Dewalt DW124K Support Question
Dewalt DW124K Support Question
Find answers below for this question about Dewalt DW124K.Need a Dewalt DW124K manual? We have 1 online manual for this item!
Question posted by jbett98 on November 26th, 2019
Dw124 Angle Drill Trigger Switch Color Code For The Wires To Switch
I accidentally threw away the wiring diagram for my DeWalt DW124 type 1 angle drill trigger switch.There is 4 wires from the motor (black, white, red & blue) and (black & white) from the power cord.The back side of the switch has six slots numbered 1 through 6.Any help would be appreciated, as I don't want to burn up my new $85.00 replacement switch.
Current Answers
Related Dewalt DW124K Manual Pages
Instruction Manual - Page 1
...; and the array of the tool. DW124/384086-01 11/15/02 12:35 PM Page 2
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
Printed in U.S.A. (NOV02-CD-2)
DW124
Copyright © 2002
Form No. 384086-01
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the "D" shaped air intake...
Instruction Manual - Page 3
... in sketch A.
If your unit is the grounding wire. The green (or green and yellow) conductor in sketch D. NE PAS EXPOSER A LA PLUIE ET NE PAS UTILISER DANS LES EMPLACEMENTS HUMIDES.
1/2" CHUCK
SIDE HANDLE
TRIGGER SWITCH
REVERSING SWITCH
Important Safety Instructions
WARNING: When using electric tools, basic safety precautions should always be followed to reduce...
Instruction Manual - Page 4
... enclosures.
• KEEP CHILDREN AWAY. out of reach of a heavy-duty tool. It will cause a drop in line voltage resulting in damp or wet locations. Don't use power tools in loss of power and overheating. Inspect extension cords periodically and replace if damaged. Be sure switch is dusty. • DON'T ABUSE CORD. Never carry tool by authorized service facility...
Instruction Manual - Page 5
... if you do this instruction manual. Have defective switches replaced by power sanding, sawing, grinding, drilling, and other construction activities. CAUTION: When drilling or driving into a live electrical wires may be be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL!
Some examples of harmful chemicals.
2
FIG. 1
DRILLING DIRECTION
TORQUE REACTION DIRECTION
FIG. 2
FIG. 3 To...
Instruction Manual - Page 6
... case.
As the drill bit meets resistance in the low speed range which is recommended when drilling at significant distances from this tool does not operate, check power supply. if this product may contribute to the optimized handle design, the DW124 contains a slip clutch in the material being drilled, the motor responds by a DEWALT-built motor. DEWALT tools are factory tested;
Instruction Manual - Page 7
... key counter clockwise in Figure 6. Make sure that when you release the selector, it is a slide switch built into the detent in figure 3. Switches
Depressing the trigger switch turns the tool "ON," releasing the trigger switch turns the tool "OFF." Use sharp drill bits only. Be sure the material to be necessary to the position shown in a straight line...
Instruction Manual - Page 8
...drill slightly by pushing the switch handle toward you crack the brittle materials. Lubrication
Your tool was properly lubricated before being drilled and then pulling it back toward the material being put back into the wood. Motor Brushes
This DEWALT tool... around cord (Figure 8.)
3. DRILLING IN WOOD Holes in low speed indicates that is apt to splinter should be drilled dry. DW124/384086...
Instruction Manual - Page 9
... of purchase. FREE WARNING LABEL REPLACEMENT: If your DEWALT heavy duty industrial tool, simply return it to the warranty, DEWALT tools are covered by authorized service centers or other rights which... performed by our:
30 DAY NO RISK SATISFACTION GUARANTEE
If you may be required.
DW124/384086-01 11/15/02 12:35 PM Page 6
English
MAXIMUM RECOMMENDED CAPACITIES
CLUTCH OPERATIVE...
Similar Questions
How To Change The Power Cords Of Dw130v
I am trying to change the power cord but I'm not sure how to remove the cap to access the inside of ...
I am trying to change the power cord but I'm not sure how to remove the cap to access the inside of ...
(Posted by Pmello8080 4 years ago)
Power Cord Replacement
I have a dw758 grinder and need the power cord replaced. The old one was disconnected by someone els...
I have a dw758 grinder and need the power cord replaced. The old one was disconnected by someone els...
(Posted by marcusmiles1973 4 years ago)
I Need To Replace Power Cord What Are The Bolts Holding The Case Tovether?...
torx or allen?what size?
torx or allen?what size?
(Posted by onemoorecar3322 6 years ago)
Wiring Diagram For A Dwd520 Type 1 Hammerdrill
How can I get a wiring diagram for a Dewalt DWD520 type 1 hammer drill so I can install my new switc...
How can I get a wiring diagram for a Dewalt DWD520 type 1 hammer drill so I can install my new switc...
(Posted by Paynepropsvc 8 years ago)
Replacing Power Cord.
I am trying to put a power cord on my Dewalt D55146 and not sure how. Can anyone please help.
I am trying to put a power cord on my Dewalt D55146 and not sure how. Can anyone please help.
(Posted by anthonysaboe 9 years ago)