question
Free Harbor Freight Tools 61415 manuals!
Problems with Harbor Freight Tools 61415?
Ask a Question
Popular Harbor Freight Tools 61415 Manual Pages
User Manual - Page 2
... is warranted for this manual. For warranty information, refer to the last pages of Contents
Specifications 2 Safety 3 Setup 6 Operation 8
Maintenance 12 Troubleshooting 16 Warranties 18 Parts Lists and Diagrams 20
Specifications
Displacement
Engine Type
Cooling ...7/16″ - 20 UNF
The emissions control system for standards set by the U.S.
Environmental Protection Agency.
User Manual - Page 3
...windows, doors, and vents. It must be built into this manual cannot cover all instructions. SAFETY
SETUp
WARNING SYMBOLS AND DEFINITIONS This is used to alert you to ... personal injury.
IMpORTANT SAFETY INSTRUCTIONS
WARNING! Indicates a hazardous situation which cannot be supplied by the operator. Wear hearing protection.
Read the manual before set-up and/or use.
...
User Manual - Page 4
...for your model. Use only lubricants and fuel ...parts.
19.
Do not touch engine during use OUTSIDE and far away from the Engine during operation.
20. Do not operate in explosive atmospheres, such as in the Specifications... questions, please call 1-800-520-0882. Operation of this manual. Only use . Keep all times. People with sufficient weight...SETUp
Set up .
6.
User Manual - Page 5
...equipment maintenance. Refuel in this manual or any spilled fuel and ...Only a qualified service technician may adjust parts that you are caused by a qualified repair person using ...instructions and in a bottom-ventilated, covered, metal container.
25. If unreadable or missing, contact Harbor Freight Tools for a replacement.
6. Store equipment out of the reach of parts, and any service...
User Manual - Page 6
... WARNING! WARNING! Components and Controls
Air Cleaner
Fuel Cap
SETUp
OpERATION
Oil Drain plug
Starter Handle
Muffler
Throttle
Choke
Fuel ...INSTALL THIS ENGINE ACCORDING TO EQUIpMENT INSTRUCTIONS BEFORE USE. ITEM 61415
MAINTENANCE
SAFETY
Set Up
Read the ENTIRE IMpORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set...
User Manual - Page 8
... engine is stopped and is at the proper level.
SETUp
OpERATION
MAINTENANCE
Page 8
For technical questions, please call 1-800-520-0882. SAFETY
Operation
Read the ENTIRE IMpORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up and starting. Do not run the engine with...
User Manual - Page 9
...Inspect the equipment and engine. d. Follow the Set Up Instructions in the air. Fill the engine with 87 ...remove the Fuel Cap.
3. Then replace the Strainer. Starting the Engine
Before Starting the ...fuel hangs in the equipment manual to enter the carburetor, affecting engine performance and...the engine off and wait for it .
2. SETUp
OpERATION
MAINTENANCE
ITEM 61415
For technical questions, please...
User Manual - Page 10
.... To restart a warm engine, leave the Choke in place of the Engine loosely and pull
it as the
Throttle. Open the Fuel Valve.
1
START RUN
2
SETUp
OpERATION
3. Repeat until resistance is so equipped.
4.
Page 10
For technical questions, please call 1-800-520-0882. SAFETY...
User Manual - Page 12
... Follow all service instructions in this manual, will differ depending on factors such as part of the ...Replace fuel line if necessary
Before Each Use
Monthly or every 20 hr. or Every 6 mo. ITEM 61415 Check/adjust idle speed 2. SAFETY
SETUp...service the equipment instead. Cleaning, Maintenance, and Lubrication Schedule
Note: This maintenance schedule is intended solely as a general guide...
User Manual - Page 15
...drained, reinstall the drain bolt and sediment cup (if equipped). c. LUBRICATION:
a.
c. SETUp
OpERATION
MAINTENANCE
ITEM 61415
For technical questions, please call 1-800-520-0882. Place a ... STORAGE AREA: Cover and store in cylinder.
Do not smoke. After all metal parts.
2. Replace spark plug, but leave spark plug cap disconnected.
Page 15
Change engine oil. Remove...
User Manual - Page 16
SAFETY
SETUp
Troubleshooting
problem
possible Causes
Engine will occur when trying to start.)
3. Gasoline with ...problem, replace head gasket.
4. Have qualified technician adjust/ repair valves and tappets.
Too much fuel in the air.
8. Turn Choke to START position.
9. Replace spark plug cap.
5. Tighten head.
Follow all safety precautions whenever diagnosing or servicing ...
User Manual - Page 17
... questions, please call 1-800-520-0882. SAFETY
SETUp
problem
Engine misfires
possible Causes
1. Incorrect spark plug gap or
damaged spark plug. 3. Replace spark plug cap. 4. Intake valve stuck or overheated engine. 4. Use cold weather fuel and oil additives to proper level. Have qualified technician diagnose and service engine.
4. Defective spark plug cap. 4. Secure spark...
User Manual - Page 18
...is defective, the part will either repair or replace the product at our election or we may not apply to you should contact the Harbor Freight Tools Customer Service Department at no...your engine to you may include parts such as a problem exists. Owner's Warranty Responsibilities
• As the engine owner, you warranty coverage if your Owner's Manual.
Also included may deny you...
User Manual - Page 19
... equipped) i) Exhaust pipe stud. ii) Muffler.
No Charge Repair or Replacement Repair or replacement of any warranted parts
e) Repairs performed outside of Coverage HFT warrants to a first retail purchaser and each subsequent purchaser that the engine is damaged due to failure to follow the maintenance and operating instructions set forth in durability and performance, may be performed at...
User Manual - Page 20
ITEM 61415
SAFETY
SETUp
parts Lists and Diagrams
parts List
part
Description
1 Head Subassembly, Cylinder
2 Plug, Spark
3 Bolt, Cylinder Head
4 Pin
5 Gasket, Cylinder Head
6 Cover Subassembly, Cylinder Head
7 Gasket, Cylinder Head Cover
8 Tube, Breather
9 Bolt Subassembly, Cylinder Head Cover
10 Washer Set
11 Stud
12 Stud
13 Crankcase Subassembly
14 Seal, Oil
15 Sensor, ...
Harbor Freight Tools 61415 Reviews
Do you have an experience with the Harbor Freight Tools 61415 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Harbor Freight Tools yet.
Earn 750 points for your review!