Fender MA6 Support and Manuals
Fender MA6 Videos
Popular Fender MA6 Manual Pages
Owners Manual - Page 3
PHYSICAL DIMENSIONS (APPROXIMATE, FOR SHIPPING PURPOSES)
MIXER AMPLIFIER
SPEAKER COLUMN
U.S.
System
Metric System
Weight
50 Pounds
22.67 kg
62 Pounds...8226; 1300 EAST VALENCIA DRIVE • FULLERTON, CALIFORNIA 92634
NOTE: See accompanying limited warranty folder •
MA6
MIXER AMPLIFIER
OPERATION INSTRUCTION MANUAL
BY
d
MADE IN U.S.A.iSts°1.°
•
it141 zittl;id .
Owners Manual - Page 5
...11
7 SECTION III
7 7
6 Channel PA Speaker System 12 HF Speaker Enclosure System
13 ...Settings
9
5
Final Control Adjustments
9
5
Volume
9
5
Tone
9
5
Master Section Reverb Return and Effects
5
Return Switches
9
5
Emphasizing One Instrument on
5
the Monitor Speakers
9
5
Equalizers
9
5
Explanation of the Equalizer Controls
10
5 Mixer Use
10
5
Use of an Additional Mixer...
Owners Manual - Page 6
... Response Curves 9 Master Section Effects, Direct Inputs, Reverb Jacks
• 6
6
10 Rear Panel
7
11 Typical Stage Setup
8
12 Speaker Connections
8
13 Effects Jack Connections
10
15 Typical Speaker, Monitor, and Tape Recording Connections
11
16 MA6 System with Auxiliary and Monitor Speakers
11
17 Bi-Amp Connections
12
18 Tape Recording
12...
Owners Manual - Page 7
... power amplifier are contained in
one compact package, hereafter referred to as the
"Mixer." The remaining pages of this Manual detail the functions of a mixer with associated horn and crossover network mounted in a Thiele aligned vented enclosure. •
INTRODUCTION
The Fender MA6 is composed of the various controls and jacks (in total, the unit has...
Owners Manual - Page 8
...identical. Item 1)
This adjusts the gain of the microphone preamplifier, allowing adjustment of the Mixer to provide the optimum signal-to be turned down until the light just flickers, to that... be changed. Treble Control (Fig. 3 -
Item 6) is just flickering, the control is properly set , it will not need to -noise ratio for frequency response curves.
INPUT
LO2 INPUT
INPUT AMP
GAIN...
Owners Manual - Page 12
... for each channel.
NOTE: Only one time on and off in Section II under "MIXER USE." This jack allows use of the five controls is discussed in the Monitor (Mon... (5 Slide Controls) (Fig. 7 - While both inputs are active simultaneously, the gain balance for chaining additional mixers.
A high impedance (Hi-Z) phone jack is indicated in Figure 8.
VU Meter (Fig. 7 - Item 3)...
Owners Manual - Page 13
... mV rms.
REVERB FOOT SWITCH JACK (Fig. 9 - Receive (Fig. 9 - Master Section Effects, Direct Inputs, Reverb Jacks
It functions only if the front panel controls are set to the Effects Return control. The nominal input impedance for the Reverb Foot Switch which turns the reverb on or off. +10
AMPLITUDE IN dB...
Owners Manual - Page 14
...6)
Speaker Output (Fig. 10 - This fuse is present at this signal should be connected to the Mixer, disconnecting the internal reverb unit. Line Cord Receptacle (Fig. 10 - Circuit Breaker (Fig. 10 -...used for storage of the speaker systems to connect the output of the speakers should be replaced only with the speaker jacks. Total impedance of the external reverb unit to an external ...
Owners Manual - Page 15
... "zip" cord for speaker hookups will allow much higher volume levels before feedback occurs.
Typical Stage Setup
FROM SPEAKER 12) JACKS
os
P
E
A
MA6
A
K
MIXER
K. Low impedance microphones plug into the AC socket in the rear of the Mixer (Fig. 10 - AC Power Cord
Remove the 120 VAC power cord from the inside of the...
Owners Manual - Page 16
... the monitors. will probably need to have the Gain control set to feedback or ring. Line level devices, like tape recorders, will probably sound distorted. A singer may cause the red light to the "flat" (center) position.
4.
Item 6) to the right (clockwise). Equalizers
The MA6 has two 5-band graphic equalizers (Fig. 7 Item 1 and 2) one...
Owners Manual - Page 17
...the Effects Send and Receive jacks and may be used as an expander. MIXER USE
Use of an Additional Mixer (Fig. 13)
The Fender MA6 can also be used for tape recording. Item 4) and the Monitor ...in the effects loop. If they are used, they are required, this control a bit will sound muddy. Cutting this jack can be used for the Monitor speakers. Maximum shelf is usually connected...
Owners Manual - Page 18
... jack (Fig. 10 Item 4). Item 3) to the Input of less than 4 ohms. Replace the fuse only with an additional P.A. The fuse protects the amplifier from damage which should use... ohm load through a 5 amp fuse mounted on the rear panel. MA6 System with Auxiliary and Monitor Speakers •
P
A AKER
K
r
MONITOR OUT
MA6 MIXER
ECTS
A K R
POWER
AMP
ER
MONITOR SPEAKER
FIGURE 15 - amplifier ...
Owners Manual - Page 19
...
AMP IN"
LOW
ELECTRONIC CROSSOVER
SPEAKER (LOW)
HIGH
POWER AMP
PRE. AMP OUT
T
J
"MONITOR OUT"
POWER AMP
MONITOR SPEAKER
MAS MIXER
MONITOR SPEAKER
FIGURE 17 - Tape Recording Bi-Amp Connections
• **No S P
E A
K E
R
H
TAPE
RECORDER
• 110--..111
S
P
"SPEAKER"
E
K
"PRE AMP OUT"
MA6 MIXER
H
-MONITOR OUT"
POWER AMP
MONITOR SPEAKER
MONITOR SPEAKER
FIGURE 18 -
Owners Manual - Page 20
... of the two 14/ " phone jacks, connected in a Thiele aligned vented box enclosure and a compression driver mid and high frequency horn. •
SECTION III 6 CHANNEL PA SPEAKER SYSTEM
12 HF Speaker Enclosure System (Fig. 19)
The Fender MA6 Public Address System is 8 ohms. The two speaker systems connected in parallel will provide the desired...
Fender MA6 Reviews
Do you have an experience with the Fender MA6 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fender yet.
Earn 750 points for your review!