Instruction Manual
Page 15
... conditions, such as these contain a rust inhibitor and an anit-foaming agent. Refer to the pump. 2. If the pressure washer is drained, replace oil drain plug. Remove pump oil plug and fill with oil at the factory. Always disconnect, spark plug wire, let the engine cool and ...in the OFF position. English NOTICE: Risk of property damage. Place the engine ON/OFF switch (H) to hot surfaces, water pressure or moving parts that can cause serious injury or death. Never turn water supply off . 5. Turn water source off while pressure washer engine is recommended as high...
... conditions, such as these contain a rust inhibitor and an anit-foaming agent. Refer to the pump. 2. If the pressure washer is drained, replace oil drain plug. Remove pump oil plug and fill with oil at the factory. Always disconnect, spark plug wire, let the engine cool and ...in the OFF position. English NOTICE: Risk of property damage. Place the engine ON/OFF switch (H) to hot surfaces, water pressure or moving parts that can cause serious injury or death. Never turn water supply off . 5. Turn water source off while pressure washer engine is recommended as high...
Instruction Manual
Page 17
...Avoid placing hands between handle and frame when assembling to or higher than what was provided with this pressure washer, do not use identical replacement parts. 17 danger: Risk of pump. 7. WARNING: The use of any accessory for use with this pressure washer as measured from your ...that is protected from water inlet of fluid injection. Store chemical hose so it in locating any other qualified service personnel. When using replacement lances or guns with this tool could be performed by a FNA factory service center, a FNA authorized service center or other accessory not...
...Avoid placing hands between handle and frame when assembling to or higher than what was provided with this pressure washer, do not use identical replacement parts. 17 danger: Risk of pump. 7. WARNING: The use of any accessory for use with this pressure washer as measured from your ...that is protected from water inlet of fluid injection. Store chemical hose so it in locating any other qualified service personnel. When using replacement lances or guns with this tool could be performed by a FNA factory service center, a FNA authorized service center or other accessory not...
Instruction Manual
Page 18
...forth in material and workmanship) Two (2) years from the manufacturer or alterations performed by this product agrees to repair or replace designated parts that prove defective within the warranty period listed below at the manufacturer's sole discretion. These warranties pass through to normal ...8226; Freeze damage • Damage caused by parts or accessories not obtained from date of defective products as provided herein and the manufacturer shall not be retained and available for return upon request to repair and replacement of purchase. Frame (defects in material and ...
...forth in material and workmanship) Two (2) years from the manufacturer or alterations performed by this product agrees to repair or replace designated parts that prove defective within the warranty period listed below at the manufacturer's sole discretion. These warranties pass through to normal ...8226; Freeze damage • Damage caused by parts or accessories not obtained from date of defective products as provided herein and the manufacturer shall not be retained and available for return upon request to repair and replacement of purchase. Frame (defects in material and ...
Instruction Manual
Page 21
.... Water supply must be the same consistency as water. Have parts cleaned or replaced by authorized service center. 21 English Have replaced by authorized service center. Have replaced by an authorized service center. Check and replace. When there is fully submerged into cleaning solution. Reconn... choke to rem ove remaining air. Tighten. Leak at least 5 GPM @ 20 psi (138 kPa). Have replaced by authorized service center. (Troubleshooting Codes cont.) Code 8 9 10 11 12 13 14 possible cause Fuel valve closed. Low water supply. Turn...
.... Water supply must be the same consistency as water. Have parts cleaned or replaced by authorized service center. 21 English Have replaced by authorized service center. Have replaced by an authorized service center. Check and replace. When there is fully submerged into cleaning solution. Reconn... choke to rem ove remaining air. Tighten. Leak at least 5 GPM @ 20 psi (138 kPa). Have replaced by authorized service center. (Troubleshooting Codes cont.) Code 8 9 10 11 12 13 14 possible cause Fuel valve closed. Low water supply. Turn...