Installation Guide
Page 1
EMC Departmental Switch DS-16B2 Installation Guide P/N 014003075-A01 This document explains the power, cooling, weight, and rack placement requirements for mounting them in Figure 1. It also describes the kits available for the 16-port EMC departmental switch shown in EMC and non-EMC Racks and includes installation instructions as well. RKH/RKL 5 • Installing the DS-16B2 Rails 10 • Installing the DS-16B2 Switch 21 EMC Departmental Switch DS-16B Installation Guide 1 Device 16-port departmental switch Device Model DS-16B2...
EMC Departmental Switch DS-16B2 Installation Guide P/N 014003075-A01 This document explains the power, cooling, weight, and rack placement requirements for mounting them in Figure 1. It also describes the kits available for the 16-port EMC departmental switch shown in EMC and non-EMC Racks and includes installation instructions as well. RKH/RKL 5 • Installing the DS-16B2 Rails 10 • Installing the DS-16B2 Switch 21 EMC Departmental Switch DS-16B Installation Guide 1 Device 16-port departmental switch Device Model DS-16B2...
Installation Guide
Page 3
Device Power, Cooling, and Weight Information Device Power, Cooling, and Weight Information Device Power Requirements DS-16B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz Cooling Requirements (Heat Dissipation) 368.5 BTU/hr Maximum Weight 12.9 kg (28.5 lbs) Device Dimensions Device DS-16B2 switch DS-16B2 switch with rails Height 4.34 cm 1.0 U 4.44 cm Depth 1.71 in 61.00 cm 24.01 in 1.75 in 61.00 cm 24.01 in Width 42.86 cm 16.87 in 43.18 cm 17.00 in EMC Departmental Switch DS-16B2 Installation Guide 3
Device Power, Cooling, and Weight Information Device Power, Cooling, and Weight Information Device Power Requirements DS-16B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz Cooling Requirements (Heat Dissipation) 368.5 BTU/hr Maximum Weight 12.9 kg (28.5 lbs) Device Dimensions Device DS-16B2 switch DS-16B2 switch with rails Height 4.34 cm 1.0 U 4.44 cm Depth 1.71 in 61.00 cm 24.01 in 1.75 in 61.00 cm 24.01 in Width 42.86 cm 16.87 in 43.18 cm 17.00 in EMC Departmental Switch DS-16B2 Installation Guide 3
Installation Guide
Page 4
... located at the top of the DS-16B2 switch in pairs. Switches are removed for the switch and the switch power rating listed in the table on the location of the rack/cabinet in the rack/cabinet. Switch (1 U) Switch (1 U) Filler Panel (2 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) 39 U DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DPE (6.5 U) Figure 2 SPS (1 U) Front Sample Cabinet Installation 4 EMC Departmental Switch DS-16B2 Installation Guide Rear EMC2056 Device Placement Requirements Device...
... located at the top of the DS-16B2 switch in pairs. Switches are removed for the switch and the switch power rating listed in the table on the location of the rack/cabinet in the rack/cabinet. Switch (1 U) Switch (1 U) Filler Panel (2 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) 39 U DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DAE (3.5 U) DPE (6.5 U) Figure 2 SPS (1 U) Front Sample Cabinet Installation 4 EMC Departmental Switch DS-16B2 Installation Guide Rear EMC2056 Device Placement Requirements Device...
Installation Guide
Page 5
... straight 2 per switch 2 7.5-foot USA power cords, straight C13 to N5-15P straight (with the (use the ones appropriate for an illustration of these components. RKH/RKL) Switch Mounting Kit (DS16B2 - RKH/RKL) The switch mounting kit includes rails, bezel, and power cords as listed in the table below for your PDU) DS-16B2-RKL kit only) EMC Departmental Switch DS-16B2 Installation Guide 5 Switch Mounting Kit (DS16B2...
... straight 2 per switch 2 7.5-foot USA power cords, straight C13 to N5-15P straight (with the (use the ones appropriate for an illustration of these components. RKH/RKL) Switch Mounting Kit (DS16B2 - RKH/RKL) The switch mounting kit includes rails, bezel, and power cords as listed in the table below for your PDU) DS-16B2-RKL kit only) EMC Departmental Switch DS-16B2 Installation Guide 5 Switch Mounting Kit (DS16B2...
Installation Guide
Page 6
Bezel, and Power Cords Long Rear Rails Ac Power Cords EMC2042 6 EMC Departmental Switch DS-16B2 Installation Guide Switch Mounting Kit (DS16B2 - RKH/RKL) Switch Mounting Brackets Front Rails Bezel Short Rear Rails Bezel Supports Figure 3 Rails.
Bezel, and Power Cords Long Rear Rails Ac Power Cords EMC2042 6 EMC Departmental Switch DS-16B2 Installation Guide Switch Mounting Kit (DS16B2 - RKH/RKL) Switch Mounting Brackets Front Rails Bezel Short Rear Rails Bezel Supports Figure 3 Rails.
Installation Guide
Page 7
Only the long rails, used in the switch mounting kit. EMC Departmental Switch DS-16B2 Installation Guide 7 RKH/RKL) Screws, Nuts and Washers See the table below for the EMC CLARiiON® rack come pre-assembled, with the power cord in the rail. The rail assemblies for a detailed list of all the securing hardware that is included in third party racks/cabinets, must be assembled. Switch Mounting Kit (DS16B2 -
Only the long rails, used in the switch mounting kit. EMC Departmental Switch DS-16B2 Installation Guide 7 RKH/RKL) Screws, Nuts and Washers See the table below for the EMC CLARiiON® rack come pre-assembled, with the power cord in the rail. The rail assemblies for a detailed list of all the securing hardware that is included in third party racks/cabinets, must be assembled. Switch Mounting Kit (DS16B2 -
Installation Guide
Page 8
... bezel, to secure the bezel to the rail assembly. 2 per switch mounting bracket. Used to secure mounting brackets to the rails. 2 per bezel support, to secure the bezel support to the rail assembly. 8 EMC Departmental Switch DS-16B2 Installation Guide pan-head screw (Qty. 6) 3 per rail for DS-16B2 in round-hole channels. RKH/RKL) Component #10 flat washer (Qty. 6) M5 keps nut...
... bezel, to secure the bezel to the rail assembly. 2 per switch mounting bracket. Used to secure mounting brackets to the rails. 2 per bezel support, to secure the bezel support to the rail assembly. 8 EMC Departmental Switch DS-16B2 Installation Guide pan-head screw (Qty. 6) 3 per rail for DS-16B2 in round-hole channels. RKH/RKL) Component #10 flat washer (Qty. 6) M5 keps nut...
Installation Guide
Page 9
Switch Mounting Kit (DS16B2 - RKH/RKL) Tools Required for Installation You will need the following tools to complete the installation of the rails and switch(es). Tools Required: #1 Phillips Screwdriver 6-mm (1/4-in.) 8mm (5/16-in.) Nut Driver Nut Driver EMC2065 EMC Departmental Switch DS-16B2 Installation Guide 9
Switch Mounting Kit (DS16B2 - RKH/RKL) Tools Required for Installation You will need the following tools to complete the installation of the rails and switch(es). Tools Required: #1 Phillips Screwdriver 6-mm (1/4-in.) 8mm (5/16-in.) Nut Driver Nut Driver EMC2065 EMC Departmental Switch DS-16B2 Installation Guide 9
Installation Guide
Page 10
Installing the DS-16B2 Rails Installing the DS-16B2 Rails This section describes the installation procedures for Clarity Rear Figure 4 View of the rails installed in a 39 U Rack/Cabinet 10 EMC Departmental Switch DS-16B2 Installation Guide EMC2071 Front Rear Door Removed for the DS-16B2 rails. Figure 4 shows a view of the Rails Installed in a 39 U rack/cabinet.
Installing the DS-16B2 Rails Installing the DS-16B2 Rails This section describes the installation procedures for Clarity Rear Figure 4 View of the rails installed in a 39 U Rack/Cabinet 10 EMC Departmental Switch DS-16B2 Installation Guide EMC2071 Front Rear Door Removed for the DS-16B2 rails. Figure 4 shows a view of the Rails Installed in a 39 U rack/cabinet.
Installation Guide
Page 11
... cabinet Figure 5 EMC2059 DS-16B2 Short Rear Rails (for the EMC CLARiiON Rack) To the rear of the cabinet Figure 6 EMC2060 DS-16B2 Long Rear Rails (for your rail kit contains 2 different length rear rail mounts, be sure to use the rail length that is appropriate for third Party Racks/Cabinets) EMC Departmental Switch DS-16B2 Installation Guide 11 The long rails...
... cabinet Figure 5 EMC2059 DS-16B2 Short Rear Rails (for the EMC CLARiiON Rack) To the rear of the cabinet Figure 6 EMC2060 DS-16B2 Long Rear Rails (for your rail kit contains 2 different length rear rail mounts, be sure to use the rail length that is appropriate for third Party Racks/Cabinets) EMC Departmental Switch DS-16B2 Installation Guide 11 The long rails...
Installation Guide
Page 14
... is installed on a table. 2. Ac Power Cord Lip Rack Front/ Plug into Switch Front Rail Figure 10 Installing the ac Power Cord in a non-EMC rack/cabinet. 1. The length can be adjusted once the switch is a new installation in an EMC CLARiiON rack, the rails are installing the switch in the Front Rail Rack Rear/ Plug into PDU EMC2068 14 EMC Departmental Switch DS-16B2 Installation Guide Follow these rail assembly instructions...
... is installed on a table. 2. Ac Power Cord Lip Rack Front/ Plug into Switch Front Rail Figure 10 Installing the ac Power Cord in a non-EMC rack/cabinet. 1. The length can be adjusted once the switch is a new installation in an EMC CLARiiON rack, the rails are installing the switch in the Front Rail Rack Rear/ Plug into PDU EMC2068 14 EMC Departmental Switch DS-16B2 Installation Guide Follow these rail assembly instructions...
Installation Guide
Page 16
See Figure 12. Keps Nut Keps Nut Figure 12 Securing the Keps Nuts EMC2045 If the side skins are adjusted to fit between the channels in the rack/cabinet you will locate the switch. 6. Adjust the length of the rail to the correct length, tighten the keps nuts on the rack/cabinet, the keps nuts can be tightened after the rails have been installed. 16 EMC Departmental Switch DS-16B2 Installation Guide Once the rails are removed on the rail assembly. Determine where in the rack/cabinet. 7. Installing the DS-16B2 Rails 5.
See Figure 12. Keps Nut Keps Nut Figure 12 Securing the Keps Nuts EMC2045 If the side skins are adjusted to fit between the channels in the rack/cabinet you will locate the switch. 6. Adjust the length of the rail to the correct length, tighten the keps nuts on the rack/cabinet, the keps nuts can be tightened after the rails have been installed. 16 EMC Departmental Switch DS-16B2 Installation Guide Once the rails are removed on the rail assembly. Determine where in the rack/cabinet. 7. Installing the DS-16B2 Rails 5.
Installation Guide
Page 17
...for the screws; Position the #10 flat washer and ball stud in the rear inside of the rack/cabinet. 1. EMC Departmental Switch DS-16B2 Installation Guide 17 Secure the rail to a round-hole channel with the holes in the center hole, between the two M5 x 10-mm screws. See ...switch is used for the other rail. The top and bottom screw holes are used for the ball stud. 2. NOTE: The ball studs support the bezel. 4. the center screw hole is installed. Hand-tighten the ball stud. Installing the DS-16B2 Rails Round-Hole Channel Follow the steps below to install...
...for the screws; Position the #10 flat washer and ball stud in the rear inside of the rack/cabinet. 1. EMC Departmental Switch DS-16B2 Installation Guide 17 Secure the rail to a round-hole channel with the holes in the center hole, between the two M5 x 10-mm screws. See ...switch is used for the other rail. The top and bottom screw holes are used for the ball stud. 2. NOTE: The ball studs support the bezel. 4. the center screw hole is installed. Hand-tighten the ball stud. Installing the DS-16B2 Rails Round-Hole Channel Follow the steps below to install...
Installation Guide
Page 18
Rack Rear Rear M5 x 10-mm Pan Head Screw (8) Front Figure 13 Installing Rails in Round-Hole Channels EMC2046 18 EMC Departmental Switch DS-16B2 Installation Guide Rack Front Align the front rail flange to the inside of the channel. Installing the DS-16B2 Rails Align the rear rail flange to the inside of the channel.
Rack Rear Rear M5 x 10-mm Pan Head Screw (8) Front Figure 13 Installing Rails in Round-Hole Channels EMC2046 18 EMC Departmental Switch DS-16B2 Installation Guide Rack Front Align the front rail flange to the inside of the channel. Installing the DS-16B2 Rails Align the rear rail flange to the inside of the channel.
Installation Guide
Page 19
...square-hole channel with 2 square-hole washers and M5 x 16-mm flat head screws (see table on page 8). EMC Departmental Switch DS-16B2 Installation Guide 19 The top and bottom screw holes are used for the other rail. Leave the screws finger-tight, and tighten them after the switch is installed. 5. ...flange of the rack/cabinet. 1. See Figure 14. 2. Align the holes of the front rail flange to install the rails assembly in the square-hole channel of the rail with 2 square- Installing the DS-16B2 Rails Square-Hole Channel Follow the steps below to the inside channel, as shown in...
...square-hole channel with 2 square-hole washers and M5 x 16-mm flat head screws (see table on page 8). EMC Departmental Switch DS-16B2 Installation Guide 19 The top and bottom screw holes are used for the other rail. Leave the screws finger-tight, and tighten them after the switch is installed. 5. ...flange of the rack/cabinet. 1. See Figure 14. 2. Align the holes of the front rail flange to install the rails assembly in the square-hole channel of the rail with 2 square- Installing the DS-16B2 Rails Square-Hole Channel Follow the steps below to the inside channel, as shown in...
Installation Guide
Page 20
M5 x 16-mm flat head screw (Qty. 8) Rack Rear Align the rear rail flange to the inside of the channel. Square-Hole Washer (Qty. 8) Figure 14 Installing Rails in Square-Hole Channels EMC2047 20 EMC Departmental Switch DS-16B2 Installation Guide Installing the DS-16B2 Rails Rack Front Align the front rail flange to the inside of the channel.
M5 x 16-mm flat head screw (Qty. 8) Rack Rear Align the rear rail flange to the inside of the channel. Square-Hole Washer (Qty. 8) Figure 14 Installing Rails in Square-Hole Channels EMC2047 20 EMC Departmental Switch DS-16B2 Installation Guide Installing the DS-16B2 Rails Rack Front Align the front rail flange to the inside of the channel.
Installation Guide
Page 21
... the Switch Mounting Brackets Switch Mounting Bracket EMC2048 EMC Departmental Switch DS-16B2 Installation Guide 21 Secure the bracket with the three screw holes on page 8). Installing the DS-16B2 Switch Installing the DS-16B2 Switch This section describes the procedures for installing the DS-16B2 switch in a rack/cabinet, including attaching the brackets on the rails. Tighten the screws fully. #8-32 x 5/16-in. The mounting brackets slide into the "C" channel...
... the Switch Mounting Brackets Switch Mounting Bracket EMC2048 EMC Departmental Switch DS-16B2 Installation Guide 21 Secure the bracket with the three screw holes on page 8). Installing the DS-16B2 Switch Installing the DS-16B2 Switch This section describes the procedures for installing the DS-16B2 switch in a rack/cabinet, including attaching the brackets on the rails. Tighten the screws fully. #8-32 x 5/16-in. The mounting brackets slide into the "C" channel...
Installation Guide
Page 22
... the "C" channel on each fixed rail. 3. Push the switch into the rack/cabinet until the hole in the front part of the Switch 4. Installing the Switch in the Rack/Cabinet Follow the steps below to the front of the switch. Place the ac power cords on top of the switch with the hole on the fixed rail. 22 EMC Departmental Switch DS-16B2 Installation Guide Align...
... the "C" channel on each fixed rail. 3. Push the switch into the rack/cabinet until the hole in the front part of the Switch 4. Installing the Switch in the Rack/Cabinet Follow the steps below to the front of the switch. Place the ac power cords on top of the switch with the hole on the fixed rail. 22 EMC Departmental Switch DS-16B2 Installation Guide Align...
Installation Guide
Page 25
Plug the power cords into the channels in the ac Power Cords EMC2053 EMC Departmental Switch DS-16B2 Installation Guide 25 Slide the excess cable back into the outlets at the back of the switch. Installing the DS-16B2 Switch 9. Secure the bezel support with two M3 x 8-mm pan head screws (see table on page 8). Bezel Support M3 x 8-mm Pan Head Screw (2 Per Bezel Support) Bezel Support EMC2052 Figure 19 Installing the Bezel Supports 10. See Figure 20. Figure 20 Plugging in the rails.
Plug the power cords into the channels in the ac Power Cords EMC2053 EMC Departmental Switch DS-16B2 Installation Guide 25 Slide the excess cable back into the outlets at the back of the switch. Installing the DS-16B2 Switch 9. Secure the bezel support with two M3 x 8-mm pan head screws (see table on page 8). Bezel Support M3 x 8-mm Pan Head Screw (2 Per Bezel Support) Bezel Support EMC2052 Figure 19 Installing the Bezel Supports 10. See Figure 20. Figure 20 Plugging in the rails.
Installation Guide
Page 27
... the fibre-optic cables to the switch and run the cables from the switch to the rack/cabinet. optic cable has a minimum bend radius of the ac cords into place, as shown in Figure 22. Plug the other end of 2 inches. 15. Secure the cables with the bezel supports and the ball studs. EMC Departmental Switch DS-16B2 Installation Guide 27 Ensure each fibre- Installing the DS-16B2 Switch...
... the fibre-optic cables to the switch and run the cables from the switch to the rack/cabinet. optic cable has a minimum bend radius of the ac cords into place, as shown in Figure 22. Plug the other end of 2 inches. 15. Secure the cables with the bezel supports and the ball studs. EMC Departmental Switch DS-16B2 Installation Guide 27 Ensure each fibre- Installing the DS-16B2 Switch...