Haier PGT2.0-2 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier PGT2.0-2 manuals!
Problems with Haier PGT2.0-2?
Ask a Question
Free Haier PGT2.0-2 manuals!
Problems with Haier PGT2.0-2?
Ask a Question
Popular Haier PGT2.0-2 Manual Pages
User Manual - Page 1
Haier flat panel solar collector Installation manual
Model：
PGT2.0-2
Prepared by： Qingdao economic and technology development zone Haier water
heater company
Prepared date： 2009.02.18
1
User Manual - Page 3
...the plate collector
Model
Light receiving
area (m2)
Exterior size (mm)
Net weight (kg)
Gross weight (kg)
PGT2.0-2
1.9
2000*1020*84
40
43
Maximum loadability of the plate collector: without being damaged by the test pressure of the plate collector
1. Instruction manual for the ...The coarseness of the inner wall of the draining pipe and collecting pipe for collector installation
I.
User Manual - Page 5
... energy. The 16 holes (φ9) above are connected correctly, and that must be solved; Pure water is recommended to use the primary circulation system, the problem with the scaling in any season and the
antifreeze could be used as the heat conducting medium. The table below );
5
User Manual - Page 7
...Allow the liquid filling pump to fill antifreeze; Check the system regularly to be replaced, it operates properly; The liquids in the same directions for filling the liquid must...（Attention, the replacement should also be cleaned before filling the antifreeze; check the manometer to prevent overheating of the system by the local after-service providers）. 4. ...
User Manual - Page 9
... with equipotential bonding. For the connection material, connection and anti-corrosion method, the local specifications about the lightning system designing shall be protected, the frame mounted on a wall;
9... material, connection and anti-corrosion method, the local specifications about the lightning system designing shall be protected, making a lightning rod is well
protected by ...
User Manual - Page 19
..., the top of the foundation for the collector （1）Mounting steps
19 How to mount the collector on flat roof
1. How to mount the support for the collector shall be a field casting concrete frusta or concrete brick.
User Manual - Page 20
...the antirust paint on it to prevent corrosion. Step 4: Anti-corrosion treatment: When the support is finished, treat it with hot galvanizing or paint it twice and apply finish paint ... 2 and 3 a triangle frame with expansion bolt; 1: Bottom rod of the support 2: Vertical rod of the support 3: Tilted rod of the support 4 and 7: Bolt 5 and 8: Nut 6: Channel steel 9:Collector fixing hook Step...
User Manual - Page 22
the upper edge of the collector with a bolt. Sample drawing for the mounted collector
22 Step 2: Tighten all bolts.
4. Step 1: Fix the collector onto the assembled support, clutch the lower edge of the collector shall be fixed through the fixing hole on its outer frame. Connect the plate collector to the fixed channel steel with the collector fixing hook;
User Manual - Page 24
... the wall body, such as deforming or cracks, etc. The light-weight filled wall shall not be used as a structure to support the solar collector. The support of anticorrosion. There are two ways for mounting the collector on the angle between the plate collector and the external wall. ● Mount...
User Manual - Page 28
1: Support frame 6: Plate collector
2: Front support 7: Bolt
3: Support connecting rod 4: Expansion bolt 5:Bolt
28
User Manual - Page 29
...been assembled in step 1 onto the external wall; I
An角g钢le支iro架n support plate heat colle平cto板r 集热M器8 bMo8lt螺栓
I
M8 expansMio8n膨b&#...wall and insert expansion bolt 4 into the holes;
tighten and fix them; Step 1: Make support 1, 2 and 3 of the collector with angle steel as per the drawing above and assemble...
User Manual - Page 31
Name
Qty
Specification
1
卡套 Stopper
2 sets
Connect one end to the copper pipe（￠ 22） and the other end is
G1/2 male thread
200mm long; and two end interfaces are
4
Bellows
2
G1/2 female thread nut
5
Tee-joint
2
G1/2 female thread to the copper pipe
3
卡套 connector
6 sets
（￠22...
User Manual - Page 34
The pipes and fittings shall be connected in parallel and then assemble two sets of the connected collectors in the same way for mounting two collectors above.
34 The 3rd Method: The kind of array of the collector needs less mounting area, but first two collectors shall be mounted in parallel too.
User Manual - Page 35
... or 4th method is recommended. It is not
recommended, i.e. To connect the collectors, connect two of them in parallel first and then assemble two sets of the collector needs less mounting area. The 4th Method: The kind of array of the connected collectors in parallel, i.e.
Haier PGT2.0-2 Reviews
We have not received any reviews for Haier yet.