Fluke 2271A-N-G2M/A100K Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 2271A-N-G2M/A100K manuals!
Problems with Fluke 2271A-N-G2M/A100K?
Ask a Question
Free Fluke 2271A-N-G2M/A100K manuals!
Problems with Fluke 2271A-N-G2M/A100K?
Ask a Question
Popular Fluke 2271A-N-G2M/A100K Manual Pages
Product Manual - Page 4
2271A
Operators Manual
Vent and Abort 29 Pressure Measurement 29 Rear-Panel Manifold Pressure Connections 29 SUPPLY Port 30 EXHAUST Port (Vacuum Pump if Required 30 VENT Port 31 Test Ports 31 HC20 32 Connect a UUT 34 Test Port Insert 36 REF Port 37 Pressure Control Settings 37 Control Modes 39 Dynamic Control Mode...
Product Manual - Page 13
...0.02 %
PM200-G2M
0 MPa to ...support...Fluke products online at a 95 % level of the Barometric Reference Module.
6
MyFlukeStore Shop for gauge mode modules assumes routine zeroing. This specification can be reduced to 0.05 % FS if the PM200 module is calculated as the uncertainty of the gauge mode module plus the uncertainty of confidence, k=2, normally distributed. 2271A
Operators Manual...
Product Manual - Page 22
...General Tasks section. When this manual in large amounts.
Indicates ...Fluke products online at this section of measure.
Shows the active measurement mode and when selected, opens a menu to set a target pressure.
See the Unit and Custom Units section. The Control Settings mode relies on each setting within stability limits.
Modes supported -
The Measurement Setup...
Product Manual - Page 25
...Setup Menu section for detailed information on each menu item. Diagnostic - A Pneumatic Self Test can be run pre-programmed functions (tasks). This menu has options and parameters for pressure control. See the General Tasks section for detailed information on each menu item. Tasks - See the Pressure Control Settings section for Fluke... 2271A
Operators Manual
The Setup ...
Product Manual - Page 27
... . When the Product is factory set the date for Fluke products online at any time over the remote interface use the CAL_PASSWD
command. The Product prompts for a new password. The password contains 1 to 8 digits and is connected to 2271. Once the password is entered, the Product is lost, contact Fluke Calibration Customer Service for the current...
Product Manual - Page 31
...with a full set the entry. Numbered keys to clear the value entry in any mode but if this button is entered with caps). For example, to enter the Setup Menu. As a...Push to increase. See the Vent and Abort section for Fluke products online at: www.
.com 1.888.610.7664 As the different UI
items are disabled. 2271A
Operators Manual
Item
Table 9. To enter...
Product Manual - Page 39
... install and service the CPS. HC20 The HC20 test port has an M20X1.5 female thread and an O-ring inside of set ...service.
Note Excessive leaks in the test volume affect control stability and possibly cause measurement errors in the test system.
2271A
Operators Manual... and instructions on an O-ring and thus do not require PTFE tape. The maximum acceptable leak rate for Fluke products ...
Product Manual - Page 45
... upper, lower, and vent limit can be manually set in the stability limit. Returns the parameters of the pressure step. See the Safety Limits section.
38
MyFlukeStore Shop for Static Control sections. 2271A
Operators Manual
1 2 3 4
5
Table 12.
The measurement indicator shows "Not Ready" until the pressure is stable within defined user limits. See the...
Product Manual - Page 49
... °C) inch of calibration requirements.
2271A
Operators Manual
Measurement Setup
The Measurement Setup menu contains all options and parameters related to on each setting within this screen, enter the necessary parameters... NASA TN D-822
per MIL-STD-859A per MIL-STD-859A
42
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 Abbreviation
MPa kPa hPa Pa mmH2OC...
Product Manual - Page 50
...PM200G400K). To prevent misinterpretation of PMMs are installed. Automated Pressure Calibrator
Measurement Setup
Measurement Modes
Note The measurement modes depend... are 0.1, 0.01, 0.001.
43
MyFlukeStore Shop for Fluke products online at the beginning of 0 represents a pressure ... Open the Measure Settings on the Product, look at atmospheric pressure. A value of the model number) can be...
Product Manual - Page 58
...setup values are:
Setpoint:
Change value when necessary
Set to ATM / Enter Value:
Set... point to save the new program name. Insert:
Insert a new test point above the selected point. The max time selection limits the amount of time that the Product can spend on any one step of the program. Push to atmosphere or enter value manually...MyFlukeStore Shop for Fluke products online at...
Product Manual - Page 92
...model number, serial number, and firmware revision. The Product then changes the control coefficients to provide the best control performance. Temperature - For manual testing and troubleshooting, select a single PMM and test the valve. See the Service Manual for Fluke... properly, an error with information is... Shop for replacement instructions. This is... isolation valve installed on the...
Product Manual - Page 95
....
No supply pressure
Provide supply pressure if not connected.
88
MyFlukeStore Shop for repair. Valves require service
Send the Product to Fluke Calibration for Fluke products online at: www.
.com 1.888.610.7664
No pressure supply
Apply proper supply pressure.
2271A
Operators Manual
Problem
Product will not enter control mode
No pressure measurement is shown
Product does...
Product Manual - Page 96
... not correct
Improper command syntax
Cables are the wrong type or not properly connected
Confirm setting in the Product
Remove shipping plugs or excessive restriction. Automated Pressure Calibrator
Troubleshooting
Problem Product does not control down
No remote communications
Problem
No electrical measurement is within the measurement range (0 mA to 24 mA, 0 V to controller with...
Product Manual - Page 99
User-Replaceable Parts and Accessories (cont.)
Description
Fluke Part Number
PM200-BG100K, PRESSURE MEASUREMENT MODULE PM200-A200K, ... W/O Adapters TST-20M Test Station, 20 MPa (3000 psi)
Contact Fluke Calibration
Total Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1
1 1
1
1
1 1
92
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 2271A
Operators Manual
Table 19.
Fluke 2271A-N-G2M/A100K Reviews
Do you have an experience with the Fluke 2271A-N-G2M/A100K that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!