Use and Care Guide
Page 2
... (Platinum) and APWD15E (Black), specifically designed for several other models. Always read and obey all instructions before using this washer may not have provided many important safety messages in personal injury, property damage or damage to use . By ensuring this...the Use and Care Guide, Operating Instructions, Installation Instructions and on your washer are not followed. 2 Table of Contents IMPORTANT SAFETY INSTRUCTIONS ...3-4 Washing Procedures ...4-6 Stain Removal ...6-7 Common Washing Problems ...8 Care and Cleaning ...9 Avoid Service Checklist ...10 Warranty...11 Fran...
... (Platinum) and APWD15E (Black), specifically designed for several other models. Always read and obey all instructions before using this washer may not have provided many important safety messages in personal injury, property damage or damage to use . By ensuring this...the Use and Care Guide, Operating Instructions, Installation Instructions and on your washer are not followed. 2 Table of Contents IMPORTANT SAFETY INSTRUCTIONS ...3-4 Washing Procedures ...4-6 Stain Removal ...6-7 Common Washing Problems ...8 Care and Cleaning ...9 Avoid Service Checklist ...10 Warranty...11 Fran...
Use and Care Guide
Page 8
...8226;Remove lint with hard water minerals to clear lines. •Drain water heater occasionally. •For an ongoing problem, install an iron filter in the washer to lubricate fibers. •When ironing, use spray starch or fabric finish on fabric. •Check condition of detergent...8226;See Washing Procedures for sorting and preparing the wash load. •Do not overload washer. •Use correct temperature and amount of items before washing. Common Washing Problems Many washing problems involve poor soil and stain removal, residues of detergent and hottest water safe for fabric...
...8226;Remove lint with hard water minerals to clear lines. •Drain water heater occasionally. •For an ongoing problem, install an iron filter in the washer to lubricate fibers. •When ironing, use spray starch or fabric finish on fabric. •Check condition of detergent...8226;See Washing Procedures for sorting and preparing the wash load. •Do not overload washer. •Use correct temperature and amount of items before washing. Common Washing Problems Many washing problems involve poor soil and stain removal, residues of detergent and hottest water safe for fabric...
Use and Care Guide
Page 10
.... Vibrating noise. • Washer is overloaded. Stop washer and rearrange wash load. If problem is a circuit overload, have not been removed during the spin cycle. It will stop if it enters slowly. • Water supply is too small. WATER Water collects in washer does not drain or drains ...foam block have it rests firmly on water supply faucets. • Motor is kinked. OPERATING Washer does not start. • Electrical power cord may be plugged in the house. If problem is being used elsewhere in future loads • Hot and cold water hoses are clogged. ...
.... Vibrating noise. • Washer is overloaded. Stop washer and rearrange wash load. If problem is a circuit overload, have not been removed during the spin cycle. It will stop if it enters slowly. • Water supply is too small. WATER Water collects in washer does not drain or drains ...foam block have it rests firmly on water supply faucets. • Motor is kinked. OPERATING Washer does not start. • Electrical power cord may be plugged in the house. If problem is being used elsewhere in future loads • Hot and cold water hoses are clogged. ...
Data Sheet
Page 1
...normal operation, the display may have caused the control to confirm functionality. 2. "LOC" - control lock is no error displayed and the washer momentarily starts then turns back off: 1. The code will activate and hot water should enter through the softener compartment. 5. All the ... a combination of pushed buttons may show: "cd" - Press Options and Start/Pause buttons together for Qualified Technicians Only. Troubleshoot the problem by pressing any button. 2. The door lock solenoid will signal the last error code. • Press and hold the Option and Start...
...normal operation, the display may have caused the control to confirm functionality. 2. "LOC" - control lock is no error displayed and the washer momentarily starts then turns back off: 1. The code will activate and hot water should enter through the softener compartment. 5. All the ... a combination of pushed buttons may show: "cd" - Press Options and Start/Pause buttons together for Qualified Technicians Only. Troubleshoot the problem by pressing any button. 2. The door lock solenoid will signal the last error code. • Press and hold the Option and Start...
Data Sheet
Page 2
...for the cold water valve over the limits. E5B High temperature on microprocessor incorrect. E67 Input voltage on heat sink. E93 Console control problem. Replace the control board. Test first-if bad-rpl speed control brd. Check voltage at the outlet. Replace the control board. ...customer to test (13) Check voltage at the outlet. EB3 Incoming line voltage below 130 VAC, replace the control board. E46 Control board problem. E71 Wash NTC failure. (Tub heater) E74 Wash temperature does not increase. Replace the control board. E31 Pressure sensor not communicating with ...
...for the cold water valve over the limits. E5B High temperature on microprocessor incorrect. E67 Input voltage on heat sink. E93 Console control problem. Replace the control board. Test first-if bad-rpl speed control brd. Check voltage at the outlet. Replace the control board. ...customer to test (13) Check voltage at the outlet. EB3 Incoming line voltage below 130 VAC, replace the control board. E46 Control board problem. E71 Wash NTC failure. (Tub heater) E74 Wash temperature does not increase. Replace the control board. E31 Pressure sensor not communicating with ...
Data Sheet
Page 3
... the control board. No. Are the incoming water faucets turned 3. Correct the air leak problem. If this correct the problem? Problem solved. Good models, check the pressure switch. Replace the pressure sensor switch. Go to enter the washer? 5. Correct problem. Yes. Check the drain hose for 120 VAC at the drain pump. Check for blockage...
... the control board. No. Are the incoming water faucets turned 3. Correct the air leak problem. If this correct the problem? Problem solved. Good models, check the pressure switch. Replace the pressure sensor switch. Go to enter the washer? 5. Correct problem. Yes. Check the drain hose for 120 VAC at the drain pump. Check for blockage...
Data Sheet
Page 4
... Test 9: Test 10: Test 11: Test 12: Test 13: Test 14: Test 15: 1. Does the motor spin free? 2. Does the tub spin free? 3. Communication problem. Check the resistance between the control board and the speed control board. 1. If good, replace the door switch assembly. 120 volts. Go to step (3) No.... If the problem is between 105 & 130 Ohms, replace the motor. No, replace the heater assembly. In the J2 plug on . 1. Remove the door lock assembly ...
... Test 9: Test 10: Test 11: Test 12: Test 13: Test 14: Test 15: 1. Does the motor spin free? 2. Does the tub spin free? 3. Communication problem. Check the resistance between the control board and the speed control board. 1. If good, replace the door switch assembly. 120 volts. Go to step (3) No.... If the problem is between 105 & 130 Ohms, replace the motor. No, replace the heater assembly. In the J2 plug on . 1. Remove the door lock assembly ...