Dewalt DXCMV5048055 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DXCMV5048055 manuals!
Problems with Dewalt DXCMV5048055?
Ask a Question
Free Dewalt DXCMV5048055 manuals!
Problems with Dewalt DXCMV5048055?
Ask a Question
Dewalt DXCMV5048055 Videos
DeWalt 80 Gallon 2 Stage Air Compressor Review DXCMV5048055
Duration: 4:08
Total Views: 31,383
Duration: 4:08
Total Views: 31,383
DeWalt DXCMV5048055 Two-Stage Cast Iron Industrial Air Compressor, 80-Gallon 175psi
Duration: :16
Total Views: 1,614
Duration: :16
Total Views: 1,614
Popular Dewalt DXCMV5048055 Manual Pages
Instruction Manual - Page 5
...which include operating conditions, ambient conditions, proper installations, field modifications, and the level of the... properly drain condensed water from service by the end of the ...specific operating pressures. Replace with a new air tank or replace the entire compressor.
• Modifications or attempted repairs to the air tank.
• Never drill into, weld or make adjustments or parts...
Instruction Manual - Page 8
...parts or attempting to repair compressor with guards or covers which are damaged or removed.
• Keep your clothing.
• Never operate the compressor with protective shrouds removed can expose you to you or others.
• Review and understand all instructions and warnings in this manual...broken, or una utho rized parts.
• Never stand on this produ ct.
...
Instruction Manual - Page 9
...the motor when the air tank pressure reaches the factory set cut -out pressure. CHECK VALVE When the air compressor ...end of each use , noise from others before removing or replacing B pressure switch cover.
Save this switch (B) in any ...(G) is in pressure.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Know Your Air Compressor
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR ...
Instruction Manual - Page 11
...8226; air compressor • operator and parts manuals
Check the compressor's serial label to ensure...outlet (F). If you have received the model ordered, and that will interfere with...INSTALLING HOSES WARNING: Risk of unsafe operation. Remove hose from your local dealer or authorized service... DISCONNECTING HOSES WARNING: Risk of unsafe operation. Set the Auto/Off switch to cool. 3. Allow...
Instruction Manual - Page 13
... the line from air pressure. Regardless of unsafe operation. NOTE: Compressed air from hot surfaces such as the motor. Grounding Instructions
This product should have the same electrical characteristics (voltage, cycle, phase) as manifold assembly, compressor outlet tubes, heads, or cylinders.
English
Refer to the Specifications, in the parts manual, for air distribution lines.
Instruction Manual - Page 15
...instructions are secure at less than 135 psi. Make sure all terminals
connections. After 30 minutes, turn counterclockwise to set
the outlet pressure to "cut-out" pressure and the motor will start. 6. The compressor is in period. 5. NOTE: A regulator MUST be installed...is put into service and when the check valve or a complete compressor pump has been replaced. 1. Move the...
Instruction Manual - Page 16
...using regulator and other accessories refer to the manufacturers instructions. Remove hose and accessory. Drain the air tank...tered air at an item that could be damaged by a trained service technician. How to
build.
Allow the compressor to lock in ...-out" pressure. 2. Firmly grasp air hose in hand
when installing or disconnecting to the OFF position. If not drained, water ...
Instruction Manual - Page 17
...does not operate smoothly, it must be replaced with side shields. Compressor outfits in ...air pressure. Tubes, pump head, and surrounding parts are very hot, do not touch (see...NOTE: See Operation section for air bubbles to servicing. If the safety valve does not work properly... or an explosion. Before performing any maintenance or repair, disconnect power source from flying objects.Always wear...
Instruction Manual - Page 18
... of burn. Keep face and other body parts away from noise. Remove the air tool ... (P) if it .
6. Secure with paint, replace
it is in Fig. 2).
Release safety valve ...the air tank causing a risk of drain. Allow unit to servicing. Remove the wing nut (N). NO P
4. Do not ...Set the Auto/Off switch to zero. 3. Pull the regulator knob out and turn counterclockwise to set...
Instruction Manual - Page 19
... pressure from the system before removing the oil fill cap or oil drain plug.
1. Set the Auto/Off lever to "Off", shut off the main power disconnect, and bleed ... parts are very hot, do not touch (see the Hot Surfaces identified in use the unit with moving parts. Replace oil fill plug (Q) and tighten securely. Changing
WARNING: Drain tank to be to servicing.
1.
Replace the...
Instruction Manual - Page 21
...voltage sources, compressed air, or moving parts. Unit cycles automati-
When servicing, you may be exposed to 14-... equal. Service and Adjustments
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.... B2, using a 7/8" open
valve. To Replace or Clean Check Valve
1. Release all air ...properly torqued. Set the Auto/Off lever to "Off", shut...
Instruction Manual - Page 22
...service calls: Model Number Serial Number Date and Place of purchase.
2 Year - English
valve (turn clockwise). 9. Perform the Break-in
the Operation section. Use only accessories rated equal to or higher than the rating of incidental or consequential damages, so the above limitations may not apply to materials
22 DEWALT will repair or replace...identical replacement parts. IMPLIED...manual...
Instruction Manual - Page 23
.... What is equipped with a gas engine, see engine manual for parts purchased separately such as: pumps, motors, etc., are warranted for labor performed by the original retail purchaser to install, maintain, and operate said equipment in accordance with the specific recommendations of the Company set forth in repair of ownership on stationary compressors (compressors without the...
Instruction Manual - Page 26
... CAUSE Fittings are not tight
Troubleshooting Codes
POSSIBLE SOLUTION
Tighten fittings where air can rupture or explode. Check fittings with soapy water solution. Do not repair the leak. Leaking seals
Contact a DeWALT factory service center or a DeWALT authorized service center. Compressor is needed to 85-90 in air hose
Check and replace air hose, if required...
Instruction Manual - Page 29
... per minute; Cut-in pressure: Factory set high pressure point that starts the compressor to repressurize the tank to a higher pressure. ASME: American Society of the air tank on the side of Mechanical Engineers. standard 1450. California Code: Unit may comply with California Code.
29
NOTES
English Specification/model label is on units that have...
Dewalt DXCMV5048055 Reviews
We have not received any reviews for Dewalt yet.