Dewalt DXCMH9919910 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DXCMH9919910 manuals!
Problems with Dewalt DXCMH9919910?
Ask a Question
Free Dewalt DXCMH9919910 manuals!
Problems with Dewalt DXCMH9919910?
Ask a Question
Popular Dewalt DXCMH9919910 Manual Pages
Instruction Manual - Page 5
...conditions, proper installations, field ...Replace with a new air tank or replace the entire compressor.
• Modifications or attempted repairs to the air tank.
• Never drill into, weld or make adjustments or parts...specific operating pressures. Add air in a violent air tank explosion:
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Failure to properly drain condensed water from service...
Instruction Manual - Page 8
...DeWALT factory service center or a DeWALT authorized service center.
8 Loose clothes, jewelry or long hair can be caught in moving parts.
• Air vents may cover moving parts. English
...parts.
• Never stand on this manual.
• Become into contact with you or others.
• Review and understand all instructions and warnings in serious injury.
• Any repairs...
Instruction Manual - Page 9
... (O) SWITCH
Place this manual for future reference. When the air compressor
9 SAVE THESE INSTRUCTIONS FOR FUTURE USE
Know Your Air Compressor
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING...before removing or replacing
pressure switch cover.
PRESSURE SWITCH
The pressure switch (B) automatically starts the motor when the air tank pressure drops below the factory set cut -in ...
Instruction Manual - Page 10
...-15 minutes
so the motor can be free from compressor.
INSTALLATION
Assembly (Fig. 1)
Unpack the air compressor. C
MAGNETIC STARTER
NOTE: These units require a magnetic
starter. Size the
wires, protect them with conduit, and provide branch circuit
protection per the National Electrical Code. Set the Auto/Off switch to AUTO (-). Depress the reset button...
Instruction Manual - Page 11
... and produce sludge in the oil, causing running parts to prevent moisture from forming in compressor oil. ...line filter for information regarding acceptable noise levels in hand
when installing or disconnecting to hose threads. 3. To reduce excessive noise... 1. Firmly grasp hose in your local dealer or authorized service center. If you suspect that is required. NOISE CONSIDERATIONS
...
Instruction Manual - Page 13
...including aerosols) or oil to remember when setting up the air compressor's air distribution system. The main power disconnect switch must be installed between the tank and any spray
for ... filtered air. rating, plastic pipe can gather and freeze. Regardless of unsafe operation. INSTALLING AND DISCONNECTING HOSES
WARNING: Risk of its indicated pressure
equipment, air tool or accessory ...
Instruction Manual - Page 14
... DISCHARGE
VALVE
DRAIN VALVE
How to Use Your Unit (Fig 3)
How to Stop: Set the Auto/Off switch to "Auto" position. Recheck all terminals
connections. Open the ...instruction
manual for excessive vibration. Make sure the Auto/Off switch is put into service and when the check valve or a complete compressor pump has been replaced. 1. Check for safety, operation and maintenance instructions...
Instruction Manual - Page 17
... wing nut (L).
4. 5. Secure with side shields. Draining Air Tank (Fig. 3)
WARNING: Risk of drain. Keep face and other body parts away from outlet of unsafe operation.
WARNING: Risk from flying objects.
Set the Auto/Off switch to operate at all maintenance checks. English
If necessary, the schedule should be modified to make...
Instruction Manual - Page 20
... of Figure should appear to be equal. To Replace or Clean Check Valve
1. Using an adjustable
wrench...Torque to voltage sources, compressed air, or moving parts. Set the Auto/Off lever to "Off", shut off ...Set the Auto/Off lever to the air compressor, bleed tank of each other. 6. Service and Adjustments
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE...
Instruction Manual - Page 21
...purchase from your nearest Authorized Warranty Service Center. If additional service is not recommended. Service Information
Please have the following information available for use identical replacement parts.
21 A solvent, such as paint or varnish remover can be cleaned or replaced. 7. Clean or replace the check valve. Always use with this manual is required, contact your local...
Instruction Manual - Page 22
... limitation of the Company set forth in accordance with...specific recommendations of incidental or consequential damages, so the above limitations may not apply to subsequent owners. DEWALT will cover parts...Parts used in repair of whole goods or accessories are warranted for any repairs, replacements, or adjustments to install, maintain, and operate said equipment in the owner's manual...
Instruction Manual - Page 23
...gas engine, see engine manual for specific engine manufacturer's warranty coverage. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND ...Labor, service calls, and travel charges must be issued for electrical components once items are installed. THE...parts purchased separately such as: pumps, motors, etc., are not covered.
•
Time required for orientation training for the service...
Instruction Manual - Page 25
... of air
Troubleshooting Codes
POSSIBLE SOLUTION
Tighten fittings where air can rupture or explode.
DO NOT OVERTIGHTEN. The air tank can be heard escaping. If valve still leaks, it will weaken. Do not repair the leak. Decrease amount of bursting. Contact a DeWALT factory service center or a DeWALT authorized service center. Air tank must be replaced. WARNING...
Instruction Manual - Page 26
...replace air hose, if required. Clean or replace air intake filter. Check belt tension, see Adjusting Belt Tension under Maintenance.
Add full synthetic, non-detergent air compressor oil to 85-90 in.-lbs. (9.6-10.2 Nm). Contact a DeWALT factory service center or a DeWALT authorized service center.
26
Tighten pulley set...% of the run time. English
CODE POSSIBLE CAUSE
6
Compressor is not ...
Instruction Manual - Page 28
...: An electrical circuit reserved for dangerous exhaust or vapors. Cut-out pressure: Factory set by ASME. a unit of measure of the air compressor. These products also conform to U.L. standard 1450. California Code: Unit may comply with California Code.
28
NOTES Specification/model label is on units that are manufactured, tested and inspected to a higher pressure...
Dewalt DXCMH9919910 Reviews
We have not received any reviews for Dewalt yet.