Instruction Manual
Page 4
...Use clamps or a vise to carry the current your hand and it will draw. It will cause a drop in line voltage resulting in moving parts and should be avoided. • USE SAFETY GLASSES. The following table shows the correct size to use one heavy enough to hold work area well... Recommended Minimum Wire Size for lubricating and changing accessories. Don't carry tool with grounded surfaces. Be sure switch is in damp or wet locations. DW124/384086-01 11/15/02 12:35 PM Page 1 English Safety Instructions For All Tools • KEEP WORK AREA CLEAN. Use only 3-wire ...
...Use clamps or a vise to carry the current your hand and it will draw. It will cause a drop in line voltage resulting in moving parts and should be avoided. • USE SAFETY GLASSES. The following table shows the correct size to use one heavy enough to hold work area well... Recommended Minimum Wire Size for lubricating and changing accessories. Don't carry tool with grounded surfaces. Be sure switch is in damp or wet locations. DW124/384086-01 11/15/02 12:35 PM Page 1 English Safety Instructions For All Tools • KEEP WORK AREA CLEAN. Use only 3-wire ...
Instruction Manual
Page 5
...such as re-bar may be be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! WARNING: Some dust created by an authorized service center unless otherwise indicated elsewhere in loss ...of parts, mounting, and any other conditions that are : • lead from lead-based paints, •...chemicals: work in a well ventilated area, and work . Check for alignment of moving parts, binding of moving parts, breakage of control. DW124/384086-01 11/15/02 12:35 PM Page 2 English function.
...such as re-bar may be be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! WARNING: Some dust created by an authorized service center unless otherwise indicated elsewhere in loss ...of parts, mounting, and any other conditions that are : • lead from lead-based paints, •...chemicals: work in a well ventilated area, and work . Check for alignment of moving parts, binding of moving parts, breakage of control. DW124/384086-01 11/15/02 12:35 PM Page 2 English function.
Instruction Manual
Page 7
...Switches Depressing the trigger switch turns the tool "ON," releasing the trigger switch turns the tool "OFF." NOTE: The switch provided is a common part for operating in mechanical interlock prevents operation of the hole. 8. It's important to tighten chuck with fingers and insert bit fully into the detent... bits, or hole saws. Assemble the bail handle in figure 3. Open the chuck jaws by hand. Always apply pressure in clockwise direction. DW124/384086-01 11/15/02 12:35 PM Page 4 English Assembling Bail Handle A bail handle is provided for carrying the tool and for reversing...
...Switches Depressing the trigger switch turns the tool "ON," releasing the trigger switch turns the tool "OFF." NOTE: The switch provided is a common part for operating in mechanical interlock prevents operation of the hole. 8. It's important to tighten chuck with fingers and insert bit fully into the detent... bits, or hole saws. Assemble the bail handle in figure 3. Open the chuck jaws by hand. Always apply pressure in clockwise direction. DW124/384086-01 11/15/02 12:35 PM Page 4 English Assembling Bail Handle A bail handle is provided for carrying the tool and for reversing...
Instruction Manual
Page 9
DW124/384086-01 11/15/02 12:35 PM Page 6 English MAXIMUM RECOMMENDED...accessories or damage caused where repairs have other qualified service organizations, always using identical replacement parts. For warranty repair information, call 1-800-4-DEWALT for a full refund. This warranty gives you specific legal rights and you are not...repairs, maintenance and adjustment (including brush inspection and replacement) should be required. In addition to the warranty, DEWALT tools are covered by authorized service centers or other rights which vary in metal larger than 1/2" use hole saws...
DW124/384086-01 11/15/02 12:35 PM Page 6 English MAXIMUM RECOMMENDED...accessories or damage caused where repairs have other qualified service organizations, always using identical replacement parts. For warranty repair information, call 1-800-4-DEWALT for a full refund. This warranty gives you specific legal rights and you are not...repairs, maintenance and adjustment (including brush inspection and replacement) should be required. In addition to the warranty, DEWALT tools are covered by authorized service centers or other rights which vary in metal larger than 1/2" use hole saws...