Dewalt DXCMV5018055 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DXCMV5018055 manuals!
Problems with Dewalt DXCMV5018055?
Ask a Question
Free Dewalt DXCMV5018055 manuals!
Problems with Dewalt DXCMV5018055?
Ask a Question
Popular Dewalt DXCMV5018055 Manual Pages
Instruction Manual - Page 5
..., proper installations, field ...repairs to the air tank.
• Never drill into, weld or make adjustments or parts substitutions to the air tank or its attachments.
If air tank develops a leak, replace it immediately with a new air tank.
• Unauthorized modifications to the safety valve, or any modifications to alter the factory set... to withstand specific operating pressures....
Instruction Manual - Page 8
... all instructions and warnings in serious injury.
• Any repairs required on the compressor. Loose clothes, jewelry or long hair can be caught in moving parts.
• Air vents may cover moving parts and ... te machine with missing, broken, or una utho rized parts.
• Never stand on this manual.
• Become into contact with the oper a...
Instruction Manual - Page 9
... below the factory set cut -in the OFF (O) position before lifting. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Know Your Air Compressor
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE..., allowing compressed
air to prevent system
failures by relieving pressure from others before removing or replacing pressure switch cover.
The valve is designed to enter the air tank.
SAFETY VALVE
This...
Instruction Manual - Page 10
... model ordered, and that are time limitations to damage claims.
The carton should contain: • air compressor • operator and parts manuals
Check... tank and is designed to remain inside the air tank.
Set the Auto/Off switch to AUTO (-).
MAGNETIC STARTER RESET SWITCH...Code. K
INSTALLATION
Assembly (Fig. 1)
Unpack the air compressor. See Air Distribution System paragraph under...
Instruction Manual - Page 11
...flow to the air compressor. Remove hose from forming in the oil, causing running parts to wear out prematurely.
You may form in the pump and produce sludge in ...milky" appearance in hand
when installing or disconnecting to prevent hose whip. 1. Location
• Locate the air compressor in your local dealer or authorized service center. INSTALLING HOSES WARNING: Risk of electrical...
Instruction Manual - Page 14
...Make sure the Auto/Off switch is put into service and when the check valve or a complete compressor pump has been replaced. 1. Open the drain valve (counterclockwise) fully ...Service. 7. ALWAYS USE METAL PIPING AND FITTINGS.
Readjust or shim air compressor feet, if necessary.
14 Correct if necessary. Before Starting
WARNING: Do not operate this unit until you read this instruction
manual...
Instruction Manual - Page 17
... pressure air.
Set the Auto/Off switch to servicing.
Allow compressor ...to cool prior to "Off". 2. Before starting compressor, pull the ring on the safety valve to bleed from the tank until
tank pressure is
dirty or filled with paint, replace
it must be replaced.... Tubes, pump head, and surrounding parts are very hot, do not touch ...
Instruction Manual - Page 19
...the engine pulley has been moved from its factory set location, the grooves of the belt and the ...See the Adjusting Belt Tension before tightening motor
mounting screws. Torque to servicing.
1. Verify the alignment by removing
the screws (R) using a
Torx...parts. Allow compressor to cool prior to 20-25 ft-lbs (27.1-33.9 Nm). Remove the front of burn. Remove the belt and replace...
Instruction Manual - Page 20
...Visually inspect the motor drive pulley to voltage sources, compressed air, or moving parts. To Replace or Clean Check Valve
1. wrench loosen pres- Unscrew the check valve (turn ... Service and Adjustments
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.
Unit cycles automatically when power is greater than 1/16" (1.6 mm) loosen the set ...
Instruction Manual - Page 21
...Replace the outlet tube and tighten nuts. 11.
WARNING: The use of any accessory for all service calls: Model Number Serial Number Date and Place of Purchase
Repairs
To assure product SAFETY and RELIABILITY, repairs... www.dewalt.com. Service Information
Please have the following information available for your tool are available for use identical replacement parts.
21 English
6. ...
Instruction Manual - Page 22
...manual, will cover parts
and labor to remedy substantial defects due to materials and workmanship during the first year of incidental or consequential damages, so the above limitations may not apply to faulty materials or workmanship. The Company shall not be liable for any repairs, replacements...specific recommendations of the Company set forth in repair... not apply to install, maintain, and...
Instruction Manual - Page 23
... caused by incorrect voltage, improperly wired, or failure to the nearest Authorized Service Center. Portable compressors or components must be delivered, or shipped, to have a certified licensed electrician install the compressor, will be borne by failure to be eligible for parts purchased separately such as: pumps, motors, etc., are as follows:
From Date...
Instruction Manual - Page 25
...
CODE POSSIBLE CAUSE
1
Fittings are not tight
2
Defective air tank
3
Leaking seals
4
Defective safety valve
5
Prolonged excessive use of air
Troubleshooting Codes
...manually by pulling on ring. Contact a DeWALT factory service center or a DeWALT authorized service center. WARNING: Risk of air usage.
25 Decrease amount of bursting. Do not repair the leak. The air tank can be replaced...
Instruction Manual - Page 26
...set screw, torque to 85-90 in pump
18
Extremely light duty cycles
19
Piston rings damaged or worn
POSSIBLE SOLUTION
Check the accessory air requirement. See Motor Pulley/Flywheel Alignment under Maintenance. See Compressor Pump Oil under Maintenance. Contact a DeWALT factory service center or a DeWALT authorized service center.
26 English
CODE... Nm). Clean or replace air intake filter.
...
Instruction Manual - Page 28
... Cubic feet per square inch; Specification/model label is on the side of providing fresh air in pressure: Factory set by CSA. Cut-out pressure: Factory set by ASME. Cut-in exchange ...for the exclusive use of air delivery. standard 1450. California Code: Unit may comply with California Code.
28...
Dewalt DXCMV5018055 Reviews
We have not received any reviews for Dewalt yet.