Dewalt DWS709 Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt DWS709 manuals!
Problems with Dewalt DWS709?
Ask a Question
Free Dewalt DWS709 manuals!
Problems with Dewalt DWS709?
Ask a Question
Popular Dewalt DWS709 Manual Pages
Instruction Manual - Page 3
....
• TURN THE MACHINE "OFF", AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, before turning tool on the table and against injury resulting from spindle before adjusting or changing set-ups, when making repairs or changing locations. DANGER: Indicates an imminently hazardous situation which may result in electric shock, fire and...
Instruction Manual - Page 4
... masonry. Severe personal injury may cause damage to the machine or blade and/or serious injury.
• NEVER CUT FERROUS METALS (those with saw could cause serious injury.
• KEEP ARMS, HANDS, AND FINGERS AWAY FROM THE BLADE to operation. Consult the instruction manual for miter saws. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR...
Instruction Manual - Page 5
...OWN SAFETY, READ INSTRUCTION MANUAL BEFORE
OPERATING MITER SAW. KEEP HANDS OUT OF PATH OF SAW BLADE. THINK! If you do this product. Extension Work Support: DW7080
Used to support long overhanging workpieces, the work supports, one Extension Work Support (DW7080) (refer to 42" (107 cm). It is available from 0 to Figure 1). Always make repetitive cuts of such accessories with this...
Instruction Manual - Page 6
... mm)
96
NOTE: For cutting non-ferrous metals, use only saw blades with TCG (Triple Chip Grind) teeth designed for this instruction manual, the carton should contain:
1 DWS709 miter saw 1 DEWALT 12" (305 mm) diameter saw carton to make sure that you have received all parts.
Refer to this purpose.
Left / 0º Miter
7/8" (23 mm)
9-9/16" (354 mm)
Crown Flat (Spring Angle...
Instruction Manual - Page 7
..., miter lock knob, bevel lock knob, lock down . To reduce the risk
of injury, turn counterclockwise, left -hand threads.) 6.
Removing the Blade (Fig. 3)
1.
Unplug the saw from place to another. NOTE: If you must sit flush on adjus- The plywood must
know what and where the parts are provided in all models. 5. IMPORTANT SAFETY INSTRUCTIONS
Changing or Installing...
Instruction Manual - Page 10
...saw blades for certain bevel cuts. DO NOT CROSS HANDS, AS SHOWN IN FIGURE 8C. Pull the saw out, toward you, lower the saw to contact the top of the workpiece while pulling out. Do not allow the saw head down -back motion with the miter arm set.... Saw through the guard louvers when following a pencil line.
8 Refer to the Features and Controls section for detailed instructions on ...
Instruction Manual - Page 11
... the back of the miter saw. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ADJUSTMENTS
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before making repairs. Retighten the four screws. With the miter lock knob unlocked, allow...
Instruction Manual - Page 12
... many bevel positions, one shown in the down position with the set before adjusting or when making repairs. RAIL GUIDE ADJUSTMENT (FIG. 4)
Periodically check the rails for mitering corners like the one of the saw . Sketch A in place and move the fences closer to the blade past the normal limit, then tighten the fence adjustment knobs...
Instruction Manual - Page 13
... at the end of precisely 90º, you will have angles of this manual (Table 1) will assist you develop a feel comfortable with it in Figure 12 are for all standard (U.S.) crown molding with extreme accuracy.
Set your saw has special pre-set miter latch points at 31.62º left 45° Save right side of...
Instruction Manual - Page 15
...support
the work.
BASE FENCE
MAINTENANCE
WARNING: To reduce the risk of material control and possible
injury. They are lubricated for repair. Remove the belt cover. Then rotate
the set screw on the blade...
service center for life and need no further maintenance.
• Periodically clean all dust and wood chips from
power source before installing and removing accessories,...
Instruction Manual - Page 16
... repair information, visit www.dewalt.com or call the local company or see country specific warranty information contained in Latin America.
Use of the correct grade of brush is required under the Federal Consumer Safety Act. New brush assemblies are available at extra cost from power source before installing and removing accessories, before use identical replacement parts...
Instruction Manual - Page 17
...Square to Changing or Installing a New Saw Blade. 1. Dull blade
1. Extension cord too light or too long 2. Refer to Miter Scale Adjustment under Adjustments. 2. Refer to Miter Scale Adjustment under Adjustments. 3. Check and adjust fence. English
TROUBLE! Replace with rubber cement. 1. Blade is not perpendicular to Bowed Material under Important Safety Instructions.
2. Refer...
Parts Diagram - Page 2
...-00 146732-00 N039404 146751-00 150075-00 644999-00 152636-00 391616-00 151962-01 N436564 N365590
Parts List for currentpartsinformation. Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DWS709 Type 20
Description
QtyRequired
LOCKNUT
1
WASHER
4
SLEEVE
1
SCREW
1
FENCE
1
SCREW
4
BEVELKNOB
2
BEARING,THRUST
1
LEFT...
Parts Diagram - Page 5
....
Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DWS709 Type 20
Description
QtyRequired
SCREW
1
BEVELSCALE
1
CLAMPPLATE
1
LEVER
1
BUSHING
1
CLAMPPLATE
1
BALL
1
SHOE
1
BUSHING
1
WEARGUIDE
1
WARNINGLABEL
1
WARNINGLABEL
2
TERMINAL
1
WEARPAD
3
LABEL
1
RING,RET.EXT
1
BEARING
1
SUPPORTHOUSING...
Parts Diagram - Page 6
Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DWS709 Type 20
Description
QtyRequired
COVERPLATE
2
BUMPER
2
SHOULDERSCREW
4
WEARGUIDE
2
SETSCREW
1
ENDCAP
1
TRUNNION
1
SCREW
8
LOCKKNOB
1
SPRING,CONICAL
1
DUSTDUCTASSY.
1
SCREW
1
RAIL
1
ARMASSEMBLY
1
REARGUARD
1
PINIONSHAFTASSY
1
SCREW
4
SPINDLE&...
Dewalt DWS709 Reviews
Do you have an experience with the Dewalt DWS709 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!