Haier HA500TX Support and Manuals
Get Help and Manuals for this Haier item
This item is in your list!
View All Support Options Below
Free Haier HA500TX manuals!
Problems with Haier HA500TX?
Ask a Question
Free Haier HA500TX manuals!
Problems with Haier HA500TX?
Ask a Question
Popular Haier HA500TX Manual Pages
User Manual - Page 2
Technical Specification
Item Power supply
Model
Maximum working current (A)
Water pressure Washing power Spinning power
(MPa) (W) (W)
Washing program Washing capacity Heating power Size (HXDXW) Weight
(kg) (W) (mm) (kg)
HA600TX 220V~/50Hz 10 0.05 P 1 330 650 16 6 1950 850x550x595 72
14
User Manual - Page 3
Trouble shooting
The following circumstances do not stop
== Check that the height of the water hose is below 80cm
Drainage... less than 0.05MPa The inlet hose is kinked Water supply failure The program knob is not properly set The door is not properly closed
The water supply and drainage do not constitute problems. Do not contact the maintenance service until the problem has been confirmed.
User Manual - Page 4
...to the water supply or the ingress of moisture and odors. If the washing machine is replaced correctly to prevent the formation of the filter compartment cover to open the door slightly to ... is the reverse of the water and electricity supply after cleaning.
4. Unplug the machine during installation as shown below. Use a soft cloth dampened with soapy liquid to ensure that the filter...
User Manual - Page 5
... or minimal washing programs for heavily soiled clothes. 6. Do not use more detergent than required. 7. Selecting the function button
Select function buttons as required, otherwise, set at position * when heating is finished, press the power button again to the directions printed on the operation panel) ,otherwise keep all the button released...
User Manual - Page 6
... the program knob clockwise to both box 1 and 2; Push back the drawer gently. Washing program setting
Set the wash program correctly in the washing machine and then tightly close the door of the distributor on...damage artificial fabrics.
3. Caution: Turn off the power before setting the wash program.
10
Laundry loading
Evenly load the laundry in accordance with the laundry load.the ...
User Manual - Page 7
... should be used such as keys and coins.
-Clothing with reference to clothes labels.
9 Power supply
Plug in a wash bag or special bag before washing. -Repaire damaged clothing,lose buttons or damaged zips and hooks before washing. -Bed sheets and table ware should not be used . Water supply
Turn on the...
User Manual - Page 9
...
Press the button ,washing machine will working;release the button, the washing machine will illuminates when the power supply is recommended that only when the washer doesn't work again.
E No Soak Button
For the synthetics cycle and the wool cycle, push the button down, the anticrease funtion will be used .
ON...
User Manual - Page 10
... *. Control Panel
F
HN600TX
A Washing program
Turn the knob clockwise to set the desired wash program .
Temperatures between 30OC-90OC can be setted , Cold wash is se-
lected when the knob is divided into 4 compartments marked 1,2,A,C 1 Pre-wash detergent 2 Wash detergent A Softeners, conditioners, perfumes C Bleach
6
Caution: Turn off the power and turn the program...
User Manual - Page 11
...machine technician or a Haier designated service point for proper installation of the washing ...machine. Place the water inlet hose nut on the back of the water drainage hose .fix the water drainage hose support with waterproof sring.Do not use .
= Supplementary earth cable should be the same as an accessory for power cable replacement...
User Manual - Page 12
...washing machine should be adjusted, as shown in figure 3, so that it is level. Installation
As shown in figure1 remove all the packing materials (including the foam base).
= ...remove the three packing bolts from shock during transportation The steps below should be followed before using the appliance, 1.
Fig 3
4 Remove the rear panel of the washing machine,the rubber hose and then the...
User Manual - Page 13
... panel of the port hole.
9. unplug the washing machine and wipe clean the lower part of the washing machine.
4. After washing, turn off the tap to prevent leakage; Before washing, do up zippers, buttons ,laces and repair damaged areas,underwear or small articals should be placed in the laundry bag or a pillowslip...
User Manual - Page 14
... and direct sunlight to set washing program.
2 After turning the power off, turn the program knob clockwise to prevent plastic and rubber components from aging.
11. The washing machine must not be place in area of high moisture as water droplets may form on electrical components, Air dry the appliance if the washing...
User Manual - Page 15
... is required for 15A. Fuses in close vicinity to a washing machine technician or a Haier designated service point for power cable replacement.
4. Refer to the washing machine; Do not allow children play with the door during the heating process. After installation of the washing machine,the power plug should be accessible during the water heating...
User Manual - Page 16
For your safety, any instructions in this manual with this "Warning" sign shall be strictly followed.
This diagram may vary slightly with the layout of Parts
Detergent distributor Operation button Door Porthole
Top program knob Temperature knob
Power supply cable Earth terminal
Back plate screw (3) Drainage hose
Drainage hose clip Packing ...
User Manual - Page 17
Operation Manual
HA600TX
Automatic Drum Washing Machine
Table of Contents
Before using
Names of Parts inside front cover Matters Needing Attention 1-3 Installation 4-5 Control Panel 6 Operational Functions 6-7
During using
Program Selection 8 Preparation 9 Washing Methods 10-11
Maintenance
Maintenance 12 Trouble Shooting 13 Technical Specification 14 Wiring Circuit 15
Haier HA500TX Reviews
Do you have an experience with the Haier HA500TX that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Haier yet.
Earn 750 points for your review!