Haier IT9002 1 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier IT9002 1 manuals!
Problems with Haier IT9002 1?
Ask a Question
Free Haier IT9002 1 manuals!
Problems with Haier IT9002 1?
Ask a Question
Popular Haier IT9002 1 Manual Pages
User Manual - Page 1
Service Manual
User Manual - Page 2
IT9002
Cooker Hood
INSTALLATION AND USER'S MANUAL
User Manual - Page 3
... replacement.
• The cooker hood must be installed in accordance with the installation
instructions and all measurements followed.
• All installation work must be replaced by the manufacturer, its
service ... during
installation and cleaning.
• When installing the cooker hood, make sure that the following recommended distances
between the top of cooker and the lowest part of the...
User Manual - Page 4
... old should any external covers be removed for servicing or maintenance except by suitably qualified personnel
Appliance information:
Please enter the details on the hob and the lowest part of the range hood.
(When the range hood is located above a gas appliance, this instruction manual carefully before installation and usage. There shall be discharged into...
User Manual - Page 5
... upper and lower parts)
(3) Hose connector
(4) Upper wall bracket
(5) Lower wall bracket
(6) ø 4mm x 10mm Screw (6 pcs)
2
(7) Washer (2 pcs)
(8) Wall plug (8 pcs)
(9) ø 4mm x 35mm Screw (8 pcs)
3
(10)
Exhaust hose (ø15cm)
(11) Carbon filter (required for circulating air mode)
4
(12)
Cable tie
5
6
7 8
Technical specifications
Model
Voltage Product dimension...
User Manual - Page 7
Installation (for the gas hob specify a greater distance, this has to be installed above an electric hob or a gas hob, the minimum distance between the hob and cooker hood must exceed 700mm. If the instructions for installation for venting outside)
When the cooker hood is to be measured from the top of the burners The height should be taken into account.
User Manual - Page 8
Fig. 9
Fig. 10 Installation (for venting outside)
Tools required
Mark wall as required (see Fig. 6)
8
Fig. 5 Drill holes for mounting the body. Fig. 6
Fix support plate on the wall by screws with expanding plugs.
Fig. 7 Secure hood (tighten all screws).
10mm
Fig. 8 Fit ducting adaptor.
User Manual - Page 10
... )".
Check with your cooker hood, you do not have an outlet for exhausting air, the exhaust hose (part [10]) is not required, and the installation is similar to the one shown in the section "Installation (for replacement.
8 To ensure best performance of your locad retailer or dealer to buy new carbon filters for venting...
User Manual - Page 11
...to low and finally o . Using your extractor, press and hold the key for 2 seconds.
Once set the fan motor to turn on , the display will show the symbol .
9 When the lights ...are on /o the extractor. The display will show the symbol flashing for 5 seconds whilst setting the time. Light Key
• Press the key to high speed.
Adjusting the Fan Speed
• ...
User Manual - Page 12
... button on the handle and then pull down on the filter at the front as shown in Fig. 14.1. After rinsing and drying the filter, replace it as shown in Fig. 14.2. You can also wash the grease filter in a dishwasher, ensuring that you should remove and clean the grease filter...
User Manual - Page 13
..., please contact your local or regional authorities. energy use) of the cooking process).
(13)
Install the cooker hood in a proper place where there is not shown in a way which is ...Information for dismantling Do not dismantle the appliance in the user manual. At the end of life, the appliance should not be supported by user.
Information for cooker hood
ENVIRONMENTAL PROTECTION:
This ...
User Manual - Page 14
....
1. Adjust hood installation height
as user manual. 3. No operation on fan speed button.
1. Enlarge common venting hole
diameter to adjust suction. 2. Troubleshooting
Failure
Root cause
Corrective action
No power
No work or voltage is burnt down.
1. Make sure power supply works normally or call electrician for fan.
3. Replace fan (please call
service center)
1. Power...
User Manual - Page 17
Then repair fan and motor.
8. Remove 8 screws from damper and 4 screws from reverse side of body to take out cover sheet.
7. Then from air outlet. Maintainence cover Remove 12 screws to remove one M5 screw. Remove 4 screws to take out maintainence cover.
User Manual - Page 18
Switch 9.LED light and switch control wire Use flat screwdriver to remove LED light. Disconnect all responding wire
connectors for replacement.
10.
Haier IT9002 1 Reviews
We have not received any reviews for Haier yet.