Dewalt DXCMWA5591056 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DXCMWA5591056 manuals!
Problems with Dewalt DXCMWA5591056?
Ask a Question
Free Dewalt DXCMWA5591056 manuals!
Problems with Dewalt DXCMWA5591056?
Ask a Question
Popular Dewalt DXCMWA5591056 Manual Pages
Instruction Manual - Page 3
... levels of carbon monoxide can kill you cannot see or smell. Please read the manual and pay attention to personal injury which , if not avoided, may be breathing CO..., crawlspaces, or other partly enclosed areas. CAUTION: Indicates a potentially hazardous situation which , if not avoided, may result in death or serious injury. Idle RPM 1250-1600
Specifications
MODEL WEIGHT HEIGHT WIDTH LENGTH...
Instruction Manual - Page 4
...Code, unless the engine is used correctly, CO may leak into your home. See a doctor. WARNING: Do not operate this instruction manual and the engine instruction manual... arrester must be installed and is legally required...Service land and may not be equipped with a spark arrester, as the muffler.
• Shut off eng ine and allow for safety, operation and maintenance instructions...
Instruction Manual - Page 6
... the inner wall of injury to repair a damaged or leaking air tank.
Replace with a new air tank.
• The air tank is dependent upon several factors, some of maintenance.
Tank life is designed to withstand specific operating pressures.
Consumer Product
components which include operating conditions, ambient conditions, proper installations, field modifications, and the level...
Instruction Manual - Page 12
... correct procedure.
INSTALLATION
Assembly (Fig. 1)
INSTALLING HOSES WARNING: Risk of sparks (such as ...service center. English
valve vents air, it will automatically shut down the engine and will not start until oil is below minimum. This gas saving feature holds the engine at a factory-set idling speed until oil is equipped with recommended oil, see engine's instruction manual...
Instruction Manual - Page 13
...the air compressor, do
not provide adequate clearance, stability or support for pulling
the unit up a ramp. Contact a DeWALT service center or call 1-888-895-4549 for assistance.
WARNING: ... Consult local officials for information regarding acceptable noise
levels in the oil, causing running parts to the unit or surrounding items if unit
is tipped.
If you suspect that ...
Instruction Manual - Page 14
.... Check engine's oil and fuel level, see engine's instruction manual for Use.
2. Ensure all items have been verified. Initial Set-up (Fig. 1)
WARNING: Do not operate this unit...is closed. 4. stand the engine instruction's manual for the first time.
• When the unloader valve has been replaced.
• When the compressor pump has been replaced. Grasp handle (W) of compressor to ...
Instruction Manual - Page 16
...Operating Instructions). 8.
WARNING: Risk of unsafe operation.
Rotate the handle (X) up to desired setting....push down on the H4X remote hub (Z). 4.
English
troubleshooting section. Do not use damaged or
worn accessories. Some... release it is recommended to lock in hand when installing or disconnecting to the desired settings. 7. Remove air hoses.
9. Attach hose and...
Instruction Manual - Page 17
...locations of in this section should be disposed of parts during disassembly to form.
17 NOTE: Any service operations not included in accordance with local, state, ...
X
Check for air leaks
X*
Clean compressor exterior
X
Remove tank from service
X++
Engine
See engine instruction manual.
* To check for air bubbles to make reassembly easier. Ensure regulated pressure...replaced.
Instruction Manual - Page 21
... or service of the belt (AI) and
the straightedge at points A1 and A2 in Figure. Reconnect spark plug wire. Allow the unit to overwork, resulting in this manual is
perpendicular to verify that it is...173;ments should be equal.
lbs. (16.4 - 20.3 Nm).
10. Retighten the engine drive pulley setscrew. Reinstall belt guard. 13. Torque to be no more than 1/16" (1.6 mm), loosen the...
Instruction Manual - Page 22
... for use with this tool could be performed by a DeWALT factory service center, a DeWALT authorized service center or other air compressor components. Use only accessories rated equal to accessories or damage caused where repairs have the following information available for use identical replacement parts. Service Information
Please have been made or attempted by and identified as...
Instruction Manual - Page 23
... compressor, will render this warranty null and void. Parts used in the owner's manual, will render this warranty. Modifications to the product, or tampering with components, or failure to install, maintain, and operate said equipment in accordance with the specific recommendations of the Company set forth in repair of whole goods or accessories are as follows...
Instruction Manual - Page 24
...of air delivery.
California Code: Unit may comply with California Code. Unloader Blow-Off Pressure: All models are installed.
All associated freight costs...and allows it reaches the unloader blow-off . Specification/model label is obtained, the unloader valve will now...Service Center.
PSI: Pounds per square inch;
English
• All other parts 30 days
• ...
Instruction Manual - Page 26
..., clean or replace. English
CODE 1 2 3
4
5 6 7 8
9 10 11 12
Troubleshooting Codes
POSSIBLE CAUSE
POSSIBLE SOLUTION
Unloader valve does not release pressure when Unloader valve must be heard escaping. Contact a DeWALT factory
air tank reaches blow-off engine, rotate manual lock unloader lever to the closed perpendicular position. Leaking seals
Contact a DeWALT factory service center or...
Instruction Manual - Page 27
...service center.
Contact a DeWALT factory service center or a DeWALT authorized service center.
27
English Excessive vibration could weaken the air tank and cause it to tight
20
Pulley misalignment
21
Air tank pressure is too high
22
Engine problem....‑lbs. (13.5-27.1 Nm). CODE POSSIBLE CAUSE
13
Loose belt
14
Engine ...set screw, torque to 145-180 in pump
19
Belt to rupture or...
Instruction Manual - Page 28
...CODE POSSIBLE CAUSE
23
Engine or pump oil is low
24
It is normal for some pressure drop to occur
25
Damaged regulator
26
Detergent type oil being used. NOTE: Adjust the regulated pressure under flow conditions while accessory is being used , adjust the regulator as instructed in place.
Replace.
Contact a DeWALT factory service...Water in pump oil
32
Manual lock unloader lever in to...
Dewalt DXCMWA5591056 Reviews
We have not received any reviews for Dewalt yet.