Dewalt DWE4120N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE4120N manuals!
Problems with Dewalt DWE4120N?
Ask a Question
Free Dewalt DWE4120N manuals!
Problems with Dewalt DWE4120N?
Ask a Question
Popular Dewalt DWE4120N Manual Pages
Instruction Manual - Page 3
.... Keep cord away from heat, oil, sharp edges or moving parts. Please read the instruction manual. b) Avoid body contact with earthed (grounded) power tools.
c) Keep children and bystanders away while operating a power tool. Never modify the plug in electric shock, fire and/or serious injury. c) Do not expose power tools to these symbols. Use of electric shock. d) Do not...
Instruction Manual - Page 4
... for the connection of dust extraction and collection facilities, ensure these instructions to power source and/ or battery pack, picking up or carrying the tool. e) Maintain power tools. Many accidents are dangerous in unexpected situations. Use of the power tool for misalignment or binding of moving parts. Always wear eye protection. e) Do not overreach. b) Use personal protective...
Instruction Manual - Page 5
... accessory. Depending on the power tool. The eye protection must be within the capacity rating of your hand or arm may make exposed metal parts of the accessory must wear personal protective equipment. SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Safety Warnings Common for damage or install an undamaged accessory. Read all instructions listed below may result in...
Instruction Manual - Page 6
...operator, depending on the power tool and position your control.
e) Do not attach a saw chain woodcarving blade or toothed saw blade.
m) Regularly clean the power tool's air vents. o) Do not ...movement at the point of snagging. l) Do not run the power tool while carrying it at your power tool and the specific guard designed for Grinding and
Abrasive Cutting-Off Operations
a) Use only...
Instruction Manual - Page 7
... at you. The wheel may bind, walk up or kickback if the power tool is in the workpiece. The protruding wheel may occur. Tuck away or trim any oversized workpiece to a complete stop.
Investigate and take corrective action to shatter.
Supports must be used only for recommended applications. English
c) Wheels must be placed...
Instruction Manual - Page 8
... make up the total length, be sure each individual extension contains at all times.
• Air vents often cover moving parts.
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for Cord Sets
Ampere Rating
Volts
Total Length of Cord in loss of accessories not specified in moving...
Instruction Manual - Page 10
... under wet conditions or in presence of it from power source before installing and removing accessories, before adjusting or when making repairs. Lock on Button
D. An accidental start-up can cause injury.
8
DWE4100
G K
DWE4120
I . if this tool. COMPONENTS (Fig. 1, 6)
FIG. 1 C
WARNING: Never modify the power tool or any part of flammable
liquids or gases. Threaded clamp nut...
Instruction Manual - Page 11
.... 2
C
ATTACHING SIDE HANDLE (FIG. 2)
The side handle (C) can be serviced and
re-assembled by a DEWALT service center. Failure to either side of the gear case in .-lbs. Overtightening could cause
screws...and motor housing become separated
by more than 1/8" (3.17 mm), the tool must be fitted to have the tool
serviced may cause brush, motor and bearing failure.
3. torque.
Remove the...
Instruction Manual - Page 13
..., before laying the tool down until the wheel or accessory stops rotating. An accidental start up can be rated for edge grinding. Mounting instructions for use with the slots on pages 9-10. MOUNTING AND REMOVING (TYPE 27)
ONE-TOUCH™ GUARD (FIG. 4, 5)
FIG. 4
NOTE: If your local dealer or authorized service center. While holding...
Instruction Manual - Page 14
... (DWE4120, DWE4120N) (FIG. 6)
To start the tool, slide the ON/OFF slider switch (G) toward the front of the tool and press the forward part of the tool. For continuous operation, slide the switch toward the front of the switch inward. Depress and release the paddle switch as the activation of a
ground fault interrupter, throwing of the tool...
Instruction Manual - Page 16
... a forward and back motion to
avoid creating gouges in the work surface.
4. Remove the tool from your local dealer or authorized service center.
1. Allow
the tool to stop rotating before touching the tool to the work FIG. 13
surface, allowing the tool to operate
at high speed. Place the sanding disc (P) on the clamp nut into...
Instruction Manual - Page 18
...for concrete cutting can result in closed position. Noting the position of these parts
before turning the tool off. Align the FIG. 18
lugs (L) on the gear case. To ...tool but is greatest
5˚-10˚
when the tool operates at high
speed. The guard body
should be positioned between the edge of grinder may be removed before attempting to reach full speed before setting...
Instruction Manual - Page 19
...
WARNING: Blow dirt and dust out of all air vents with clamp lever in these wheels are not designed for cutting wheels.
1. Remove the tool from power source before installing and removing accessories, before adjusting or when making repairs. Undetectable damage to work surface, allowing tool to repair or replace the guard. Apply minimum pressure to work surface...
Instruction Manual - Page 20
.... Always use , for your local dealer or authorized service center. Three Year Limited Warranty
DEWALT will repair, without charge, any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website: www. This warranty gives you specific legal rights and you need assistance in certain...
Instruction Manual - Page 68
... on the surface of pyramids on the handgrip; N157456 DWE4100, DWE4120, DWE4120N Copyright © 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (DEC12) Part No. the array of the tool. the kit box configuration; the "D" shaped air intake grill;
Dewalt DWE4120N Reviews
We have not received any reviews for Dewalt yet.