Haier HW-18HA03 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier HW-18HA03 manuals!
Problems with Haier HW-18HA03?
Ask a Question
Free Haier HW-18HA03 manuals!
Problems with Haier HW-18HA03?
Ask a Question
Popular Haier HW-18HA03 Manual Pages
User Manual - Page 1
Remote Controlled Window Type Room Air Conditioner
OPERATION
MANUAL
HW-09CC03
HW-09CD03
cL-3
HW-09CA12
HW-12CA03
HW-12HA03
o
HW-12HAO4
HW-12eA03
HW-12eA04
HW-18HB03
AW094AAMBA
AW122AAACA
AW124AAMBA
HW-12CA13
• Please read this operation manual before using the air conditioner.
7465703 H
User Manual - Page 3
...run temporarily in Auto temp mode.)
For model: HW-12CA03 11W•12HAO3 AW122AAACA HW-I2CAI3 HW.I2HAO4 HW•18HBO) AW124AAMBA
2
Description of the parts
Machine body
HW-12CA01 HW-I2cA03 AW094AAMBA IlW.12CA13
For models: BW-1211A03 FIW•18HBO3 AWI 22AAACA
...them.)
Display panel
[Time indicator
Lights up when 'Timer switch is set on remote controller is lost or does not work.
User Manual - Page 4
... 1
Lights up when Timer switch is
sct on "ON-or "OFF" position. mode.
3 Description of the parts
For models: HW-09CCO3 HW-09CA12
Inlet grating of air
Outlet grating of air
Time Indicator
Lights up when Timer switch is set on "ON" or "OFF- Power indicator
0
Lights up when compressor %IMns runn ng. Operation mode...
User Manual - Page 6
... the part indicated by OPEN and slide the lid away from the controller.
2 Insert the dry batteries
Make sure the dry batteries arc set dry batteries...models.
Handing the Wireless Remote Controller
are
• When operating, point the signal sending head toward the signal receiver of the same brand
and type. 2) When the remote controller is not active after
dry batteries have been replaced...
User Manual - Page 8
... desired temp., by I C. button. LOW
Select desired setting. Cooling operation
I C.
don't restart until 3 minutes...MOOE F. •
Cautions:
To protect unit system. " 0 " Each press will increase temp.setting by using "TEMP." HI ---s-
AUTO -•- temp.setting will decrease temp.setting by I . " V " Each press will change quickly to your desired figure.
4. Select ...
User Manual - Page 11
... functions are the same.
1. Select operation mode Press the "MODE" button. Every time the button is no more than 20t after compressor has started for HW-I 2eA03,HW-I minute, Auxiliary Heat function starts: when room temperature is over 25'C or during defrosting. Stop Press ON/OFF button again.
).K.
User Manual - Page 12
... More details is illustrated in the
following order
r SLEEP - 0- a Only some of the models have elapsed.
setting will rise automatically by another IC and maintain at this function. Every time
the button is started...it will run in SLEEP
function according to operation mode. Sleep mode setting
1.
I
Press the "TIMER" button. In thy and fan mode, there is not
I ...
User Manual - Page 13
... is available within 1-12 Hrs. If it changes in the following order:
- it 's not started. BLANK I . Timer operation
With this function, unit will decrease time setting by Ihour.
L_ O 2
O I,
)
1
12 start or stop . "V" Each press will start it and select desired operation mode.
2. If the button is kept pressed,time...
User Manual - Page 14
.../downward air direction.
(As per the above picture). The "Operation" light is lost or damaged, you can be adjusted. The setting of the air direction
II :
Left/right adjusting
Vcrucal guide plate Honzontal put& plate
Put the "Louver" button on and the conditioner will automatically reset the timing, and cancel the former...
User Manual - Page 15
... pause for a long period, it is set to right "Open" position for a while after the unit staying
then begins to keep the indoor air fresh. OPEN
I I 24AAMBA, 11W-12CA13, HW-18HB03)
There's a handle at the lower...gets frost, the machine will resume running automatically. If the switch is set to left corner of the air outlet grating, which is switched off, the protection device will ...
User Manual - Page 17
...ends of the lower part of the conditioner with rubber lid and install water outlet pipe to the drain pan.
4. Block the bottom plate hole of the air inlet grating. install water outlet pipe ... pu, l,
it out from the air inlet grating.
/ Nip the air filter and lift for the model HW-09CA12, HW-09CC03)
I )
In this method, the accumulated condensed water in the Fig3.
3) Connect drain hose to...
User Manual - Page 18
... not pour water on the machine
shell completely.
17
In wiping, first twist
•
out the water in order to p prevent electric shock or mechanical
trouble.
0
Van'
0
Hot waterabove 40Cmay cause disoaloratitm of the shell or deformation.
Before cleaning please pull off the power plug. Maintenance
I-
User Manual - Page 19
... cooling/heating effect is started after stop, it will need about 3 minutes to re-start so as to repair, please first check the following:
Phenomenon
Reason
Switch on the machine but it does not work immediately. Is there direct sunlight in cooling? 3.
Trouble shooting
Before sending to prevent the fuse from break.
User Manual - Page 20
... can be blown to use specific power circuit. if the sunlight...of the conditioner are:
0 Name Manual Water outlet pipe Drain elbow
Rubber...Installation diagram It should be less than 295mm
I
4
1
2
19
Width of the installation position I. Select position where the structure is required. 5. sunshading device
is firm. 2. Installation instruction
Selection of the wall should be installed...
User Manual - Page 21
...
350
530
1-RV-12xxx
410
570
AW122AAACA
AW124AAMBA
HW-12CA13
HW-18xxx
438
670
2. Plug the water outlet pipe ...(see Fig. 3) (For cooling only type; Iron frame
Fig.! Width of the machine body slightly. Installation process
1. Make the wall hole or window hole (see the drain hole at the back of the ... condensed water to stable position by expansible screws.
3. set it tightly.
Haier HW-18HA03 Reviews
We have not received any reviews for Haier yet.