Haier AC162FEAHA Support and Manuals
Get Help and Manuals for this Haier item
This item is in your list!
View All Support Options Below
Free Haier AC162FEAHA manuals!
Problems with Haier AC162FEAHA?
Ask a Question
Free Haier AC162FEAHA manuals!
Problems with Haier AC162FEAHA?
Ask a Question
Popular Haier AC162FEAHA Manual Pages
User Manual - Page 2
.... Use special circuit of the assembly to the operation manual. Meanwhile, explain method of machine. Ask installation personnel to bear the weight of refrigerant. Improper grounding can cause fire hazard etc. Trial run MUST be done after finishing installation.
Safety Precautions
Read this installation instruction and operation manuals should be kept by the user. Warning! Warning...
User Manual - Page 3
... of metal parts of building and air conditioner should be carried on in the back)
>500mm
>20mm
Don't put any obstacles near
the wind inlet. Omission of the series are different)
>300mm
Machine (horicontal&front view)
>300mm
horicontal&side view) (Lower in compliance with technical standards of electrical appliances and facilities.
3.Installation place for space...
User Manual - Page 4
...242,282FEBHA. Installation of supporting frame for installaiton 4-12x27
Internal suspension
B
Space length between suspending bolts
Suspending bolt less than 40mm.
Installation position of ...wall
As shown in under ceiling
1. Install a guard ring and then seal it with its outside inclining lower slightly.
Installation of Air Conditioner
Installation in the diagram at the right, ...
User Manual - Page 5
... paste board of suspending bolts
Wood building
New concrete building
Install beam wood on the girder and set supporting angle iron
Hook bolt
Old concrete building Use inlet hinge joint, inlet plug or inlet bolt.
Installation of air conditioner
Bolt supporting frame
Bolt supporting frame
Insert hexagon bolt into carved fillet. Beam wood
girder
Suspending bolt
cultellate insert...
User Manual - Page 6
...an outlet direction for pipeline and wiring.
down
(3) Install supporting frame as shown in the diagram on the left and...
1.
Installation of (AC092,122,142,162FEAHA,AC092,122,142,162FEBHA)
(1) Fix four rubber footings, 4X16 screw snail, 12 washer on...
5
Indoor part of the machine
6.78cm 5.53cm 4.73cm 8.8cm
3.5cm hole
12.5cm
10cm
(4) Install drainage pipe Install drainage pipe...
User Manual - Page 7
... gas side of distribution tube
Please read installation manual attached with unit of outdoor unit.
Poor heat insulation can cause moisture condensation and result in water leakage
6
Air tightness test
Evacuation
Addition of refrigerant
Air tightness test, evacuation and addition of refrigerant should be powered on ).
Checkup of joint part of drainage pipe
(2) According to spot...
User Manual - Page 8
...refrigeration, temperatures in following diagram.
1.5m~2m Supporting ... tape Insection should be taken to indoor drainage pipe to joint part between drainage pipe and indoor assembly. Heat insulation measures should be... to prevent undulation.
Same measures also should be set to the two sides.
Drainage pipe is long, a supporting frame should be taken to prevent moisture condensation....
User Manual - Page 9
... by wires transferring to keep away from AC220-230V and AC380-400V. Notice
Install electrical leakage protector. Improper connection can cause electric shock. To prevent interference of electrical facilities.
Remote controller wire
Specification of power supply shall be replaced by the manufacturer or its two contacts should be no less 3mm.such means...
User Manual - Page 10
... group number are shown as following sequence:
(1)Set number setting switch SW01 on control base board of number 2-16 indoor
subassemblies to prevent wrong connection that of number 3 respectively
(according to installaiton manual of centralized controller
Operation control
Solution of group control
One set of indoor subassemblies
Code switch AW02 on SW02 or with length...
User Manual - Page 11
... should be changed in the following way to amend heating temperature.
Improve efficiency of horizontal orientation. Settings of heating temperature compensation (usage of switch SW03)
Enhance air circulation with supporting frame after finishing installation, dial code of valves in air conditioner room and drainage pipe after changing circuit board.
Relation between power supply and...
User Manual - Page 12
... is not a defect if trouble-shooting code ì95î is in ON status before trial run. 2.Compulsory trial run can make air conditioner run reluctantly but stop after finishing compulsory trial run of power supplies for operation sequence.
Trial run of cooling program
Set ìrunning modeî to manually operate AC contactor of cooling...
Haier AC162FEAHA Reviews
Do you have an experience with the Haier AC162FEAHA that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Haier yet.
Earn 750 points for your review!