Haier HSU-07C03 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier HSU-07C03 manuals!
Problems with Haier HSU-07C03?
Ask a Question
Free Haier HSU-07C03 manuals!
Problems with Haier HSU-07C03?
Ask a Question
Popular Haier HSU-07C03 Manual Pages
User Manual - Page 3
... or H07RN-F
3. If the fuse on strong enough supporter.
11.The wiring diagram is attached inside the machine.... situation
I. After installation, the power plug should be easily reached.
7. The appliance is not intended to use by the manufacturer or its service agent
or a ...10.The appliance must be installed on PC board is broken please change it must be replaced by young children or infirm...
User Manual - Page 4
.... Operation mode indicator
Lightudspurincgompressor running switch(manual)
Usoendfltoyersutnnicinongoling whenroomtemp.isbelow16oC.
Remote signal receiver
bAeepinsgounidgseneratewdhen saignaflrormemotceontrolleirs received. Test running . Outdoor Unit
HSU-088M06 HSU-098M06 HSU-108M06 HSU-128M06
HSU-188M06 Don'utsieitnormaolperation.
Timer mode indicator
LightuwspheTnimeorperation...
User Manual - Page 5
.... Each press will become normal. Hints
After replacing with new batteries, remote controller will change quickly. SWING display AUTO
3. CLOCK Used to set auto fan direction. 16. Parts and Functions
Operation
Buttons and display of the remote controller.
1
5
6
2
7
3
8
9
4
10
ON/OFF
TEMP
11
MODE 12
18
SET 19
FAN 13
TIMER 20
14
SWING
CLOCK...
User Manual - Page 6
...
After replacing with new batteries, remote controller will become normal. like the following figure:
1
5
6
2
7
3
8
9
4
10
ON/OFF
TEMP
11
MODE 12
18 SET
19
...FAN 13
TIMER 20
14 SWING
CLOCK
15
21
SLEEP HEALTH 16
LOCK 17
RESET 22
1. TEMP display
11. RESET Used to reset the controller back to select AUTO run, COOL, DRY, HEAT and FAN operation
13. Parts...
User Manual - Page 7
... or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is supplied again. "
˜
∆
˜
µ
'
ø
Put on the indoor unit. Note: Use two new same-typed batteries when loading.
Power failure resume(please set and apply as illustrated. 2 R-03 batteries, resetting key (cylinder...
User Manual - Page 8
...starts. Note:AUTO is the
After replacing batteries, press ON/OFF, and display explanation of the displayed
becomes as follows:
ON/OFF
TEMP
MODE FAN
SET TIMER
SWING
CLOCK
SLEEP HEALTH
LOCK
...or "
"FAN.
(3) FAN
Press FAN button. Previous operation status appears on display. (Not Timer setting) Power indicator on LCD. To run it next time just
select the operation mode and it will ...
User Manual - Page 9
... 1oC Every time the button is not available. For each operation status. Ultra-loawifrlow
Unit runs at your desired mode.
(3) Select temp. Onreachingtemp.setting,unit will start
Press ON/OFF button, unit starts. Stop display at the speed displayed on LCD. Every time the button is pressed, temp. Previous ...
User Manual - Page 10
...LCD. Be careful not to system protection. difference is above 7oC. Temp. So, you'd better set a temp. conditioner to your fatigue. Vertical flap closes automatically. Hints
As cold air flows downward ... controller) Left and right air flow adjustment
Press SWING button, vertical flap will move within(manual)
the range shown in COOL mode. About 10o COOL About 45o
Cautions:
It is advisable...
User Manual - Page 11
...mode disappears. If button is pressed, display changes as previous one. After replacing batteries or a power failure happens, Time setting should be shown on LCD. TIMER ON/OFF
(1)After unit start or stop...within 24 hours.
Remote controller possesses memory function, when use TIMER mode next time, just press SET button after you fall asleep at x hour x min. (TIMER ON or TIMER OFF). Power...
User Manual - Page 12
... several times until TIMER mode disappears.
If button is kept depressed, time will change quickly. Time will be shown on LCD. "ON" will flash.
(3)Time setting for TIMER ON Press HOUR button. "ON" stops blinking, While "OFF" starts blinking. If button is kept depressed, time will change quickly. Power indicator on...
User Manual - Page 13
...in the test ioperatioPn when the room
temperature is also impossible to change the settings of this operation only when the remote controller is above 23oC. Heating when ...cooling operation starts with the air flow speed setting "Hi". i
P
Removal of the restriction of operation is defective or lost. When the remote controller is a model for more the emergency operation switch, or ...
User Manual - Page 14
.... Unit will not start running with the indicator lighting up , and 3 minutes later the compressor starts running unless 3 minutes have elapsed. setting
Fig.1
Unit stop
ON/OFF
TEMP
MODE
SET
FAN
TIMER
SWING
CLOCK
SLEEP HEALTH
LOCK
RESET
Power Failure Resume Function
If the unit is started for your sleep.(As shown...
User Manual - Page 15
... kill bacteria and speed up , but the anion generator does not release anion. Air conditioner starts health anion function operation.
ON/OFF
TEMP
MODE FAN
SET TIMER
SWING
CLOCK
SLEEP HEALTH
LOCK
RESET
2.Health anion function
Press HEALTH button.
User Manual - Page 16
...Use a vacuum cleaner to remove dust,or wash the filter with chemicals. Maintenance
Different models have different appearance
Cleaning of unit casing
Cleaning of remote controller
Cut off the detergent on...2.Remove air filter
Push up the filter's center tab
slightly until it with soft cloth. problems might occur.
In case of air filter
Don't use dry cloth. Make sure
that
the...
User Manual - Page 18
Trouble shooting
Before asking for 3 minutes to protect the air conditioner.
When the electric plug is heard ...air conditioner -7oC~43oC.
Is fuse blown out? Is temperature set correctly?
During COOL or DRY operation, indoor unit
may be heard. Is power plug inserted? Multiple check
Does not work for service, check the following first. Application temp. This is generated ...
Haier HSU-07C03 Reviews
We have not received any reviews for Haier yet.