Haier H2SM-18HC03 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier H2SM-18HC03 manuals!
Problems with Haier H2SM-18HC03?
Ask a Question
Free Haier H2SM-18HC03 manuals!
Problems with Haier H2SM-18HC03?
Ask a Question
Popular Haier H2SM-18HC03 Manual Pages
User Manual - Page 1
No.0010555643 SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
H2SM-14HC03/R2 H2SM-18HC03/R2
Please read this operation manual before using the air conditioner.
User Manual - Page 2
...packaging materials employed in the User's Guide.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the package of your... put into smaller pieces and given to a waste paper disposal service.
Installation shall be done by professional people, don't install unit by insisting on an appropriate, anti-pollution method of disposal...
User Manual - Page 4
...Remote signal receiver
A beeping sound is generated when a signal from the one shown in the manual according to adjust up during compressor running in normal operation. Operation mode indicator
Lights up and ...down air flow. (Don't adjust it in cooling when room temp. Parts and Functions
Indoor Unit
Inlet grille
Air filter Vertical flap
Use remote controller to the product purchased...
User Manual - Page 5
Parts and Functions
The machine is adaptive in line with the appliance. 10.The appliance must be replaced by young children or infirm persons without supervision 9.Young...H2SM-18HC03/R2
Through poor conditions of a lamp). The appliance is attached inside the machine. 12. A breaker should be incorporated into fixed wiring. If the MAINS-IMPEDANCE Zmax If the fuse on strong enough supporter...
User Manual - Page 6
... time and after replacing batteries in remote controller, clock should be displayed on LCD. Each press will be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes.
Parts and Functions
Buttons and display of the code ,press code B can cause it will become normal.
5 FAN SPEED display
4. SLEEP display
6. CODE
Used to set correct time...
User Manual - Page 9
...replacing batteries, press ON/OFF, and display
explanation of the displayed
becomes as follows:
LO MED HI AUTO
Unit will run in selected mode. All indicators on LCD. Vertical flap closed automatically. Hints
Remote controller can memorize settings...mode.
(4) Unit stop
Press ON/OFF button. No
with the previous setting. Operation
Auto run, Fan operation
Enjoy yourself by just a gentle press....
User Manual - Page 10
...air will run intermittently at LO speed
regardless of time due to reach the temp.
setting, unit will run in operation mode displayed on LCD. Remote controller can memorize each ...start
Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on LCD.
(4) Fan speed selection
Press FAN button. For each operation status...
User Manual - Page 11
... About 60o
Up and down as well. Left and right air flow adjustment (manual)
Move the horizontal blade by a knob on cooling only unit. Hints
As cold...in HEAT mode, adjusting air flow downward will remove your health in summer to go out. So, you'd better set a temp.
Vertical flap closes automatically.
Be careful not to system protection. Press SWING button stop
Press ON/OFF ...
User Manual - Page 12
... operation mode. If button is pressed, time decreases 10 min. Hints
After replacing batteries or a power failure happens, Time setting should be displayed on indoor unit lights up. Operation mode will be shown ...will be reset.
Every time the button is kept depressed, time will flash.
(3)Timer setting
Press HOUR / button.
Every time the button is the same as follows:
ON
OFF...
User Manual - Page 13
... change TIMER mode.
Time displayed: Unit starts at X hour X min. AM refers to morning and PM to afternoon
(4) Time confirming for TIMER ON After time setting, press TIMER button to change quickly. It can be adjusted within 24 hours.
Every time the button is pressed, time increases 10 min. "ON" stops...
User Manual - Page 15
... your finger from the switch, the cooling operation starts with the air flow speed setting "Hi". Operation
Emergency and Test Operation
Emergency operation:
Use this operation only when the...
When the remote controller is a model for the removal, then the selected operation by the timer. In this operation, it is possible to change the
settings of this switch in the normal ...
User Manual - Page 16
...
decreases 2oC 1 hr
1 hr
decreases 2oC
Approx. 3 hrs
3 hrs
Rises 1oC
SLEEP mode starts
SLEEP mode stops
Fig.2
is not available.
15
Fig.1
Temp. setting
Unit stop
Power Failure Resume Function
If the unit is higher than temp. will run in Fig.l)
In HEAT mode
One hour after SLEEP mode ...
User Manual - Page 17
...of heavy stain, clean it upward.
3.Clean the filter Use a vacuum cleaner to the front. Maintenance
Different models have different appearance
Cleaning of unit casing Cleaning of remote controller
Cut off the detergent on unit casing completely.... the stopper so that it is completely behind the stopper, otherwise problems might occur.
16
Remove it by pulling it with soft cloth.
User Manual - Page 18
...the Air Purifying Filter
Replace old Air Purifying Filter with the machine.
NOTE: Please replace the Air Purifying Filter in 3-6 months as white side face to the upper installation methods. The air ...
6 Close the inlet Grille
Close the Grille surely.
Stuffed filter are using may cause trouble with new one at sales shop.
17
Air Filter
4 Attach the Air Purifying Filter
...
User Manual - Page 20
...too many people in the room during cooling operation? Is temperature set correctly? This is pulled out and reinserted, the protection circuit ... because of furniture, cigarettes.
Multiple check
Does not work for service, check the following first. Is there any obstacles before inlet...Application temp.
Trouble shooting
Before asking for 3 minutes to protect the air conditioner....
Haier H2SM-18HC03 Reviews
We have not received any reviews for Haier yet.